Harman Stove Company HB 38 DV manual Installing the Floor Register

Page 33

Only For Qualified Installers

INSTALLATION (Options)

Installing the Floor Register

Breakoff Tabs

Tilt Blower Box

Mounting Screws

The blower box mounting bracket is designed to allow mounting into an existing floor. However, it is easier to in- stall all components at the time of house

construction. The mounting bracket as- sumes that floor joists are on 16” cen-

ters. The mounting bracket has break-off tabs that are to be left on only if the floor joists are too far apart to be reached with- out them. To break off the tabs simply bend them back and forth until they break. The following instructions are for installing in an existing floor.

1.Cut a 71/2 x 137/8 hole in the floor at the proper location. The hole must be perpendicular to the floor joists.

2.Place the mounting bracket in the hole as shown. The tapered end of the bracket must be opposite to the side where the air will enter the blower box.

3.Place the blower box with blower assembly removed, down into the bracket, angling it as shown. Slide the blower box down into the bracket as far as needed to tilt it level. Then slide the box in position and attach the duct work (not shown). Install the box mounting screws.

4.Insert the electrical wires for the blower into the box through one of the two holes provided.

5.Using wire nuts, connect the wires to the motor and speed control as shown on the wiring diagram.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Harman Built Serenity HB 38 DV Safety NoticeForyour Safety Table of Contents Introduction Air Gate Blower System 200% To 300% More Air Important FeatureBlower Off Blower OnOperation OperationPilot Flames HOW to Turn OFF the FireTop Vent Rear Vent SpecificationsThis fireplace may be placed on a wood floor Minimum Clearances from Combustible ConstructionRear Vent Corner Top Vent Installation Installation OptionsTypical Tile Facing Sectional View Placement InstallationNoncombustible Removing The Arch Face Installing The Arch FaceAssembling the Victorian Face Installing Fireplace To use Victorian Face Mounting The Victorian Face Making The Connection Burn Only the Fuel for which the Heater is EquippedGas Pressure Requirements Natural GasUse Only Approved Venting Part Numbers for SimpsonDura-Vent Pipe and Fittings8 x Description Venting with 8 x 5 Pipe VentingRear Vent Model Approved. Never used 6 5/8 x 4 pipe for rear VentVenting with 6 5/8 x 4 Pipe Into a wallor siding Feet 2 to Damper SettingsChanging to LP LP Conversion KitTop Vent LP Kit Rear Vent LP Kit Vent Natural Top RearFront Rear Log Placement Connecting Optional Thermostat Installation OptionsRegister Kit Optional Remote Register KitFloor Kit Wall KitOptional Wall Register Kit Installing Damper AssemblyMount register after drywall and painting are finished Floor Register Installation Installing the Floor Register Fireplace is turned off and cools Not allow the register blower to start ifCleaning the Glass MaintenanceCleaning the Log Set and Firebox Removing the Glass FrontCleaning the Burners Air FlowLubrication Maintenance Verify proper operation after servicing WHI # Replacement Parts Propane Natural GasYes Trouble ShootingBad Replace Pirzo Ignitor Turn on gas valve Replenish supplyGood Pilot does not stay litCheck inlet pressure Correct inlet pressureIs Pilot lit Rear burner does not light Bad Install new batteriesCheck batteries Replace solinoidLife Time

HB 38 DV specifications

The Harman Stove Company HB 38 DV is a high-performance direct vent pellet stove that is designed to meet the needs of homeowners seeking efficient and effective heating solutions. This stove is renowned for its combination of advanced technology, sleek design, and user-friendly features, making it a popular choice for both aesthetic appeal and functional heating.

One of its key features is the patented Harman burn pot design, which ensures an even burn and maximum heat output. The burn pot is engineered to minimize clinkering, allowing users to enjoy longer burn times and less frequent maintenance. The HB 38 DV not only heats efficiently but does so while using environmentally friendly wood pellets, promoting a sustainable approach to home heating.

The stove is equipped with an advanced microprocessor-controlled smart technology system. This system automatically adjusts the burn rate to match the desired temperature settings, providing optimal comfort while maintaining energy efficiency. Users can simply set their desired temperature, and the stove will automatically adjust the feed rate and combustion air to maintain that level, reducing the need for constant adjustments.

The Harman HB 38 DV also features a large viewing window, providing an inviting visualization of the flames while contributing to the room's ambiance. The stay-cool handle allows for ease of opening the door without the risk of burns. The stove is available in several finishes allowing homeowners to select a style that complements their decor.

In terms of efficiency, the HB 38 DV boasts an impressive efficiency rating of over 85%. This means that more of the fuel is converted into usable heat, leading to reduced heating costs and fewer emissions. The unit has a powerful blower that effectively distributes heat throughout the room, ensuring that the warmth is felt quickly and evenly.

The installation process is flexible due to its direct vent capability, allowing for venting through walls or ceilings. This feature enables users to install the stove in various locations within their home, maximizing both functionality and style.

In summary, the Harman Stove Company HB 38 DV combines advanced technology, efficient heating, and modern design, making it a standout option for homeowners looking for a dependable and attractive pellet stove. Its various features cater to both performance and aesthetic preferences, positioning it as a leading choice in contemporary heating solutions.
Top Page Image Contents