Louisville Tin and Stove 78111 warranty Proper Burner Flame, Operation

Page 12

PROPER BURNER FLAME

A proper flame will have a dark blue inner mantle that sits right on top of the burners with a lighter blue outer mantle rising above the burner, (See Figure 11). There may be some yellow where the pilot flame and burner flame meet. There is no primary air adjustment on the burner, and proper flame is assured since the correct manifold pressure and orificing has been done at the factory. NOTE: It is advised that the burner flames be checked at least twice during the heating season for any changes in burner flame characteristics. The appliance area must be kept clear and free from combustible materials, gasoline, and other flammable vapors and liquids. This heater comes from the factory with the proper burner orifice for elevations up to 2,000 feet. Heaters installed above 2,000 feet must be derated 4% for every 1,000 feet. For the proper orifice size find the Model Number and elevation on the orifice chart (See CONTROLS). Replace burner orifice.

5” to 7”

Approx.

1”

FIGURE11

OPERATION

This heater is equipped with a slow opening gas control. On a call for heat the gas valve does not snap-open to full manifold pressure, but opens with a gradual increase to normal manifold pressure. The time lapse from the call for heat to normal operating pressure is two to five seconds. The slow open feature assures a safe, less noisyignition.

After the heat exchanger has warmed sufficiently, the fan will automatically come on to efficiently transfer the heat into the room. NOTE: All but the 35,000 BTU unit (which is one speed) have an automatic two-speed fan. In a new installation or on fall start-up in a very cold room, some on-off cycling of the fan may occur if the heat exchanger cools too much. The burner, however, will continue to operate and the fan cycle until the thermostat is satisfied.

Page 12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Installation and Service Must be Performed Byaqualified INSTALLER, Service Agency orWhat to do Ifyou Smell GAS GAS SupplierContents Counterflow Wall Furnace SpecificationsIntroduction Safety Rules Read Carefully Before Installing UnitVenting Venting See Listof Possiblecausesand Corrections on PAGE19Combustionandventilationair Location and Special Precautions ROUGH-IN InstructionsElectrical ROUGH-IN GAS ROUGH-IN Installation When Installed Flush to Wall Installation / When RecessedPilot Adjustment Pilot Flame AdjustmentNatural GAS GASStanding Pilot For Your Safety Read Before Lighting Lighting InstructionsTo Turn OFF GAS to Appliance What to do if YOU Smell GASWhatto do Ifyou Smellgas Gascontrol KnobProper Burner Flame OperationAuxiliary Limit Switch Maintenance InstructionsTerminal Block Wiring Diagram CF353C-H, CF354C-H Pictorial Schematic Pictorial SchematicSchematic Standing Pilot CF503/504C-H, CF653/654C-HPictorial Model no AmpsOptional Accessory Kits ROUGH-INS for Rear or Side DischargeRear SideOptional Kits Side Discharge on CasingModel NumberTrouble Shooting Chart for qualified serviceman Main Burner Trouble Shooting Chart Pilot and ValveSymptom Possible Causes Corrective Action Possible Causes Corrective ActionReplacementparts Control AssemblyCounterflow Wall Furnace / Standing Pilot USE OnlyfactorysuppliedRequires TWO VO LT System W ITH LO W -B.T.U. Standing Pilo TCounterflow Wall Furnace / I.I.D. Pilot NAT. GAS CF357C-H CF557C-HModels VO LT S YS TEM W ITH Intermittent IG Nitio N I.I.D Rear Register W Boot Flush KIT no 306SR-A Side Register Flush 30SRB-AKIT no Rear Register RecessREV /05 March Your GAS Control and Pilot Light System Tampering is DangerousLimited

78111 specifications

Louisville Tin and Stove 78111 has firmly established itself as a leading provider of heating and cooling solutions in the heart of Louisville, Texas. Known for its commitment to quality craftsmanship and customer satisfaction, this company offers a diverse range of products tailored to meet a variety of residential and commercial needs. One of the standout features of Louisville Tin and Stove is its extensive selection of traditional and contemporary stoves, which include wood, gas, and pellet options. These stoves are designed to provide efficient heating while adding a touch of style to any space.

The technology behind the products at Louisville Tin and Stove focuses on efficiency and sustainability. Many of the stoves are engineered with advanced combustion systems that maximize heat output while minimizing emissions. This not only promotes environmental responsibility but also enhances the cost-effectiveness of heating systems. High-efficiency models are equipped with features such as automated ignitions, programmable thermostats, and even smart technology that allows users to control their heating systems remotely from their smartphones.

In addition to stoves, Louisville Tin and Stove specializes in custom metal fabrication. Whether it’s for a personalized chimney cap or a unique fireplace surround, the skilled craftsmen at this company can bring any vision to life. Their attention to detail and use of high-quality materials ensure that each piece is not only functional but also visually appealing.

Another critical characteristic of Louisville Tin and Stove 78111 is its focus on customer support. The knowledgeable staff is always on hand to provide expert advice on product selection, installation, and maintenance. This commitment to exceptional service ensures that customers feel confident in their purchases and satisfied with their heating solutions.

Overall, Louisville Tin and Stove 78111 combines traditional craftsmanship with modern technology, resulting in a product line that is both stylish and efficient. Whether you’re looking to upgrade your home’s heating system or need a bespoke metal piece, Louisville Tin and Stove stands ready to meet your needs with professionalism and expertise.
Top Page Image Contents