Kicker ZX850.2, ZX550.2 manuel dutilisation Operation, TroubleShooting, Performance

Page 3
Side View
Slide the housing until it snaps into the metal bracket
Back View
Mount the metal bracket
Figure 6

OPERATION

Operation

Your Kicker ZX.2 series amplifier has three rotary controls on top and one switch on the end-panel. Before turning on the system for the first time, turn the three rotary controls on the top of the amplifier to the full counter-clockwise position.

1.CrossoverSwitch The crossover switch on the end-panel is for setting the internal crossover. In

the OFF position the amplifier passes

 

Figure 5

L-

a full-range signal to the speakers.

 

 

 

 

Use the LO position when connected

 

 

 

 

to a subwoofer. The HI position

 

 

 

L+

should be selected when connected

 

 

 

to speakers, which you do not want

 

 

 

 

to receive any sub-bass information.

 

 

 

 

Never change the crossover

 

 

 

 

"OFF/HI/LO" switch setting with the

 

 

 

 

audio system on! See Figure 1.

Crossover Control

Input Gain Control

Bass Boost Control

 

50 - 200Hz, 12dB/Oct

Low Level: 125mV - 5V, High Level: 250mV - 10 V

0 to +18dB boost @ 40Hz

2.InputGainControl The input gain control is not a volume control. It matches the output of the source unit to the input level of the amplifier. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain on the amplifier up until you can hear audible distortion, then turn it down a little.

3. BassBoostControl The bass boost control is designed to give you increased output 0 - 18dB at 40 Hz. The setting for this control is subjective. If you turn it up, you must go back and adjust the input gain control to avoid clipping the amplifier.

4. CrossoverControl The setting for this control is subjective; 80Hz is a good place to start.

5. RemoteBass(Level Control) When the crossover on your ZX.2 series amplifier is set to LO pass, you have the ability to control the output level of the amplifier remotely. To mount the remote bass level control, simply screw the metal

bracket to the chosen location. Then slide the housing onto the bracket until it snaps into place. Run the cable from the controller to the “Remote Bass” jack on the amplifier chassis.

TroubleShooting

HI-LEVEL

LR

L

R

OFF HI LO

INPUT

 

 

 

 

+ - - +

 

 

 

 

 

 

INPUT

OUTPUT

 

XOVER

If your amplifier does not appear to be

L+

L-

 

R+

R-

working, check the obvious things first

 

REMOTE BASS

 

 

such as blown fuses, poor or incorrect

 

 

 

 

 

wiring connections, incorrect setting of

 

 

 

 

4 Conductor

crossover switch and gain controls, etc.

 

 

 

 

Phone Cable

 

 

 

 

 

There are two LEDs on the top of your

 

 

 

 

 

Kicker ZX series amplifier, one green and one red. When the green LED is lit this indicates the amplifier is turned on and no trouble exists. If the green LED turns off and the red LED is lit, this indicates that the protection circuitry (SORT) is engaged.

￿Green LED off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power terminal

(should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V) 3) Check for reversed power and ground connections 4) Ground terminal, for proper conductivity.

￿ Green LED on, no output? Check the following: 1) RCA connections 2) Test speaker outputs with a “known” good speaker. 3) Substitute source unit with a “known” good source unit. 4) Check for a signal in the RCA cable feeding the amplifier with the “AC” test position selected on the VOM meter.

￿Red LED on, no output? 1) Amplifier is very hot. ￿Thermal protection is engaged. Test for proper impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance and multiple speaker wiring suggestions). Also check for adequate airflow around the amplifier. 2) Amplifier shuts down

only while vehicle is running. ￿Voltage protection circuitry is engaged. Voltage to the amplifier is not within the 9-16 volt operating range. Have the vehicle's charging and electrical system inspected. 3) Amplifier will only play at low volume levels. ￿Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended impedance.

￿ No output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or speaker input) and speaker output connections for the channel 3) Swap the RCA (or speaker input) cable from left to right. If the problem changes sides then you have a bad RCA (or speaker input) cable or source unit problem. 4) Swap the speaker output wire from left to right. If the problem changes sides then you have a bad speaker cable, passive crossover network and/or speaker.

￿Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker input) cable

2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper grounding 4) Check the gain settings and turn them down if they are set too high.

￿Poor stereo image or reduced bass response? ￿Check system phasing by turning the balance control from left to right. If there is more bass output when turned to either side, then check your speaker wiring, passive crossover networks and speaker terminals for proper positive and negative connections. Reverse a speaker connection from positive to negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was out of phase.

If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab, choose the subject you are interested in, and then download or view the corresponding information. Please E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or specific questions.

Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The Kicker Coaxial and Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms) and work with any amplifier designed to operate at a four ohm load. If you want to use two Kicker Coaxial or Component speakers on a single channel of your amplifier wire the speakers in series. This will improve the sound quality, lower the total harmonic distortion and lessen the thermal load at the amplifier. This

may prevent an amplifier from shutting down, due to over-current protection circuitry.

CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can

result in blown amplifier fuses as well as the failure of other critical systems in the vehicle.

