Axis Communications P1343-E user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD card

Page 46

AXIS P1343-E Network Camera

System Options

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 40. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to factory default settings, on page 49.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD card

The SD/SDHC memory card (not included) is managed on the System Options > Storage page. Click SD card to open Storage Management.

Mounting is done automatically when the card is inserted or when the product boots. SD cards are normally preformatted when purchased, but if needed, click Format to format the card.

Format an SD card so that it can be written to one of two available options — VFAT and ext4. During the formatting any previous data stored on the disk will be lost. The recommended format is ext4, due to its resilience against data loss if the card is ejected or if there is abrupt power loss. A third-party ext4 driver or application is also needed to access the file system from Windows.

Note that most SD cards are pre-formatted with vFAT when purchased. The Check Disk option is used to check for errors on the SD card and only works for the file system ext4. The Repair option repairs the SD card of errors in the file system ext4. For vFAT file system use a card reader or PC to perform card maintenance.

Note

To prevent corruption of recordings, the SD card should always be unmounted before removal.

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Axis P1343-E Network Camera Intellectual Property Rights About this documentLiability Equipment ModificationsTable of Contents Axis P1343-E Network CameraTechnical Specifications Hardware overview Hardware overviewAxis P1343-E Network Camera Connectors Function Pin Specifications GNDMaintenance LED indicatorsStatus LED when using Focus Assistant Replacing the lensAttach and screw on the new lens Accessing the product Accessing the productAccess from a browser Network TCP/IP Advanced Access from the InternetSet the root password Click Create self-signed certificateLive View Controls on the Live ViewPTZ Controls Axis Media Control viewer toolbarAMC Audio controls Axis P1343-E Network Camera Media streams How to stream H.264Media streams Axis Media Control AMCAlternative methods of accessing the video stream Accessing audio streams Setting up the product Setting up the productBasic Setup Video Stream Video and AudioVideo and Audio Pixel CounterImage Stream Profiles264 Image Appearance Camera SettingsExposure Settings White balanceView Area OverlayFocus Audio SettingsPrivacy Mask Audio ChannelsAudio Input G711 G726Audio Clips Audio OutputLive View Config Default viewer for browsersLive View Config Output Buttons Viewer SettingsUser Defined Links Browser Viewer DescriptionPTZ Pan Tilt Zoom Preset PositionsPTZ Pan Tilt Zoom Guard TourAdvanced ControlsCamera Tampering DetectorsDetectors Motion DetectionSet up motion detection Motion detection parametersRecommended values Default valuesAudio detection Go to Detectors Audio DetectionApplications ApplicationsEvents Setting Up an Action RuleEvents Convert Event Types to Action RulesSchedules RecipientsRecurrences Axis P1343-E Network Camera Recording List RecordingsRecordings Continuous recordingAxis P1343-E Network Camera Security System OptionsSystem Options UsersIeee Date & TimeAudio Support IPv4 Address Configuration Basic TCP/IP SettingsNetwork IPv6 Address ConfigurationAdvanced TCP/IP Settings Link-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service Smtp emailRTP/H.264 StorageUPnPTM BonjourNetwork Share MaintenancePorts & Devices PortsSystem Overview SupportSupport Overview Logs & ReportsFile Upload Reset to factory default settingsScripting Plain ConfigAxis P1343-E Network Camera Emergency recovery procedure TroubleshootingTroubleshooting Checking the firmwareProblems setting the IP address Symptoms, possible causes and remedial actionsProduct cannot be accessed from a browser Problems with the H.264 format Product is accessible locally but not externallyStatus and Network indicator LEDs are flashing red rapidly Problems uploading files Video and image problems, generalSetup Video & Audio Camera Settings No images displayed on webNo audio SettingsStorage and disk management problems Poor audio qualityTechnical Specifications Technical SpecificationsConnectors Maintenance Installation aidsMemory Power Network SecurityPerformance considerations M1.8
Related manuals
Manual 142 pages 36.45 Kb
Top Page Image Contents