Allied Air Enterprises 80G1UH2V, A80UH2V Vent Connection, Venting Using a Masonry Chimney

Page 15

These series units are classified as fan assisted Category I furnaces when vertically vented according to the latest edition of National Fuel Gas Code (NFPA 54 / ANSI Z223.1) in the USA. A fan assisted Category I furnace is an appliance equipped with an integral mechanical means to either draw or force combustion products through the combustion chamber and/or heat exchanger. This unit is not approved for use with horizontal venting.

NOTE: Use these instructions as a guide. They do not supersede local codes. This furnace must be vented according to all local codes these installation instructions, and the provided venting tables in these instructions.

The venting tables in this manual were extracted from the National Fuel Gas Code (NFPA 54 / ANSI Z223.1) and are provided as a guide for proper vent installation. Proper application, termination, construction and location of vents must conform to local codes having jurisdiction. In the absence of local codes, the NFGC serves as the defining document.

Refer to the tables and the venting information contained in these instructions to properly size and install the venting system.

IMPORTANT

Once the venting system is installed, attach the “Disconnected Vent” warning sticker to a visible area of the plenum near the vent pipe. See Figure 23. The warning sticker is provided in the bag assembly. Order kit 66W04 for additional stickers.

WARNING

Asphyxiation hazard. The exhaust vent for this furnace must be securely connected to the furnace flue transitiion at all times.

Vent Connection

Figure 23

Use self drilling sheet metal screws or a mechanical fastener to firmly secure the vent pipe to the round collar of the flue transition. If self drilling screws are used to attach the vent pipe, it is recommended that three be used. Drive one self drilling screw through the front and one through each side of the vent pipe and collar. See Figure 23.

Install the first vent connector elbow at a minimum of six inches (152 mm) from the furnace vent outlet. See Figure 23.

Venting Using a Masonry Chimney

The following additional requirements apply when a lined masonry chimney is used to vent this furnace.

Masonry chimneys used to vent Category I central furnaces must be either tile lined or lined with a listed metal lining system or dedicated gas vent. Unlined masonry chimneys are prohibited. See Figures 24 and 25 for common venting.

A chimney with one or more sides exposed to the outside of the structure is considered to be an exterior chimney.

An exterior masonry chimney that is not tile lined must be lined with B1 vent or a listed insulated flexible metal vent. An exterior tile lined chimney that is sealed and capped may be lined with a listed uninsulated flexible metal vent.

If the existing chimney will not accommodate a listed metal liner, either the chimney must be rebuilt to accommodate one of these liners or an alternate approved venting method must be found.

Insulation for the flexible vent pipe must be an encapsulated fiberglass sleeve recommended by the flexible vent pipe manufacturer. See Figure 24.

Common Venting Using Metal Lined

Masonry Chimney

NOTE 1: Refer to the provided venting tables for installations. Refer to the capacity requirements shown in the provided venting tables.

Figure 24

506471-01

Issue 1034

Page 15 of 41

Image 15
Contents A80UH2V & 80G1UH2V Table of ContentsFront View Side View A80UH2V & 80G1UH2V Unit Dimensions inches mmExploded View Shipping and Packing List Safety InformationInstalled Locations A80UH2V & 80G1UH2V Gas FurnaceInstalled in Combination with a Cooling Coil Temperature RiseCombustion, Dilution & Ventilation Air Product Contains Fiberglass WoolUnconfined Space Confined SpaceAir from Outside Equipment in Confined Space ALL AIR from Outside Setting Equipment Upflow Application Installation ClearancesUpflow Applications Front View Return Air Upflow ApplicationsRemoving the Bottom Panel Horizontal ApplicationsReturn Air Horizontal Applications Supply Air Plenum Horizontal Application Unit installed on PlatformFilters Duct SystemVenting Mounting Screws LocationUpflow Position Horizontal Position Horizontal Left PositionHorizontal Right Position Venting Using a Masonry Chimney Common Venting Using Metal Lined Masonry ChimneyVent Connection General Venting Requirements Issue Issue 506471-01 Issue Issue 506471-01 Issue Carbon Monoxide Poisoning Hazard Removal of the Furnace from Common VentGas Piping Gas SupplyGas Pipe Capacity ft³/hr m³/hr Horizontal Applications Possible Gas Piping Configurations Electrostatic Discharge ESD Interior MAKE-UP BOX InstallationLeak Check ElectricalElectrical Wiring Indoor Blower SpeedsGenerator Use Voltage Requirements Humidifier Automatic Heat Staging Jumper Electronic Air CleanerVariable Speed Features ThermostatHeating Mode Cooling ModeAdjusting Airflow Lighting Instructions What to do if you smell gasTo Shut Down Furnace Single Stage Cooling Two Stage CoolingHeat Pump 1st Stage 2nd Stage W1/W2 Heat Call High Heat W2 CallCall for Fan Checking and Adjusting Gas Input ControlsGAS Valve Shown in on Position Manifold Pressure Settings BTU/HRInput Burners Typical Flame AppearanceLubrication LED TroubleshootingFailure Codes Red LED High Heat State Green LEDControl Group Heat Exchanger Group Blower GroupBurner Group WHT RED RED/BLK ORN BLU VLT Wiring DiagramTypical Field Wiring Diagram START-UP & Performance Check List Unit SET UP Unit Operation

80G1UH2V, A80UH2V specifications

Allied Air Enterprises has made a significant mark in the HVAC industry with its innovative and high-performance heating and cooling solutions. Among its impressive lineup, the Allied Air Enterprises 80G1UH2V and A80UH2V models stand out for their efficiency, reliability, and advanced features.

The 80G1UH2V is a two-stage gas furnace that operates on natural gas or propane. With an efficiency rating of up to 80%, it provides excellent heating performance while contributing to cost savings on utility bills. Its durable cabinet design ensures long-lasting performance and protection from harsh weather conditions, making it ideal for a variety of home environments.

One of the key features of the 80G1UH2V is its two-stage heating capability. This technology allows the furnace to operate at a lower capacity to maintain consistent temperatures during milder weather, reducing energy consumption and noise. When the temperature drops significantly, the furnace automatically shifts to high capacity, delivering the required heat promptly. This flexibility not only creates a more comfortable living space but also enhances energy efficiency.

The A80UH2V model shares similar traits with the 80G1UH2V but offers some additional features. It includes a variable-speed blower motor that optimizes airflow throughout the home. This innovation not only increases comfort levels but also facilitates quieter operation. The A80UH2V's advanced control system provides precise temperature management and can be integrated easily with smart home systems for enhanced automation.

Both models are designed to operate quietly, with noise levels minimized through improved insulation and sound-dampening technologies. This makes them suitable for residential applications, where comfort and peace are a priority. Additionally, they come equipped with a self-diagnostic control board that makes troubleshooting and maintenance simpler and more efficient.

Durability is another critical characteristic of both the 80G1UH2V and A80UH2V. They feature a robust heat exchanger made from high-quality materials, enhancing longevity and reliability. With these models, homeowners can expect reliable performance for years with minimal upkeep.

In summary, the Allied Air Enterprises 80G1UH2V and A80UH2V models deliver exceptional heating solutions through advanced technology, efficiency, and reliability. Their innovative features cater to the modern homeowner's need for comfort, control, and energy savings, making them excellent choices for residential heating needs.