Bosch Appliances LTC, 8500 AC Line Fuse Replacement, Power Supply Fuse Replacement

Page 76

18.3 AC Line Fuse Replacement

The AC line fuse on Allegiant power supply models is found on the rear of the equipment bay near the line cord connector. Power supply models for 220-240 VAC input version may contain a circuit breaker equipped power switch which can be reset directly from the front. If the line fuse needs to be replaced in a 120 VAC model power supply, remove the line cord from the system. Insert a flat blade screwdriver into the slot located at one end of the connector housing and rotate the screwdriver until the door to the housing opens. Remove fuse holder from housing as shown in drawing.

! !

Fuse Removal

Fuse

Removal

!

Figure 14: Allegiant power supply AC line fuse

Remove fuse from holder and replace with fuse of same rating for continued protec- tion. Reinstall fuse holder into connector housing in the same orientation as indi- cated by the arrow on the door cover. Snap door closed. After replacing fuse, verify system start-up and operation.

18.4 Power Supply Fuse Replacement

The main power supply is located in the far right side of the equipment bay. Remove the front panel of the bay by loosening the four fasteners. Locate the fuse to be replaced by observing the green LED indicators. Note which LED indicators are not lit, then turn OFF the main power switch located on the power supply. Replace fuses associated with LEDs which were not lit. Switch on the main power switch and verify that all LEDs are now lit. Replace front panel.

18.5 Replacement of Memory Backup Batteries

CAUTION

Lithium batteries should be replaced by qualified service personnel only.

 

The memory backup batteries are located on the main CPU card located next to the

 

power supply module in the main CPU bay. The batteries provide RAM memory

 

backup for a period of at least one year. They are only active when main AC power

 

to the system has been lost. The RAM memory is used to store system operational

 

data which is frequently changing, including time/date and system crosspoint data

 

(i.e., which camera is currently being displayed on which monitor). More vital sys-

 

tem data such as camera titles, alarm settings, user information and passwords, etc. is

 

stored in non-volatile memory that is not affected by the condition of the batteries or

 

the main AC power.

 

Remove the front panel of the main CPU bay by loosening the four fasteners. The

 

two batteries are mounted on the front edge of the CPU card and are about 25 mm

 

(1 in.) in diameter. Insert a small flat blade screwdriver into the slot on one of the

