Goodman Mfg GME8 service manual Blower Performance Specifications

BLOWER PERFORMANCE SPECIFICATIONS

BLOWER PERFORMANCE

(CFM & Temperature Rise vs. External Static Pressure)

Model		Tons AC				EXTERNAL STATIC PRESSURE (Inches Water Column)
(HeatingAs ShippedSpeed)	Motor
		at 0.5"	0.1				0.2			0.3			0.4			0.5			0.6	0.7	0.8
	Speed
		ESP	CFM	RISE			CFM	RISE		CFM	RISE		CFM	RISE		CFM	RISE		CFM	CFM	CFM
	T1	2.5	875		59		793		65	736		70	674		77	592		88	556	509	460
GME8	T2	3.5	1,032		50		965		54	914		57	861		60	810		64	756	712	659
	T3	1.5	1,217		43		1,153		45	1,098		47	1,051		49	1,009		51	964	918	877
0703BXC*
	T4	3	1,365		38		1,313		39	1,268		41	1,221		42	1,172		44	1,129	1,086	1,054
	T5	4	1,549		33		1,505		34	1,460		36	1,420		37	1,378		38	1,350	1,305	1,268
	T1	2.5	1,268		53		1,198		56	1,151		58	1,092		61	1,041		64	988	932	883
GME8	T2	3.5	1,362		49		1,305		51	1,261		53	1,212		55	1,170		57	1,121	1,074	1,021
	T3	3	1,576		42		1,519		44	1,473		45	1,426		47	1,398		48	1,341	1,290	1,252
0905CXC*
	T4	4	1,755		38		1,711		39	1,657		40	1,627		41	1,579		42	1,548	1,502	1,463
	T5	5	2,183		31		2,128		31	2,094		32	2,060		32	2,014		33	1,992	1,944	1,847
	T1	3	1,466		58		1,415		60	1,357		63	1,306		65	1,248		68	1,202	1,144	1,088
GME8	T2	4	1,642		52		1,596		53	1,552		55	1,499		57	1,449		59	1,388	1,352	1,306
	T3	2.5	1,750		49		1,750		49	1,707		50	1,667		51	1,610		53	1,574	1,531	1,486
1155CXC*
	T4	4	1,870		46		1,805		47	1,782		48	1,737		49	1,701		50	1,656	1,606	1,571
	T5	5	2,297		37		2,297		37	2,224		38	2,106		40	2,014		42	1,896	1,813	1,669

1.CFM in chart is without filters(s). Filters do not ship with this furnace, but must be provided by the installer.

2.All furnaces ship as high speed cooling. Installer must adjust blower cooling speed as needed.

3.For most jobs, about 400 CFM per ton when cooling is desirable.

4.INSTALLATION IS TO BE ADJUSTED TO OBTAIN TEMPERATURE RISE WITHIN THE RANGE SPECIFIED ON THE RATING PLATE.

5.The chart is for information only. For satisfactory operation, external static pressure must not exceed value shown on rating plate. The shaded area indicates ranges in excess of maximum external static pressure allowed when heating. The data for 0.6" w.c. to 0.8" w.c. is shown for air conditioning purposes only.

6 The dashed (---) areas indicate a temperature rise not recommended for this model.

7.The above chart is for U.S. furnaces installed at 0-4000 feet. At higher altitudes, a properly derated unit will have approximately the same temperature rise at a particular CFM, while the ESP at that CFM will be lower.

12