Heat & Glo LifeStyle AT-GRAND-D manual Maintaining 4Servicing Your Appliance Entretien et révision

Page 27

Maintaining and

 

4Servicing Your Appliance

Entretien et révision

Appliance Maintenance

Although the frequency of servicing and maintenance will depend on use and the type of installation, you should have a qualified service technician perform an appliance check- up at the beginning of each heating season. Specific guidelines regarding each appliance maintenance task are listed below.

IMPORTANT: TURN OFF THE GAS BEFORE SERVICING YOUR APPLIANCE.

Replacing old ember material

Frequency: Once annually, during the checkup.

By: Qualified service technician.

Task: Brush away loose ember material near the burner. Replace old ember material with new dime-size and shape pieces of Golden Ember (DE-93) and Glowing Ember (050- 721). New ember material should be placed alternately on top of the burner - a layer of Golden Ember, a layer of Glowing Ember, and so on. Save the remaining ember material and repeat this procedure at your next servicing. For more information, see Placing Ember Material in the Installers

Guide.

Cleaning Burner and Controls Frequency: Once annually. By: Qualified service technician.

Task: Brush or vacuum the control compartment, fireplace logs and burner areas surrounding the logs.

Checking Flame Patterns, Flame Height

Frequency: Periodically.

By: Qualified service technician/Home owner.

Task: Make a visual check of your fireplace’s flame patterns. Make sure the flames are steady - not lifting or floating. See Figure 14. The thermopile/thermocouple (standing pilot) tips should be covered with flame. See Figure 6.

Entretien

Bien que la fréquence d’entretien et de révision de la cheminée dépende du volume d’utilisation et du type d’installation, nous recommandons un examen de l’appareil par un technicien qualifié au début de chaque saison de chauffage. Voir le tableau ci-dessous pour les instructions d’entretien correspondant à chaque cheminée.

IMPORTANT: COUPER L’ALIMENTATION EN GAZ AVANT TOUTE OPÉRATION D’ENTRETIEN SUR CET

APPAREIL.

Remplacement des braises usagées

Fréquence: Une fois par an, lors de la révision saisonnière

Par: Technicien après-vente qualifié

Opération: Enlever les braises à l’aide d’une brosse à proximité du brûleur. Remplacer les braises usagées par du Golden Ember (GE-93) de la taille de pièces de 10 cents et du Glowing Ember (050-721).Alterner les couches de braises sur le brûleur, une couche de Golden Ember, une couche de Glowing Ember, et ainsi de suite. Conserver les braises restantes et répéter cette procédure lors de l’entretien suivant. Pour de plus amples informations, consulter la section Pose des braises dans le Guide d’installation.

Nettoyage des brûleurs et des commandes Fréquence: Une fois par an

Par: Technicien après-vente qualifié

Opération: Nettoyer au moyen d’une brosse ou d’un aspirateur le compartiment commandes, les bûches de la cheminée et les zones des brûleurs autour des bûches.

Vérification de la configuration des flammes et de la hauteur des flammes

Fréquence: Périodiquement

Par: Technicien après-vente qualifié/Propriétaire

Opération: Examiner visuellement la configuration flammes de la cheminée. S’assurer que les flammes sont stables, qu’elles ne montent ni ne flottent. Voir Figure 14. Les pointes des thermopile/thermocouple (veilleuse) doivent être cou- vertes par la flamme. Voir Figure 6.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Guide d’installation Safety and Warning Information Page Table of Contents Log Set Assembly Service PartsAccessories / Accessoires 1Approvals and Codes Approval Listing and CodesHomologations et codes Approvals and Codes Homologations et codes suite CES Situations Peuvent Créer DES Risques Pre-installation Preparation Avant l’installationANY Such Action MAY Possibly Cause a Fire HAZ ARDGetting Started Mise en marche suite Diagram of the AT-GRAND-D Installing the Insert Step Installing the Vent SystemÉtape Installation du système de ventilation Homologations Connecting the Vent PipeVent System Approvals Raccordement du conduit de ventilationMinimum Height from Roof to Lowest Discharge Opening Installing the Insert Installing the Insert Installation suite Gas Controls Systems DE Commande SUR 110-120 VCAStanding Pilot Ignition System Allumage par veilleuseFuites DE GAZ Avec UNE Flamme NUE Step Gas Supply LineÉtape 4 Raccordement au gaz Approved and/or licensed as required by the localityPression Gaz naturel Propane Step Gas Pressure RequirementsÉtape Spécifications relatives La pression du gaz Pressure Natural Gas PropaneGAS Control Valve or Advertissement NE PAS Raccorder LATout Fonctionne Normalement Étape Pose des bûches et des braises Step Installing Logs and Ember MaterialDéposer la porte Glass Assembly Porte en verrePlacement Pose des braises Ember Material Lift the top trim door upLA Porte ET LA Porte EN Verre DE L’APPAREIL DE Chauffage Avant D’INSTALLER L’ENCADREMENTAvertissement Lors DE LA Finition DE Remarque Déposer L’ENCADREMENT Frontal DEMARCHE/ARRÊT Step Lighting the Appliance After the InstallationAprès l’installation Step Before Lighting the ApplianceChecking Flame Patterns, Flame Height Remplacement des braises usagéesMaintaining 4Servicing Your Appliance Entretien et révision Replacing old ember materialAbrasive cleaners Cleaning Glass DoorAttempt to clean the door When it is hot and do not use

AT-GRAND-D specifications

The Heat & Glo LifeStyle AT-GRAND-D is an impressive gas fireplace that combines advanced technology with contemporary design. This innovative product caters to homeowners seeking both aesthetic appeal and functional warmth, making it suitable for a variety of living spaces.

One of the standout features of the AT-GRAND-D is its expansive viewing area, providing an unobstructed view of the flames. The large glass front enhances the ambiance of any room while maximizing the visual impact of the fire. The fireplace is designed to fit seamlessly into modern and traditional decor, thanks to its diverse finishing options and customizable installation features.

The AT-GRAND-D incorporates advanced technology to enhance efficiency and comfort. One notable technology is the IntelliFire™ ignition system, which offers reliable and easy start-ups. This system ensures that the fireplace ignites quickly at the push of a button, eliminating the hassle of manual lighting. Additionally, it features an optional remote control that allows users to adjust the flame height and heat output, providing the ultimate convenience.

Safety is also a priority in the design of the AT-GRAND-D. It includes a safety screen that prevents accidental contact with the glass, ensuring peace of mind for families with children and pets. The unit is equipped with a temperature sensor, allowing it to automatically adjust the flame to maintain a comfortable environment and prevent overheating.

Another key characteristic of the Heat & Glo LifeStyle AT-GRAND-D is its impressive heat output. With a powerful BTU range, it is capable of effectively heating large areas, making it an excellent heating solution for open-concept living spaces or cozy nooks. Additionally, the fireplace is designed for energy efficiency, providing warmth while minimizing energy consumption.

The AT-GRAND-D offers customizable installation options, including the ability to use it as a built-in unit or as a standalone model with a sleek surround. This adaptability allows homeowners to create a unique focal point in their home that suits their specific needs and style preferences.

In summary, the Heat & Glo LifeStyle AT-GRAND-D gas fireplace is a top-tier option for those looking to enhance their living space with warmth and elegance. Its combination of cutting-edge technology, safety features, and stylish design makes it an excellent choice for any modern home.
Top Page Image Contents