Heat & Glo LifeStyle BAY-40 owner manual Mantel, Glass Doors

Page 29

C. Mantel

A combustible mantel may be positioned no lower than 12 in. (305 mm) above the top of the fireplace opening. The combustible mantel may have a maximum depth of 12 in. (305 mm). Combustible trim pieces that project no more than 1-1/2 in.(38 mm) from the face of the fireplace can be placed no closer than 6 in. (152 mm) from the top of the fireplace opening. See Figure 8.4. Combustible trim must not cover the metal surfaces of the fireplace. This mantel clearance is in accordance with Section 7-3.3.3 of ANSI/ NFPA211.

WARNING

Fire Risk

Do NOT obstruct air inlets.

Finishing materials must not interfere with:

•Air flow through inlets

•Operation of doors

•Access for service

D.Sidewalls/Surrounds

Adjacent combustible side walls must be located a minimum of 12 in. (305 mm) from the fireplace opening. If you are us- ing a decorative surround constructed of combustible ma- terial, it must be located within the shaded area defined in Figure 8.5. Short stub walls are also acceptable if they are contained within the shaded area.

E. Glass Doors

This fireplace has been tested and listed with doors (re- quired). See Section 12B Fireplace Components for avail- able doors. Please refer to the manual packed with each set of doors for installation instructions.

 

12 in. (305 mm)

 

 

 

 

max.

 

1-1/2 in. (38 mm) max.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Header

Mantel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Standoff

12 in. (305 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

min.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Top of

Fireplace

Opening

6 in. (152 mm) min.

Figure 8.4 Mantel Specifications

 

 

 

62 in.

 

 

 

12 in.

 

 

 

 

 

 

 

 

 

 

 

(305 mm)

 

 

 

(1575 mm)

 

 

72 in.

 

16 in.

 

 

from opening

 

 

 

 

 

 

 

of fireplace

 

 

(1829 mm)

 

(406 mm)

 

 

 

 

 

 

 

16 in.

(406 mm)

40-1/2 in.

56 in.

(1029 mm)

(1422 mm)

 

26 in.

6 in.

 

(660 mm)

(152 mm)

HEARTH

to front of

HEARTH

EXTENSION

fireplace

EXTENSION

(shaded)

opening

(shaded)

BAY-40

64 in.

PIER-40

64 in.

(1626 mm)

(1626 mm)

Figure 8.5 Sidewalls/Surrounds

WARNING

Fire Risk

Finish all edges and fronts to clearances and specifications.

•Metal fireplace front may be covered with non-combustible material only.

•Do NOT overlap combustible materials onto fireplace front.

•Install combustible materials up to specified clearances on top front and side edges.

•Seal joints between the finished wall and fireplace top and sides using only a 300° F minimum sealant.

Heat & Glo • Multi-Sided Woodburning Fireplace • 34977 Rev T • 11/07

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Fire Risk Hot glass will cause burnsNumber Listing Label Information/LocationGrate Table of Contents Not intended for use as a primary heat source Listing and Code ApprovalsAppliance Certification Getting Started Design and Installation ConsiderationsNegative Pressure Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemFire Risk Explosion Risk Tools and Supplies NeededInspect Fireplace and Components Selecting Fireplace Location Framing and ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements Construct the ChaseInstall the Outside Air Kit Installation of FireplaceSharp Edges Asphyxiation Risk Risk of Smoke SpillageFt min. from top of uppermost chimney section to air inlet Position the Fireplace Secure the FireplacePlace the Protective Metal Hearth Strips Level the FireplaceChimney Assembly Height of Chimney Components SL1106 SL1112 SL1118 SL1136 SL1148 Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsAway from chimney pipe may cause fire ¨E. Install the Attic Insulation ShieldSecure the Chimney Double-check the Chimney AssemblyChimney Termination Requirements See Figures 6.1 Complete the EnclosureChimney Termination Install the Chimney Air Kit required in Canada Install the Roof FlashingMark the Exit Point of the Roof ¨ Cut Out the Hole in the RoofChase Top Install the Termination CapInstalling an ST1175 Square Termination Cap Gas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provisions ¨ Table FinishingHearth Extension Non-Combustible Material Finishing MaterialCombustible Material Glass Doors MantelGeneral Information Operating InstructionsClear Space Near the Fireplace Outside AirFlue Damper FirescreenWood Fuel GrateFirewood MoistureStarting a Fire Understanding Vent Problems TroubleshootingDiagnostic Questions Diagnostics and Problem SolvingSolutions Can’t get a good fire going. What am I doing wrong?fireplace burns the wood too fast. What can I do? Chimney Inspection/Cleaning Maintenance and Servicing the FireplaceDisposal of Ashes Firebox RefractoryWhen cleaning glass door Maintenance Task ListClean Chimney FireReference Materials Fireplace DimensionsCatalog # Description Fireplace ComponentsCatalog # Chimney Components14-1/2 15-3/4 400 mm European Copper Caps Minimum Base Dimensions 26.5 X 28 with 34 X 34 with Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 XTR442 TR442 / 444 TV 20 xBAY-40 Service PartsGR3 Description of Part Part Number Qty.reqPIER-40 Qty # Description of PartThis page intentionally left blank Limited Warranty Warranty For Heat & GLO FireplacesDo not Discard this Manual

BAY-40 specifications

The Heat & Glo LifeStyle BAY-40 is a modern gas fireplace designed to deliver both style and functionality while enhancing the ambiance of any living space. Touted for its sleek design and advanced features, the BAY-40 serves as a centerpiece that combines warmth with contemporary aesthetics.

One of the most notable aspects of the LifeStyle BAY-40 is its impressive heat output, ensuring that rooms remain cozy even in the coldest months. With a variety of heat settings, users can easily adjust the temperature to their comfort level. This versatility makes it an ideal option for any home, whether for an expansive living area or a more compact setting.

The BAY-40 is equipped with an innovative IntelliFire technology that promotes ease of use and safety. This advanced ignition system eliminates the need for manual lighting, allowing users to start their fire at the push of a button. Additionally, the remote control feature offers convenience, enabling homeowners to control the fireplace from across the room, adding to the overall comfort factor.

Aesthetically, the LifeStyle BAY-40 is designed with a contemporary look in mind. Its large viewing area provides an unobstructed view of the flames, creating a warm and inviting atmosphere. The unique bay design not only enhances the visual appeal but also allows for a wider flame presentation, adding to the overall warmth of the room.

The fireplace also offers customizable options, such as different interior finishes and decorative media like glass or logs. These choices allow homeowners to tailor the fireplace to match their existing décor, contributing to a cohesive design throughout their home.

Moreover, the BAY-40 incorporates advanced safety features such as an automatic shut-off mechanism that activates in case of malfunction, ensuring peace of mind for users.

In summary, the Heat & Glo LifeStyle BAY-40 is more than just a fireplace; it’s a blend of innovation, design, and efficiency. Whether you are seeking to enhance your living space or provide warmth to your home, the BAY-40 stands out as an exceptional choice that balances modern technology with elegant aesthetics. Its range of features ensures both comfort and safety, making it a prime addition to any home.
Top Page Image Contents