DMP Electronics SCS-1R manual Model SCS-120 Multibus Power Supply Card, Installing the SCS-120

Page 17

Installation

Model SCS-120 Multibus Power Supply Card

Description

The SCS-120 provides power to the SCS-150 through the multibus backplane. The SCS-120 also monitors the SCS-150 condition, the SCS-110 Modem Power Supply Card voltage output, and its own internal voltages.

Installing the SCS-120

Always disconnect power to the SCS-1R Receiver when installing or removing the SCS-120. Slide the SCS-120 Multibus Power Supply Card, the component side up, into the multibus rack upper position, which is the lower rack in the SCS-RACK.

Connect the SCS-208 Power Cable to J3 on the card front right side. Connect the other end of the power cable to the SCS-130 Transformer Card on the back of the modem rack. The power cable can be used in either direction.

Processor Monitor

������� ���� ��

��������

���

��

����� ����� ������� ���� �� ���� �� ���� ������� ����� ���� �� ��� ���

The SCS-120 monitors the Model SCS-150 processor through the multibus backplane. The green OK LED lights when the processor operates. If the processor stops operating, the red FAIL LED lights and the SCS-120 failure buzzer sounds.

Press the processor restart button to restart the system, silence the buzzer, and turn off the red LED. The restart button restarts the system.

Power Monitor LEDs

The SCS-120 monitors three different system voltages, +5, +12, -12 and the modem power supply. Four LEDs located to the right of the power alert silence switch display any voltage failures. A green OK LED lights when the voltages are working properly. The green PWR LED for the modem power supply is located on the SCS-110 Modem Power Supply Card. The red TRBL LED lights and the trouble alert tone on the SCS-120 sounds when there is a problem with a voltage level.

Press the SCS-120 power alert silence switch to silence the alert tone. The red TRBL LED remains lit until the power problem is corrected. The modem power LED, the SCS-120 trouble alert tone, and the SCS-110 Modem Power Supply Card power alert LED all operate together.

Digital Monitoring Products

SCS-1R Installation Guide

12

Image 17
Contents DMP Receiver Help Line Installation GuideIndustry Canada Notice Security Control Receiver Model SCS-1R Installation GuideOperator’s Quick Reference Installation ChecklistSystem Overview Model SCS-1R Security Control ReceiverModel SCS-120 Multibus Power Supply Card Model SCS-110 Modem Power Supply CardModel SCS-208 Power Cable Security Control Terms Using the LCD Membrane KeypadPrinter Troubleshooting LCD Membrane Keypad ConfigurationComponents Accessory Devices Listings and Approvals Status Displays and SCS-1R ProgrammingOperator’s Quick Reference Acknowledging an Alarm SignalLED Indicators System Overview Cable A3 Cable A2 Cable A1 Model SCS-203 Convenience Panel System Block DiagramInstallation Checklist SCS-1R Components Included Model SCS-1R Security Control ReceiverModel SCS-RACK System Enclosure Installing the SCS-RACKModem Rack Multibus RackModel SCS-150 Receiver Processor Board Clearing Receiver Events Software Update Using the SD CardReset Programming To Factory Defaults Model SCS-100 Line Card SCS-101 Data Jumper Settings Installing the SCS-101Model SCS-101 Network Interface Card CommunicationModel SCS-110 Modem Power Supply Card Processor Monitor Model SCS-120 Multibus Power Supply CardInstalling the SCS-120 AC Power Connection InstallationModel SCS-130 Transformer Card Three Amp FuseModel SCS-203 Convenience Panel Model SCS-208 Power CableModel SCS-204 Host Cable SCS-1R Printer CableSecurity Control Terms ULC Installation RecommendationsSpecial Keys Using the LCD Membrane KeypadKeypad Prompts Display Current Programming Entering Alpha CharactersKeypad Options and Diagnostics LCD Membrane Keypad ConfigurationInternal Speaker Operation LCD BacklightingDefault Keypad Message Keypad ModeAccessing Keypad Diagnostics Keypad Diagnostics KPD DiagReceiver Startup Display Status Displays and SCS-1R ProgrammingTime Display Off-Normal StatusProgramming Through Remote Link Service Code XR500 Series panelsProgramming Menu Receiver OptionsLine Cards Serial Ports Host AutomationExit Programming Menu Set System Time/DatePrintout Explanations Door Access Printer TroubleshootingAcknowledgment of Fire Alarms and Troubles Message DestinationsImportant Information Accessory DevicesComponents Listings and Approvals