Vanguard Heating VDVF36PN, VDVF36STP, VDVF36STN, VDVF36PP Ghrc Operation, Ghrct Operation

Page 22

® VDVF36P and VDVF36ST Series

DIRECT-VENT GAS FIREPLACE HEATER

OPERATING

FIREPLACE

Continued

1.After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjust- ment knob anywhere between HI and LO. Slide the selector switch to the REMOTE position. Note: The burn- ers may light if hand-held remote ON button was on when selector switch was last turned off. You can now turn the burners on and off with the hand- held remote control unit.

IMPORTANT: Do not leave the se- lector switch in the REMOTE posi- tion when the pilot is not lit. This will drain the battery.

IMPORTANT: Be sure to press the ON/OFF buttons on the hand-held remote control unit for up to 3 sec- onds to assure proper operation.

GHRC Operation:

2a. Press ON/OFF button to turn the burners on and off. When turning burners off, the pilot will remain lit.

GHRCT Operation:

2b. Select the MAN (manual) or AUTO button on the hand-held remote con- trol unit (see Figure 53).

In manual mode, turn burners on or off by pressing the ON or OFF buttons on the hand-held remote control unit.

In auto mode, the room tempera- ture is controlled by the thermo- stat in the hand-held remote con- trol unit. To increase the room tem- perature, press the top arrow of the TEMP button. To lower the room temperature, press the bottom ar- row of the TEMP button. At higher settings the heater will run longer. IMPORTANT: This remote control has been specially engineered to take an air temperature sample ev- ery 5.5 minutes in the auto mode. It will not respond immediately to the temperature setting being turned up or down.

IMPORTANT: The hand-held re- mote control unit must be near the heater. Do not keep the hand-held remote control unit too close to the heater. The thermostat on the hand-held remote control unit will heat up too quickly and turn the heater off.

3.Use the STATUS button on the hand- held remote control unit to see the operation mode being used and the temperature setting selected. A red light will come on beside the opera- tion mode being used when the sta- tus button is pressed.

4.To turn the burners off when operat- ing in the manual mode, press the OFF button. If operating in the auto mode, press the MAN button, then press the OFF button. The pilot will remain lit. IMPORTANT: To turn the pilot off, manually turn the control knob on the heater to the OFF position.

Flame Adjustment Knob

 

 

 

Control Knob in

IH

 

 

On Position

 

F

PIL

ON

 

O

O

F

T

 

 

OFF

 

O

 

 

 

 

N

REMOTE

 

 

 

 

 

LO

 

 

 

Selector Switch in Remote Position

(Optional Remote Control)

Figure 52 - Setting the Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation

Shows Temperature Setting

 

 

HI

 

 

TEMP

Allows Burners to be Turned

 

 

On and Off with the Hand-

 

 

Held Remote Unit.

MAN

LO ON

The Log Heater Will

AUTO

OFF

 

Automatically Cycle Between

 

 

Pilot and the Heat Setting

 

STATUS

 

 

that has been Selected.

 

 

Increases Room Temperature

Decreases Room Temperature

Turns Burners On and Off

Shows Current Operation Mode

Figure 53 - Thermostat Hand-Held Remote Control Unit Selections (GHRCT only)

22

105706

Image 22
Contents Check Local Codes Prior to Installation What to do if YOU Smell GASGlossary Terms Supply Inlets Back SurroundSelecting Location IntroductionBefore YOU Begin Mantel Clearances PRE-INSTALLATION PreparationClearances FramingGeneral Venting Location of Vent TerminationGeneral Venting Installation Planning Venting InstallationInstallation Precautions Installing Vent System in a ChaseInstallation for Horizontal Termination Snorkel TerminationVent Pipe Connections Horizontal Termination Configurations Horizontal VentingVenting with Two 90 Elbows Flat Ceiling Installation Installation for Vertical TerminationCathedral Ceiling Installation Vertical Termination Configurations Venting with One 90 ElbowVertical Venting Venting InstallationParts Lists for Venting High AltitudeElectrical Hookup for Blower Accessory Wall Switch InstallationInstalling Receiver GAS Line HOOK-UP GAS Rating Type of GAS Natural PROPANE/LPGAS Supply Testing Installing LOG SETDecorative Facing Pilot Assembly AdjustmentBurner Flame Adjustment Burner RemovalOperating Guidelines and Maintenance Instructions Lighting Instructions For Your Safety Read Before LightingOperating Fireplace To Turn OFF GAS To ApplianceGhrc Operation Ghrct OperationReplacement Parts Service HintsTechnical Service Wiring DiagramTroubleshooting Observed Problem Possible Cause RemedyObserved Problem Possible Cause Company Gas leak. See Warning statement Pilot Assembly AccessoriesWall Switch KIT Blower KIT DavdbkOrifice Refractory PiecesGAS Control Valve Warranty Information

VDVF36PN, VDVF36STP, VDVF36STN, VDVF36PP specifications

Vanguard Heating has established itself as a noteworthy player in the heating solutions market, and its latest offerings, the VDVF36STN, VDVF36PP, VDVF36STP, and VDVF36PN models, exemplify their commitment to innovative technology and user-centric design. These models are engineered to provide efficient heating solutions while enhancing the aesthetic appeal of any living space.

A standout feature of the Vanguard VDVF36 series is its sleek, modern design. These units seamlessly integrate into various architectural styles, making them an attractive option for both contemporary and traditional interiors. The VDVF36STN, for instance, showcases a stunning see-through option, allowing homeowners to enjoy the ambiance of flames from multiple angles.

These heating appliances utilize advanced gas burner technology, ensuring high thermal efficiency while maintaining a clean-burning flame. This results in reduced carbon emissions, making the VDVF36 series an environmentally responsible choice without compromising performance. The burners are designed to provide even heat distribution, minimizing cold spots and creating a comfortable atmosphere in the desired space.

One of the prominent technologies included in the Vanguard VDVF36 models is the remote control capability. Users can effortlessly manage temperature settings and flame height from the comfort of their seats, enhancing convenience and user experience. Additionally, the units come equipped with multiple flame settings, allowing users to customize the ambiance to match their mood or occasion.

Safety is a top priority in the design of the VDVF36 series. Each model features a built-in safety shutoff system, which automatically turns the unit off in the event of a malfunction, providing peace of mind for homeowners. Additionally, the glass front design incorporates advanced tempered glass technology, ensuring safety and durability while providing an unobstructed view of the flames.

The VDVF36 series also boasts easy installation and maintenance features. Designed for straightforward retrofitting, these units can be integrated into existing chimney systems or used with direct venting options, giving flexibility to home installations. Maintenance is simplified thanks to the accessible components, making routine checks hassle-free.

In summary, the Vanguard Heating VDVF36 models, including the VDVF36STN, VDVF36PP, VDVF36STP, and VDVF36PN, combine advanced technology with aesthetic appeal and safety features, offering users an efficient and stylish heating solution for their homes. Whether enhancing the comfort of a living room or adding charm to a gathering space, these models stand out as exceptional choices in modern heating technology.