Performance

Model

 

ZX350.2

ZX450.2

ZX550.2

ZX850.2

 

 

 

 

RMS Power in Watts, all channels driven

 

 

 

@14.4V, 4Ω Stereo ≤1% THD+N

110 x 2

150 x 2

205 x 2

295 x 2

@14.4V, 2Ω Stereo, ≤1% THD+N

175 x 2

225 x 2

275 x 2

425 x 2

@14.4V, 4Ω Mono, ≤1% THD+N

350 x 1

450 x 1

550 x 1

850 x 1

Length:

13 1/2” (342mm)

16 3/4” (425mm)

20” (507mm)

23 1/4” (590mm)

Specifications common to all models:

 

 

 

Height:

 

 

 

2 1/8” (54mm)

 

Width:

 

 

 

9 5/8” (244mm)

 

Frequency Response, ± 0.5 dB:

 

 

 

20 Hz - 20 kHz

 

Signal-to-Noise Ratio:

 

 

>95 dB, a-weighted, re: rated power

Input Sensitivity:

 

 

125 mV - 5 V low level, 250 mV - 10 V high level

Electronic Crossover:

 

 

Variable HI, LO or OFF (bypass), 50 - 200Hz, 12dB per octave

Bass Boost:

 

 

Variable 0 to +18 dB boost @ 40 Hz

 

 

 

 

 

 

 

 

 

Model ZX350.2

 

 

 

 

 

110 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)

 

 

 

Signal to Noise Ratio -98 CEA-2006 (ref: 1W, A-weighted)

 

 

 

Model ZX450.2

 

 

 

 

 

150 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)

 

 

 

Signal to Noise Ratio -95 CEA-2006 (ref: 1W, A-weighted)

 

 

 

Model ZX550.2

 

 

 

 

 

205 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)

 

 

 

Signal to Noise Ratio -95 CEA-2006 (ref: 1W, A-weighted)

 

 

 

Model ZX850.2

 

 

 

 

 

295 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)

 

 

 

Signal to Noise Ratio -93 CEA-2006 (ref: 1W, A-weighted)

 

 

 

 

 

 

PERFORMANCE

4

ZX.2AMPLIFIER

5

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Stereo Amplifier Allation Installation . . . as easy as 1, 2Configuration The following Congratulations on your Kicker purchasePerformance TroubleShootingOperation OperationInstale un fusible dentro de 18 45 cm de Configu¡Felicidades por su compra de Kicker Instalación tan fácil como 1, 2 yRendimiento Resolución de ProblemasOperación OperaciónBenutzung der Passive crossover. Siehe Abbildung Installation . . . in 3 Schritten 1, 2Herzlichen Glueckwunsch zum Kauf des Kicker EinstellungenInbetriebnahme InbetriebnahmeFélicitations pour votre achat Installation . . . aussi simple que 1, 2Configuration InstallationRéglage de gain dentrée Résolution des ProblèmesOpération OpérationHOW Long will IT TAKE? ElectronicsLimitedWarrantyInternationalWarranty What is not COVERED?

ZX850.2, ZX550.2 specifications

The Kicker ZX series amplifiers, specifically the ZX850.2 and ZX550.2, are integral components for audiophiles looking to enhance their sound experience. Renowned for their combination of power, efficiency, and advanced technology, these amplifiers offer exceptional performance for both novice and expert users alike.

The Kicker ZX850.2 is a powerful two-channel amplifier that delivers an impressive 850 watts of peak power. With the ability to provide 425 watts per channel at 2 ohms, it is designed to work seamlessly with a range of speakers, allowing for remarkable sound clarity and punchy bass. This amplifier is equipped with a variable high- and low-pass crossover, enabling users to tailor the sound to their specific preferences. Additionally, the inclusion of a bass boost feature helps enhance low-frequency performance, making every beat resonate.

On the other hand, the ZX550.2 provides 550 watts of peak power, delivering 275 watts per channel at 2 ohms. This model is ideal for those who want a compact yet powerful solution. Its compact design allows for flexible installation options without compromising on performance. Like its larger counterpart, the ZX550.2 also features adjustable crossover settings and a bass boost function, allowing users to achieve their desired audio profile effortlessly.

Both the ZX850.2 and ZX550.2 utilize Kicker's proprietary technologies to ensure high-quality sound reproduction. The amplifiers are designed with a Class D topology, which enhances efficiency and minimizes heat production. This allows the amplifiers to maintain excellent sound quality even when pushed to their limits. Moreover, the built-in thermal protection circuitry helps preserve the longevity of the amplifier, preventing overheating and ensuring reliable operation.

The compact chassis of both amplifiers is constructed from durable materials and features a stylish finish, ensuring they not only perform well but also complement the aesthetics of any vehicle’s interior. The terminal connections are designed for easy installation, making it simpler for users to integrate these amplifiers into their sound systems.

Overall, the Kicker ZX850.2 and ZX550.2 amplifiers stand out in the market for their robust power output, advanced features, and user-friendly design, making them excellent choices for anyone looking to elevate their audio experience. Whether for a casual listener or a dedicated enthusiast, both models deliver superior sound quality that enhances any music genre.
Top Page Image Contents