EN 66

Bosch Security Systems December 13, 2005

Image 76
Contents Bosch LTC 8500 SeriesBosch Security Systems December 13 Important Safeguards For Outdoor Product For Indoor ProductFor Rack-mount Product Sicherheitshinweise SécuritéPrecauciones de Seguridad Veiligheidsmaatregelen Medidas de Segurança SicurezzaPage Bosch Security Systems December 13 Page Bosch Security Systems December 13 Unpacking Parts ListQty Service USADescription Bosch Security Systems December 13 Allegiant Feature Summary Table Bosch Security Systems December 13 LTC 8501 Series Systems System ComponentsLTC 8501 Series Systems System Accessory Components LTC 8540/00 Alarm Interface UnitLTC 8568 and LTC 8768 Signal Distribution Units IntuiKey Series KBD-Universal KeyboardLTC 8555 Series Keyboards LTC 8558/00 Keyboard Extension CableLTC 8557 Series Keyboard Extension Kits LTC 8560 and LTC 8561 Series Receiver/Driver UnitsLTC 8713 Alarm Port Expander Units LTC 8770 Switcher Follower SeriesLTC 8712 Series Console Port Expander Units LTC 8780 Series Data Converter Units LTC 8781 Series Data Converter UnitsLTC 8016/90 Bilinx Data Interface Unit LTC 8785 Series Code ConvertersLTC 8059/00 Master Control Software LTC 8850/00 Windows Based Graphical User Interface SoftwareSFT-INTSRV Allegiant Integration Software Integration ServerAllegiant Satellite Software Development Kit LTC 8506/00 PC-to-Console Port RS-232 CableLTC 8506/00 PC-to-Console Port RS-232 Cable Logging Printer LTC 8500 Series Video Switching ConfigurationTion provided at the end of this manual Data Main CPU Bay Installation Installation ProcedureVideo Input Modules CPU Module Video Output ModulesVideo Output Modules Camera and Monitor Video Connections Termination PracticesLTC 8500 Series Video Terminations Monitor Output Video ConnectionsOptional Accessories Installation General Accessory InstallationLogging Printer Option Installation Procedures not coveredComputer Interface Installation ComputerSatellite Site Trunk Line Monitor Outputs Satellite Configuration InstallationsSatellite Site Trunk Line Monitor Outputs Control Data Lines in Satellite Systems Main Site Trunk Line Video InputsSatellite Site Programming Requirements Main Site Programming Requirements Main Site Programming RequirementsMing of the main site via a system keyboard Page Alarm Inputs in Satellite Systems Feature Selection Alarm Inputs in Satellite SystemsMain Power Connections LTC 8501 Series Rear PanelVideo Monitor Display Time / DateMonitor Title/System Status Display Monitor MessageSystem Status Display Monitor Title/System Status Display Bosch Security Systems December 13 Factory Default Settings User Selectable DIP Switch Settings for Main CPU BayUpper CPU DIP Switch S1001 User Selectable DIP Switch Settings for Main CPU BayLower CPU DIP Switch S1002 Keyboard model Supported protocols Drivers without using an LTC 8785 Series Code Converter unit Boards are initially logged-offSettings Console Port Printer Port Alarm Port Keyboard Ports User Information User Priority LevelsUser Priority Access Table User Priority Access TableSystem Function Alarm Information Basic Alarm Response ModeAuto Build Alarm Response Mode Sequence and Display Alarm Response ModeSample Alarm Responses Alarm Activated Pre-positionAlarm Activated Pre-position None Alarm Relay Response Alarm Relay ResponseSystem Commands Keyboard Log-in ProcedureKeyboard Operation IntuiKey button textSwitcher Commands Controlling Camera MovementAlarm activations are defaulted to call preposition scene Lock or Unlock Control of a MonitorRecording a Camera Pre-position Scene Recalling a Camera Pre-position SceneArm/Disarm Individual Alarms Alarm CommandsAlarm Commands Arm/Disarm All Alarms Alarms AcknowledgementSequence Control Arm/Disarm MonitorRun a Sequence Stop a Running SequenceControlling Sequence Direction Sequence ControlSequence Programming Programming a Simple Camera SequenceSequence Programming Sequence Function SummaryKey Description Programming a SalvoSwitching Camera Sequence Camera Monitor DwellGeneral Information Keyboard User FunctionsGeneral Information These functions are listed in the table shown below User Function 1 Local Keyboard Test KeyUser Function 4 Adjust Position of Monitor Overlay User Function 2 Show Keyboard Port NumberUser Function 3 Select Keyboard Beeper ON/OFF User Function 6 Select Monitor Display OptionUser Function 10 Change User Password User Function 7 Set TimeUser Function 8 Set Date User Function 9 Set Camera IDUser Function 12 Default All Monitor Overlays User Function 13 Print System Configuration TablesUser Function 16 Time Event Enable/Disable User Function 11 Select Time / Date FormatUser Function 19 Select Alarm Response User Function 21 Designate Alarm Monitor TypeUser Function 18 Print Sequence User Function 20 Select Printer VerbosityUser Function 23 Display CPU Software Version Number User Function 24 Set Positions on All Monitor DisplaysUser Function 25 Set Brightness on All Monitor Displays User Function 26 Set Display Option On All MonitorsUser Function 29 Reset RS-232 Parameters to Default User Function 32 Set Alarm RS-232 ParametersUser Function 28 Select Console Log-in User Function 30 Set Console RS-232 ParametersUser Function 34 Camera Indicator User Function 37 R/D Address ModeUser Function 38 Printer Port Mode User Function 35 Controllable CamerasGeneral Information User Function 43 CPU Battery Status User Function 42 Keyboard Log-in Auto-off ModeUser Function 99 User Function Index Maintenance Information Cleaning the KeyboardCleaning the Keyboard AC Line Voltage Input SelectionPower Supply Fuse Replacement AC Line Fuse ReplacementReplacement of Memory Backup Batteries Replacement of Memory Backup Batteries Character ROM Tables for LTC LTC 8500 Character ROM Table Error Messages Replacement of Memory Backup Batteries Bosch Security Systems December 13 Troubleshooting Guide Main Bay CheckoutKeyboard Checkout Main Bay CheckoutVideo Monitor Display Checkout No Alarm ResponseRemote Receiver/Driver Functions Inoperative CPU Software Version Numbers CPU Software Version NumbersGlossary of Terms CPU Software Version Numbers Appendix a Satellite Systems Allegiant Satellite Concepts Model No Maximum Number System Cameras CPU Software Version Numbers Conceptual Diagram of Allegiant Satellite Switching System Conceptual Diagram of Allegiant Satellite Switching SystemConceptual Diagram of Dual Master Allegiant Satellite System Conceptual Diagram of Cascaded Allegiant Satellite System Conceptual Diagram of Cascaded Allegiant Satellite SystemAppendix B Installation Checklists Main BAY Hardware InstallationAlarm Interface Unit Appendix C Quick Reference Cable InterconnectionsMain Bay Video KeyboardsSignal Distribution Unit Receiver/DriversMain Bay Rear Panel Connector Pin-outs and Cable Pin-out Alarm Port RS-232 Pin-outsConsole Port RS-232 Pin-outs Keyboard RS-485 PortsCPU Software Version Numbers Code Port Pin-outs Comm Port 1 and Comm PortCTS RTS Page Bosch Security Systems December 13 Page Europe, Middle East, Africa Asia-Pacific