Lennox Hearth II-T C FS, II-T C INS operation manual Top Surround Panel

Page 11

INSTALLATION

INSTALLING SURROUND ASSEMBLY - Advantage II-T C INS (to be done after venting system is installed)

The surround kit (purchased separately) comes with a set of metal panels that enclose the fireplace opening when fitted together. Put the surround assembly together accord- ing to the following instructions (ref. see illustration below).

1.Remove panels from package.

2.Verify that you have all three panels and a package with “pop” rivets and #8 self-tapping screws. If you do not have a “pop” rivet tool, you should arrange to buy or borrow one for this installation.

3.Set the stove on the hearth so that the rear of the stove is accessible to complete all pipe connections.

4.Verify that the hopper cover is all the way to the front and open as high as your fireplace opening will allow. Secure the hopper cover with at least two #8 screws on all three sides. Tip: Spreading the side panels slightly may be nec- essary to complete this step.

5.Place four rivets and your “pop” rivet tool beside the stove and line up the right side panel (with control door) with the holes in the side of the stove. (When the side panel is properly installed, the hinge flange will be to the rear of the stove.) Attach the panel to the stove with four “pop” rivets.

6.Secure the left side surround panel to the stove using the procedure described in step #5.

7.Before proceeding further, check pipe connections to en- sure that all joints are sealed with high-temperature RTV silicone and properly secured. Refer to detailed venting in- structions on pages 16, 19 and 20.

8.The stove may now be pushed into the fireplace cavity to within 1 1/2” of the face of the fireplace.

9.Set the top surround panel in place over the two side pan- els. Carefully slide the panel downward into the “U” clips

attached to the back of the Advantage II-T C INS. Tip: Be careful to align the notched cutouts in the top surround panel with the stove side panels. Adjust side to side if nec- essary to align with the surround side panels.

10.Unwrap the control board carefully without touching any electrical components. Holding the sides of the control board, lower the bottom edge into the slot in the bottom of the control door opening Install the control board onto the right side panel (with door) us- ing the #8 hex head screw provided.

11.Connect the wiring harness from the Advantage II-T C INS into corresponding connector on control board.

12.Check the Advantage II-T C INS placement in the fireplace. To reposition, open the door and make any needed adjustment by pulling forward and then push- ing sideways. Once the unit has been centered to your satisfaction, close the door and push the Advan- tage II-T C INS back into place so the surround is flush with the face of the hearth. Tip: Before com- pleting this step, verify that the control board will not hit the edge of the fireplace opening.

If using the optional gold surround trim, remove the trim from its packaging and place the piece with the two mi- tered ends along the top panel. Place the two remaining side pieces on the surround so that the mitered ends align. Cut the non-mitered ends of the shroud trim with scissors, if necessary.

In factory built and masonry fireplaces, a means must be provided to prevent room air passage to the chimney cavity of the fireplace. This may be accom- plished by sealing the damper area around the chim- ney liner or pipe.

