Meyer 526, woodchuck, 2900 Installation, General Requirements, Placement And Minimum Clear Ances

Page 16

INSTALLATION

INSTALLATION

GENERAL REQUIREMENTS

CAUTION:

EQUIPMENT MUST BE INSTALLED BY A QUALIFIED

HEATING PERSON.

CAUTION:

ONLY “CLASS A” ALL-FUEL OR SOLID FUEL CHIM-

NEYS INTENDED FOR USE WITH YOUR WOOD-

CHUCK SHOULD BE USED.

FIRST AND ABOVE ALL is safety for you and your family.

MUST USE: Class A Masonry or ULC listed, manufac- tured Class A All Fuels Chimney.

RECOMMENDED SIZE: Rectangular 8"x12" or Round 8".

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. The Woodchuck is to be used in conjunction with a listed gas or oil fired furnace or as a central furnace.

ELECTRICAL SUPPLY: 115 volts, 60HZ, 1 Phase, less than 12 amps.

Install system with 0.2 static pressure.

Flue setting .06 W.C. Max to .04 W.C. Min.

Wood or coal related fires are caused almost exclu- sively by installation, operation or maintenance errors; but not by unsafe equipment.

IMPORTANT: Check with your local state and federal codes on installation at your local fire department.

PLACEMENT AND MINIMUM CLEAR-

ANCES

CAUTION:

FURNACE MUST BE INSTALLED ON A NON-COM-

BUSTIBLE FLOOR OR 3/8" THICK FIREPROOF MILL-

BOARD OR EQUIVALENT.

Locating your unit is very important for proper draft and most efficient heating possible. See figure 7.

FIGURE 7 LOCATING THE WOODCHUCK

15

Image 16

Contents INSTRUCTION AND PARTS BOOK FOR MODELSPhone 715/654-5132 Fax 715/654-5513 07/97Page INTRODUCTION TRANSPORTATION DAMAGESTABLE OF CONTENTS FURNACE SAFETY DANGERDANGER DANGERSPECIFICATIONS MODELDISCLAIMER NOTICE MODELGENERAL INFORMATION HIGH QUALITY CONSTRUCTIONEFFICIENCY COMFORTADDITION COMFORT AND SAVING FIGURE FIGUREOPERATION PROCEDURE IN THE EVENT OF POWER FAILURE OPERATIONCOMMON SENSE IF YOU HAVE CHIMNEY FIREOPERATING YOUR WOODCHUCK FURNACE BURNING WOOD IN YOUR WOOD- CHUCKSTARTUP FIGURE 5 WOODCHUCK CONTROLSASH REMOVAL HELPFUL HINTSBURNING COAL IN YOUR WOOD- CHUCK STARTING A COAL FIRERECHARGING BANKINGOPTIONAL CATALYTIC COMBUSTOR FOR MODELS 2900/4000 MAINTENANCEASH REMOVAL TROUBLE SHOOTING PROBLEMSOLUTION POSSIBLE CAUSEPROBLEM SOLUTIONPOSSIBLE CAUSE 9. Excessive amounts ofINSTALLATION PLACEMENT AND MINIMUM CLEAR ANCESGENERAL REQUIREMENTS FIGURE 7 LOCATING THE WOODCHUCKFIGURE 8 TYPICAL CHIMNEY CHECKLIST TYPICAL STOVE PIPE INSTALLATION CHIMNEY INSTALLATIONFIGURE 9 CHIMNEY/ROOF CLEARANCE INSTALLING YOUR WOODCHUCK STOVE PIPE INSTALLATIONINSTALLATION OF A BAROMETRIC DRAFT DAMPERS IN STOVE PIPESAIR DUCT INSTALLATION ADD-ONINSTALLATIONSWOODCHUCK FINAL ASSEMBLY OPTIONAL SHAKER GRATE INSTALLATION FOR MODELFIGURE 12 PARALLEL ADD-ONINSTALLATION FIGURE 13 CENTRAL ADD-ONINSTALLATIONFIGURE 14 POOR INSTALLATIONS INSTALL SHAKER GRATE HANDLE MODEL 2900 ONLYFIGURE 15 INSTALL SHAKER GRATE HANDLE FIGURE 16 INSTALL OPTIONAL SHAKER GRATE FOR MODEL INSTALL FIREBRICKFIGURE 17 INSTALL FIREBRICK FIGURE 19 INSTALL MANUAL DRAFT-MODEL526 ASSEMBLE MANUAL DRAFT MODEL 526 ONLYINSTALL CIRCULATING BLOWER INSTALL FILTER BOXFIGURE 21 INSTALL CIRCULATING BLOWER AND FILTER ELECTRICAL HOOKUP FIGUREFIGURE 22 ELECTRICAL WIRING DIAGRAM REPAIR PARTS BASIC UNIT FOR MODELKEY NO. PART NO DESCRIPTIONBASIC UNIT FOR MODEL KEY NO. PART NODESCRIPTION KEY NO. PART NOBASIC UNIT FOR MODEL KEY NO. PART NODESCRIPTION KEY NO. PART NOOPTIONAL SHAKER GRATE FOR MODEL SHAKER GRATE FOR MODELS 2900/4000FILTER BOX 2900/4000DESCRIPTION CIRCULATING BLOWER COMFORT CONTROLKEY NO. PART NO. DESCRIPTION PERSONAL DATA INFORMATION FOR FUTURE REFERENCE Page LIMITED WARRANTY

Related manuals

Manual 36 pages 11.61 Kb