Heat & Glo LifeStyle BAY-40 owner manual Getting Started, Design and Installation Considerations

Page 5

2 Getting Started

A. Design and Installation Considerations

CAUTION

Check building codes prior to installation.

•Installation MUST comply with local, regional, state and national codes and regulations.

•Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction about restrictions, installation inspection and permits.

When planning a fireplace installation, it is necessary to de- termine the following information before installing:

•Where the fireplace is to be installed. See Sections 3 and 4.

•The vent system configuration to be used. See Sections 5 and 6.

•Gas supply piping. See Section 7.

•Electrical wiring. See Section 7.

•Framing and finishing details. See Sections 3, 6 and 8.

•Whether optional accessories—devices such as a fan, wall switch or remote control—are desired. See Section 12.

Draft is the pressure difference needed to vent fireplaces successfully. Considerations for successful draft include:

•Preventing negative pressure

•Location of fireplace and chimney

WARNING

Asphyxiation Risk

Negative pressure can cause spillage of combustion fumes and soot. Fire needs to draft properly for safe operation.

B. Negative Pressure

Negative pressure results from the imbalance of air avail- able for the fireplace to operate properly. Causes for this imbalance include:

•Exhaust fans (kitchen, bath, etc.).

•Range hoods.

•Combustion air requirements for furnaces, water heaters and other combustion appliances.

•Clothes dryers.

•Location of return-air vents to furnace or air conditioning.

•Imbalances of the HVAC air handling system.

•Upper level air leaks: recessed lighting, attic hatch opening, duct leaks.

To minimize the effects of negative air pressure, the follow- ing must be considered:

•Install the outside air kit. Install the intake on the side of the house towards prevailing winds during the heating season.

•Ensure adequate outdoor air is supplied for combustion appliances and exhaust equipment.

•Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the fireplace.

•Avoid installing the fireplace near doors, walkways or small isolated spaces.

•Recessed lighting should be a “sealed can” design; attic hatches weather stripped or sealed; attic mounted duct work and air handler joints and seams taped or sealed.

•Basement installations should be avoided due to stack effect. Stack effect creates negative pressure in lower levels. Hearth & Home Technologies recommends the use of direct vent fireplaces in basements.

Heat & Glo • Multi-Sided Woodburning Fireplace • 34977 Rev T • 11/07

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Fire Risk Hot glass will cause burnsNumber Listing Label Information/LocationGrate Table of Contents Not intended for use as a primary heat source Listing and Code ApprovalsAppliance Certification Getting Started Design and Installation ConsiderationsNegative Pressure Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemFire Risk Explosion Risk Tools and Supplies NeededInspect Fireplace and Components Selecting Fireplace Location Framing and ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements Construct the ChaseInstall the Outside Air Kit Installation of FireplaceSharp Edges Asphyxiation Risk Risk of Smoke SpillageFt min. from top of uppermost chimney section to air inlet Position the Fireplace Secure the FireplacePlace the Protective Metal Hearth Strips Level the FireplaceChimney Assembly Height of Chimney Components SL1106 SL1112 SL1118 SL1136 SL1148 Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsAway from chimney pipe may cause fire ¨E. Install the Attic Insulation ShieldSecure the Chimney Double-check the Chimney AssemblyChimney Termination Requirements See Figures 6.1 Complete the EnclosureChimney Termination Install the Chimney Air Kit required in Canada Install the Roof FlashingMark the Exit Point of the Roof ¨ Cut Out the Hole in the RoofChase Top Install the Termination CapInstalling an ST1175 Square Termination Cap Gas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provisions ¨ Table FinishingHearth Extension Non-Combustible Material Finishing MaterialCombustible Material Glass Doors MantelGeneral Information Operating InstructionsClear Space Near the Fireplace Outside AirFlue Damper FirescreenWood Fuel GrateFirewood MoistureStarting a Fire Understanding Vent Problems TroubleshootingDiagnostic Questions Diagnostics and Problem SolvingSolutions Can’t get a good fire going. What am I doing wrong?fireplace burns the wood too fast. What can I do? Chimney Inspection/Cleaning Maintenance and Servicing the FireplaceDisposal of Ashes Firebox RefractoryWhen cleaning glass door Maintenance Task ListClean Chimney FireReference Materials Fireplace DimensionsCatalog # Description Fireplace ComponentsCatalog # Chimney Components14-1/2 15-3/4 400 mm European Copper Caps Minimum Base Dimensions 26.5 X 28 with 34 X 34 with Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 XTR442 TR442 / 444 TV 20 xBAY-40 Service PartsGR3 Description of Part Part Number Qty.reqPIER-40 Qty # Description of PartThis page intentionally left blank Limited Warranty Warranty For Heat & GLO FireplacesDo not Discard this Manual

BAY-40 specifications

The Heat & Glo LifeStyle BAY-40 is a modern gas fireplace designed to deliver both style and functionality while enhancing the ambiance of any living space. Touted for its sleek design and advanced features, the BAY-40 serves as a centerpiece that combines warmth with contemporary aesthetics.

One of the most notable aspects of the LifeStyle BAY-40 is its impressive heat output, ensuring that rooms remain cozy even in the coldest months. With a variety of heat settings, users can easily adjust the temperature to their comfort level. This versatility makes it an ideal option for any home, whether for an expansive living area or a more compact setting.

The BAY-40 is equipped with an innovative IntelliFire technology that promotes ease of use and safety. This advanced ignition system eliminates the need for manual lighting, allowing users to start their fire at the push of a button. Additionally, the remote control feature offers convenience, enabling homeowners to control the fireplace from across the room, adding to the overall comfort factor.

Aesthetically, the LifeStyle BAY-40 is designed with a contemporary look in mind. Its large viewing area provides an unobstructed view of the flames, creating a warm and inviting atmosphere. The unique bay design not only enhances the visual appeal but also allows for a wider flame presentation, adding to the overall warmth of the room.

The fireplace also offers customizable options, such as different interior finishes and decorative media like glass or logs. These choices allow homeowners to tailor the fireplace to match their existing décor, contributing to a cohesive design throughout their home.

Moreover, the BAY-40 incorporates advanced safety features such as an automatic shut-off mechanism that activates in case of malfunction, ensuring peace of mind for users.

In summary, the Heat & Glo LifeStyle BAY-40 is more than just a fireplace; it’s a blend of innovation, design, and efficiency. Whether you are seeking to enhance your living space or provide warmth to your home, the BAY-40 stands out as an exceptional choice that balances modern technology with elegant aesthetics. Its range of features ensures both comfort and safety, making it a prime addition to any home.
Top Page Image Contents