Top Surround Panel

Left Hinged

Right Hinged

Surround Panel

Surround Panel

Optional Trim

Optional Trim

PAGE 11

www.PelletKing.com

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Freestanding Insert Pellet Fired Stoves Installation and Operation ManualImportant Warnings Table of Contents Smoke Detectors Planning Your InstallationInstallation / Maintenance Standards Selecting a LocationApproved Alternate Materials for Floor/Hearth Protection Floor Protection Advantage II-T C FSListed Material Advantage II-T C ClearancesMinimum Clearances to Combustibles Masonry and Factory Built Fireplaces Model Advantage II-T C FS Pedestal Air Inlet Manufactured Mobile Home INSTAL- LationRemoving Appliance from Pallet InstallationASH PAN Cover Assembly Installing Pedestal to BodyAfter you have begun operation of your stove Installation Check ListCheck list Prior to lighting your stoveTop Surround Panel Rear View of Advantage II-T C FS Thermostat InstallationVenting Requirements Manufactured Mobile Home Chimney Height Requirements Vent TerminationPipe Selection Chart Determining Size of Pipe to InstallInstallation Chart Sample Installation ChartPipe Horizontal Vent Through the Wall Advantage II-T C FS Corner Through the WallTop View Illustration Existing Class a Chimney Vertical Vent Into a Masonry FlueUSA & Canada Direct Connection / Posi- tive Flue Connection Installation Advantage II-T C INSVent Termination When Liner is Used Important Notes Installing Advantage II-T C INSControl Board Care and OperationControl Board Operation Turning OFF Your Pellet Stove PRE-LIGHTING InstructionsStarting Your Pellet Stove General Operating ConsiderationsDamper In less air Damper OperationOverheating Damper Adjustment GuidelineAutomatic Safety Features Power OutageUltraGrateTM FuelUltraGrateTM ASH PAN Advantage II-T C FS Routine MaintenanceRoutine Cleaning Proper Disposal of AshesHeat Exchanger Tubes ASH Trap and BafflesCreosote Removal Door Rope GasketMinimum Frequency of 3 months to 1 year Advantage II-T C FS Opening Side Panels Window WashRemove Window Wash Bracket Opening Side PanelsMotor Lubrication Small Area Paint TOUCH-UPBack View Illustration Specifications Advantage II-T C FSSide View Illustration Side View Front ViewComponent Definitions Wiring Diagram Troubleshooting Qualified Technicians Only Damper Adjustment Guidelines Troubleshooting Qualified Technicians Only Replacement Parts List Firebox Parts Freestanding Only PartsInsert Only Parts Miscellaneous PartsPiece Set UltraGrate TM Kit Replacement Part DiagramsFirebrick Kit Pressure Switch Kit Log Set Cat. #H0430 Optional Accessories List and DiagramsCatalog # Model Description Stove Model Gold Trivet Cat. # H0423 Surround Kits & Trim KitsAdvantage II-T C Pellet Stove Safety Label Advantage II-T C EPA Label & Colorado Compliance Label Simple Operating Instructions Label Installation Tips Ownership Records Service and Maintenance LOGWest Taft Avenue Orange, CA

II-T C FS, II-T C INS specifications

The Lennox Hearth II-T C INS and II-T C FS are exemplary models in the world of modern heating solutions, designed for efficiency, comfort, and style. With innovative engineering and advanced technology, these units cater to the needs of contemporary homeowners seeking reliable and aesthetically pleasing heating options.

One of the main features of the Lennox Hearth II-T C INS and II-T C FS is their exceptional efficiency ratings. These models are designed to operate at high efficiency levels, reducing energy consumption while providing optimal warmth. This not only translates to lower utility bills but also represents a more sustainable choice for environmentally conscious consumers.

A standout characteristic of these products is their versatility in installation. The II-T C INS is an insert model, allowing it to be fitted into existing fireplaces easily. This makes it an ideal option for homeowners wanting to upgrade their current heating systems without extensive renovations. The II-T C FS, on the other hand, is a freestanding stove that adds a classic touch to any room, making it a perfect focal point while offering powerful heating capabilities.

Both models are equipped with advanced technology designed for seamless operation. The hot air circulation system ensures that warmth is evenly distributed throughout the space, eliminating cold spots and enhancing overall comfort. In addition, their adjustable thermostats allow users to set the desired temperature with ease, ensuring a consistent indoor environment.

The Lennox Hearth units are also designed with user convenience in mind. They come with easy-to-use controls and can often be integrated with smart home systems, offering the flexibility to monitor and adjust settings remotely. This modern approach to home heating makes it simple for users to maintain a cozy atmosphere, even on the coldest days.

Moreover, Lennox places a strong emphasis on safety. These heating models include features such as a glass door that remains cool to the touch and a built-in safety shut-off system, providing peace of mind for families.

In summary, the Lennox Hearth II-T C INS and II-T C FS models stand out for their efficiency, versatility, advanced technology, and safety features. With a focus on optimal performance and user convenience, these units represent a significant advancement in home heating, making them an attractive choice for those looking to enhance their living spaces while staying warm and comfortable.
Top Page Image Contents