Louisville Tin and Stove 78111 warranty Optional Kits, Side Discharge on Casing, Model, Number

OPTIONAL KITS - CONTINUED

	SIDE DISCHARGE ON CASING		SIDE DISCHARGE (With Extension Boot)
1.	Use optional kit No. 306SR-A.	1.	Use optional kit No. 30SRB-A.
2.	Cut out and remove embossed area on casing side.	2.	Cut opening in drywall as shown in Fig. 17.
3.	Remove knockout from inner liner.	3.	Position plasterground as shown in Fig. 17 (optional).
4.	Place 1-1/2” boot from kit through opening, matching	4.	Cut out and remove embossed section on casing side.
	flanges of boot to knockout on inner boot.	5.	Remove knockout on inner liner.
5.	Mark screw holes and remove boot.	6.	Put heater into position.
6.	Drill holes with a 1/8” drill.	7.	Place inner boot into position, mark and cut boot flush with
7.	Attach inner boot with screws provided.		wall. Place outer boot into position, mark and cut boot flush
8.	Place grille into position, drill holes into casing, and		with wall.
	attach with screws provided.	8.	Place boot trim into position, slide inner boot through wall
			from adjacent room and attach to inner liner. Slide outer
			boot through wall from adjacent room and attach to casing
			side.
		9.	Place grille into position and secure to wall.

				18”
			Min.
	FIGURE 16
				90
				De
			g		r
			e		e
											FIGURE 17
			Outside Corner							14PEK-A PLUG EXTENSION KIT INSTRUCTIONS
				3	F					FOR NON-RECESSED INSTALLATION ONLY
			T		.
			SECTION								UNITS WITH TERMINAL BOARD
		A	L					STEP 1. Turn heater off following Section 3 in “Lighting Instructions” and allow
										to cool.
	W
		L						STEP 2. Turn off all electricity to heater.
				3	F			STEP 3. Remove top louver assembly, fan shroud and fan blade.
								STEP 4. Loosen two screws on romex connector.
			T		.
								STEP 5. Remove junction box cover plate.
			SECTION					STEP 6. Disconnect three power cord terminals and pull power cord out of top
										of heater.
								STEP 7. Insert power cord provided in kit through romex connector and plug
										onto terminal board following wiring diagram found in lighting and
										operating instructions.
								STEP 8. Tighten two screws on romex connector.
					B		O	STEP 9. Replace junction box cover plate.
								STEP 10. Replace fan blade, fan shroud and top louver assembly.
F				I	T		T
								STEP	11	. Snap 90 Degree outside corner (Ref. 1) onto 3 ft. section (Ref. 2)
					O	M
	G			U						plastic raceway. Insert power cord and remove blue backing from
	MODEL			Length of bottom section SE
	R			E	C		T			adhesive strip on raceway and apply to side of heater. See Figure 18.
	NUMBER			(Ref. 4) plastic raceway			O	STEP 12. Insert power cord into second 3 ft. section of raceway (Ref. 3) and
	CF35			18	I
				5-5/16 Inches						remove blue backing and apply to side of heater, butting up agianst
					N
	CF50			8 Inches						bottom of other section. See Fig. 18.
	CF55			14 Inches				STEP 13. Cut 14 inch long bottom section to required length (see chart), insert
	CF65			14 Inches						power cord, remove backing and apply to side of heater. See Fig. 18.
								STEP 14. Plug power cord into wall receptacle, see Fig.18.
	NOTE: Above lengths terminate							STEP 15. Light the heater following lighting instructions.
	approximately 2 inches above floor.							Page 17