Vanguard Managed Solutions PRVYS18PWA Inspecting Burners, Thermostat Control Operation

Page 17

OWNER’S MANUAL

OPERATING

HEATER

Continued

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety in- formation on page 16. If you don’t smell gas, go to the next step.

5.Turn control knob counterclockwise

C-clockwiseto the PILOT position.

Press in control knob for five (5) sec- onds (see Figure 24, page 16 ).

Note: You may be running this heater for the first time after hook- ing up to gas supply. If so, the con- trol knob may need to be pressed in for 30 seconds or less. This will allow air to bleed from the gas system.

•If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

6.With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is attached to the front burner. If needed, keep press- ing ignitor button until pilot lights.

Note: If pilot does not stay lit, con- tact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Light- ing Procedure.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

Note: If pilot goes out, repeat steps 3 through 7. This heater has a safety interlock system. Wait one (1) minute for system to reset before lighting pilot again.

Ignitor

Thermocouple

Pilot Burner

Electrode

 

Figure 25 - Pilot

(Note: Appearance of pilot assembly may vary by model.)

8.Turn control knob counterclockwise

C-clockwiseto desired heating level. The burners should light. Set control knob to any heat level between HI and LO.

CAUTION: Do not try to adjust heating levels by using the manual shutoff valve.

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

Turn control knob clockwise Clockwise to the OFF position.

Shutting Off Burners Only (pilot stays lit)

Turn control knob clockwise Clockwise to the PILOT position.

THERMOSTAT CONTROL

OPERATION

(Thermostat-Controlled Models

Only)

The thermostat control knob can be set to any comfort level between Hi and Lo. The thermostat will gradually modulate the heat output and flame height from higher to lower settings, or pilot, in order to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.

Note: Selecting the Hi setting with the control knob will cause the burner to remain fully on, without modulating down in most cases.

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 5 under Light- ing Instructions, page 16.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8 above.

INSPECTING

BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT FLAME PATTERN

Figure 26 shows a correct pilot flame pat- tern. Figure 27 shows an incorrect pilot flame pattern. (Note: Appearance of pilot assembly may vary by model.) The incor- rect pilot flame is not touching the thermo- couple. This will cause the thermocouple to cool. When the thermocouple cools, the heater will shut down.

If pilot flame pattern is incorrect, as shown in Figure 27

•turn heater off (see To Turn Off Gas to Appliance, manually controlled models, page 16. Thermostatically controlled models, this page, column 2).

•seeTroubleshooting, pages 18 through 20.

Pilot Burner

Thermocouple

Figure 26 - Correct Pilot Flame Pattern

Pilot Burner

Thermocouple

Figure 27 - Incorrect Pilot Flame Pattern

MAIN BURNER

Periodically inspect all burner flame holes with the heater running. All slotted burner flame holes should be open with yellow flame present. All round burner flame holes should be open with a small blue flame present. Some burner flame holes may be- come blocked by debris or rust, with no flame present. If so, turn off heater and let cool. Either remove blockage or replace burner. Blocked burner flame holes will create soot.

104343

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Oak Log Design What to do if YOU Smell GASLog Design Patent PendingVanguard FLAME-MAX Unvented PROPANE/LP GAS LOG Heater Safety InformationProduct Identification Product FeaturesLocal Codes UnpackingProviding Adequate Ventilation AIR for Combustion and VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining Fresh AIR Flow for Heater Location Ventilation Air From Inside Ventilation AIRBuilding Ventilation Air From OutdoorsCheck GAS Type InstallationInstallation Minimum Non-combustible Material Clearances If Not Using MantelIf Using Mantel Mantel Clearances Determining Minimum Mantel Clear- ance When using a HoodFloor Clearances Determining Minimum Mantel ClearanceChimney Minimum Permanent Height ft Flue Opening sq. ins Installing Damper Clamp Accessory for Vented OperationInstalling Heater Base Assembly Golden Oak and Birch Model Chassis Installation Items NeededStandard Oak Log Chassis Accessories, Connecting to GAS SupplyPressure Testing Gas Supply Piping System Pressure Testing Heater Gas ConnectionsChecking GAS Connections Test Pressures Equal To or Less Than 1/2 PsigFor Golden Oak or Birch Models Installing LogsFor Vintage Oak Model Lighting Instructions Operating HeaterVariable Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off HeaterThermostat Control Operation Inspecting BurnersPilot Flame Pattern Main BurnerObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Gas leak. See Warning statement at TopFor Masonry and FACTORY-BUILT Metal Fireplace Optional Positioning of Thermostat Sensing BulbSpecifications Replacement Parts Cleaning and MaintenanceODS/PILOT and Burner LogsODS Pilot Illustrated Parts BreakdownFLAME-MAX Vintage OAK Models VYS18P and VYS24P VYS18P VYS24P Parts List1117 612 VYD18P, VYBD18P VYD24P, VYBD24P VYD30P, VYBD30P VYD36P Thermostatically Controlled Models VYD18PT VYD24PT VYD30PT VYD18PT VYD24PT VYD30PT VYD18PT VYD24PT VYD30PTService Hints AccessoriesTechnical Service Manual Shutoff104343 Warranty Information

PRVYS18PWA specifications

Vanguard Managed Solutions PRVYS18PWA is a cutting-edge technology platform designed to revolutionize the way individuals and businesses manage their financial investments. This innovative solution combines advanced tools and features to provide a comprehensive approach to asset management.

One of the standout features of PRVYS18PWA is its intuitive user interface, which makes navigating and using the platform a seamless experience for users of all skill levels. The dashboard provides real-time insights and analytics, enabling users to track their investments’ performance easily. Powerful reporting tools are integrated, offering detailed summaries and projections that help users make educated financial decisions.

PRVYS18PWA utilizes state-of-the-art algorithms and machine learning technologies to analyze market data and trends. This feature allows users to receive personalized investment recommendations tailored to their financial goals and risk tolerance. AI-driven tools continuously learn from user interactions, ensuring that the advice provided remains relevant and up-to-date.

Security is a top priority for Vanguard Managed Solutions, and PRVYS18PWA is no exception. The platform incorporates advanced encryption protocols and two-factor authentication to protect sensitive data, ensuring that user information and financial assets are secure at all times. Users can feel confident in their transactions and the integrity of their personal information.

Another impressive characteristic of PRVYS18PWA is its integration capabilities. The platform can seamlessly connect with various financial institutions and other investment tools, allowing users to consolidate all their financial data in one place. This integration streamlines the management process and provides a holistic view of an individual’s or organization’s finances.

For those keen on sustainability, PRVYS18PWA offers various eco-conscious investment options. The platform allows users to explore socially responsible investment opportunities, aligning with personal values and promoting a positive impact on society and the environment.

Furthermore, PRVYS18PWA includes robust educational resources, ensuring users have access to the knowledge needed to make informed investments. From industry insights to market analyses and investment strategies, users can enhance their financial literacy and make more confident decisions.

Overall, Vanguard Managed Solutions PRVYS18PWA is an exceptional investment management tool that combines user-friendly design, advanced technologies, and educational resources to empower users on their financial journeys. Whether a novice investor or a seasoned professional, PRVYS18PWA offers features and functionalities to meet diverse needs and promote financial growth.
Top Page Image Contents