TROUBLESHOOTING
You can solve many common air conditioner problems easily, saving you the cost of a service call. Try the suggestions below to see whether you can solve your problem without outside help.
Air conditioner will not operate.
■The power supply cord is unplugged. Plug into a grounded 3 prong outlet. See “Electrical Requirements.”
■A household fuse has blown or circuit breaker has tripped. Replace the fuse or reset the circuit breaker. Plug into a grounded 3 prong outlet. See “Electrical Requirements.”
■The Fan control is turned to the off position. Turn the FAN control to an active setting.
■The local power has failed. Wait for power to be restored.
Air conditioner blows fuses or trips circuit breakers.
■Too many appliances are being used on the same circuit. Unplug or relocate appliances that share the same circuit.
■
■An extension cord is being used. Do not use an extension cord with this or any other appliance.
■You are trying to restart the air conditioner too soon after turning the Fan control off. Wait at least 3 minutes after turning the Fan control off before trying to restart the air conditioner.
Air conditioner seems to run too much.
■The current air conditioner replaced an older model. The use of more efficient components may cause the air conditioner to run longer than an older model, but the total energy consumption will be less. Newer air conditioners do not emit the “blast” of cold air you may be accustomed to from older units, but this is not an indication of lesser cooling capacity or efficiency. Refer to the efficiency rating (EER) and capacity rating (in BTU/h) marked on the air conditioner.
■The air conditioner is in a heavily occupied room, or heat- producing appliances are in use in the room. Use exhaust vent fans while cooking or bathing and try not to use heat- producing appliances during the hottest part of the day. A higher capacity air conditioner may be required, depending on the size of the room being cooled.
Air conditioner cycles on and off too much, or does not cool/heat room in cooling/heating mode.
■The Fan control is set to POWER SAVER (on some models). Use Power Saver only when you are away from home or asleep, since the fan does not circulate the room air continuously. Use LOW COOL, HIGH COOL or TURBO COOL for your best comfort.
■The air conditioner is not properly sized for your room. Check the cooling capabilities of your room air conditioner. Room air conditioners are not designed to cool multiple rooms.
■The filter is dirty or obstructed by debris. Clean the filter.
■The inside evaporator and outside condenser coils are dirty or obstructed by debris. See “Annual Maintenance.”
■There is excessive heat or moisture (open container cooking, showers, etc.) in the room. Use a fan to exhaust heat or moisture from the room. Try not to use heat- producing appliances during the hottest part of the day.
■The louvers are blocked. Install the air conditioner in a location where the louvers are free from curtains, blinds, furniture, etc.
■The outside temperature is below 65°F (18°C). Do not try to operate your air conditioner in the cooling mode when the outside temperature is below 65°F (18°C).
■The temperature of the room you are trying to cool is extremely hot. Allow extra time for the air conditioner to cool off a very hot room.
■Windows or doors to the outside are open. Close all windows and doors.
■The Exhaust control is set to OPEN (on some models). Set the Exhaust control to CLOSED for maximum cooling and/or heating.
■The Thermostat control is not at a cool enough setting. Adjust the THERMOSTAT control to a cooler setting by turning the knob clockwise. Turn the FAN control to TURBO COOL.
■The air conditioner in the heating mode has insufficient BTUs/hr for the heating requirements of the room. Do not use the air conditioner as a primary source of heat.
Water drips from cabinet into your house.
■The air conditioner is not properly leveled. The air conditioner should slope slightly downward toward the outside. Level the air conditioner to provide a downward slope toward the outside to ensure proper drainage. See the Installation Instructions.
NOTE: Do not drill a hole in the bottom of the metal base and condensate pan.
12