Louisville Tin and Stove 78111 Safety Rules, Read Carefully Before Installing Unit, Venting

Page 3

SAFETY RULES

1.Improper installation, adjustment, alteration, service or maintenance can cause property damage, bodily injury or death. If you do not understand these instructions or your local codes, call local authorities, a qualified installer, service agency, gas supplier, or the manufacturer.

2.Do not install this fan type wall furnace in a recreational vehicle trailer or mobile home.

3.Do not operate this fan type wall furnace unless it is connected to a properly installed and maintained vent system. Do not exhaust flue gases into the room, wall or attic space for any reason.

4.Locate the thermostat in a room or space that cannot be separated by a door or other means from the room or space in which the front outlet grill is installed.

5.Adequate air for combustion and venting must be provided.

6.If rising water may enter the wall furnace, turn off the gas immediately and disconnect the electric service. Do not use the wall furnace if any part has been under water. Immediately call a qualified service technician to inspect the wall furnace and to replace any part of the control system or any gas control which has been under water.

7.Have your fan type wall furnace and vent system inspected at least annually by a qualified service agency.

8.Before cleaning or servicing the wall furnace, turn off the gas and allow it to cool. This will prevent burns.

9.Due to high temperatures, the furnace should be located out of traffic and away from furniture and draperies.

10.Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.

11.Young children should be carefully supervised when they are in the same room as the furnace.

12.Clothing or other flammable material should not be placed on or near the furnace.

13.Any safety screen guard or gill removed for servicing must be replaced prior to operating the furnace.

14.Locate the blocked flue switch and the auxiliary limit switch and push in the reset button. This will reset the switch in case it accidentally opened during shipping.

READ CAREFULLY BEFORE INSTALLING UNIT

These installation instructions are a general guide, and do not supersede applicable local codes and ordinances. Before planning or making the installation, be sure it complies with all phases of the local heating code. Or, in the absence of local codes, the latest edition of the National Fuel Gas Code, ANSI.Z223.1. In Canada, see latest edition of CAN1-B149.

The appliance, when installed must be electrically grounded in accordance with local codes or, in the absence of local codes, the latest edition of the National Electrical Code, ANSI/NFPA No. 70. In Canada, see latest edition of CSA C22.1.

The ANSI standards are available from the American Gas Association, 1515 Wilson Blvd., Arlington, Virginia 22209.

The NFPA standards are available from the National Fire Protection Association, Batterymarch Park, Quincy, MA. 02269. Canadian standards are available from International Approval Services, 178 Rexdale Blvd., Etobicoke, Ontario, Canada M9W 1R3.

VENTING

This appliance must be properly connected to a venting system. Consult local ordinances governing venting. Install only UL listed type BW 4” oval gas vent. When the vent enters the attic, a listed type B-1 round flue pipe may be used. See Figure 1, Page 4.

Vent pipe must connect to the wall furnace or header plate with a “B” vent base plate and terminate with a cap at a point at least 12 ft. above the bottom of the wall furnace and two feet above any obstacle within a 10 foot radius and at least 3 foot above the roof.

Provisions must be made for adequate combustion and ventilation air. This appliance must not be connected to a chimney flue serving a separate solid fuel burning appliance.

All type “B” vents shall extend in a generally vertical direction with offsets not exceeding 45 degrees, except that a vent system having not more than one 60 degree offset may be allowed.

Any angle greater than 45 degrees from the vertical is considered horizontal. The total horizontal run of a vent plus the horizontal vent connector shall be not greater than 75 percent of the vertical height of the vent. Any offsets used should be as far above the drafthood as possible to allow a venting action to begin before any restriction is encountered.

Page 3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents GAS Supplier Installation and Service Must be PerformedByaqualified INSTALLER, Service Agency or What to do Ifyou Smell GASContents Counterflow Wall Furnace SpecificationsIntroduction Safety Rules Read Carefully Before Installing UnitVenting See Listof Possiblecausesand Corrections on PAGE19 VentingCombustionandventilationair Location and Special Precautions ROUGH-IN InstructionsElectrical ROUGH-IN GAS ROUGH-IN Installation / When Recessed Installation When Installed Flush to WallGAS Pilot AdjustmentPilot Flame Adjustment Natural GASWhat to do if YOU Smell GAS Standing Pilot For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS to ApplianceGascontrol Knob Whatto do Ifyou SmellgasOperation Proper Burner FlameAuxiliary Limit Switch Maintenance InstructionsTerminal Block Wiring Diagram Standing Pilot CF503/504C-H, CF653/654C-H CF353C-H, CF354C-H Pictorial SchematicPictorial Schematic SchematicModel no Amps PictorialSide Optional Accessory KitsROUGH-INS for Rear or Side Discharge RearNumber Optional KitsSide Discharge on Casing ModelTrouble Shooting Chart Pilot and Valve Trouble Shooting Chart for qualified serviceman Main BurnerPossible Causes Corrective Action Symptom Possible Causes Corrective ActionUSE Onlyfactorysupplied ReplacementpartsControl Assembly Counterflow Wall Furnace / Standing PilotVO LT System W ITH LO W -B.T.U. Standing Pilo T Requires TWOCounterflow Wall Furnace / I.I.D. Pilot NAT. GAS CF357C-H CF557C-HModels VO LT S YS TEM W ITH Intermittent IG Nitio N I.I.D Rear Register Recess Rear Register W Boot FlushKIT no 306SR-A Side Register Flush 30SRB-A KIT noREV /05 March Tampering is Dangerous Your GAS Control and Pilot Light SystemLimited

78111 specifications

Louisville Tin and Stove 78111 has firmly established itself as a leading provider of heating and cooling solutions in the heart of Louisville, Texas. Known for its commitment to quality craftsmanship and customer satisfaction, this company offers a diverse range of products tailored to meet a variety of residential and commercial needs. One of the standout features of Louisville Tin and Stove is its extensive selection of traditional and contemporary stoves, which include wood, gas, and pellet options. These stoves are designed to provide efficient heating while adding a touch of style to any space.

The technology behind the products at Louisville Tin and Stove focuses on efficiency and sustainability. Many of the stoves are engineered with advanced combustion systems that maximize heat output while minimizing emissions. This not only promotes environmental responsibility but also enhances the cost-effectiveness of heating systems. High-efficiency models are equipped with features such as automated ignitions, programmable thermostats, and even smart technology that allows users to control their heating systems remotely from their smartphones.

In addition to stoves, Louisville Tin and Stove specializes in custom metal fabrication. Whether it’s for a personalized chimney cap or a unique fireplace surround, the skilled craftsmen at this company can bring any vision to life. Their attention to detail and use of high-quality materials ensure that each piece is not only functional but also visually appealing.

Another critical characteristic of Louisville Tin and Stove 78111 is its focus on customer support. The knowledgeable staff is always on hand to provide expert advice on product selection, installation, and maintenance. This commitment to exceptional service ensures that customers feel confident in their purchases and satisfied with their heating solutions.

Overall, Louisville Tin and Stove 78111 combines traditional craftsmanship with modern technology, resulting in a product line that is both stylish and efficient. Whether you’re looking to upgrade your home’s heating system or need a bespoke metal piece, Louisville Tin and Stove stands ready to meet your needs with professionalism and expertise.
Top Page Image Contents