Desa AND VM42 GAS Line HOOK-UP, Installing 9-Volt Battery in Hand-Held Remote Control Unit

Page 12

12

INSTALLATION

Optional Wireless Hand-Held Remote Control Installation (Cont.) Gas Line Hook-Up

INSTALLATION

Continued

4.Connect wires to control circuit. Connect white wire to termi- nal marked TH/TP on control valve. Connect red wire to male blade connector provided at open end of safety circuit wiring (see Wiring Diagram, page 20).

5.Locate the battery clip mounted on the back of the receiver (see Figure 16).

6.Slide 9-volt battery (not included) through the clip. Note: Only use alkaline battery.

7.Attach the terminal wires to the battery (see Figure 16).

8.Replace refractory brick access panel.

 

9-Volt Battery

Battery

Receiver

Clip

 

Terminal

 

Wires

 

Figure 16 - Installing Battery in Receiver

Installing 9-Volt Battery in Hand-Held Remote Control Unit

1.Remove battery cover on back of remote control unit.

2.Attach terminal wires to the battery (not included). Place bat- tery into the battery housing. Note: Only use alkaline battery.

3.Replace battery cover onto remote control unit.

Battery

Remote

Cover

Control Unit

Terminal Wires

9-Volt Battery

Battery

Housing

Figure 17 - Installing Battery in Hand-Held Remote Control Unit

GAS LINE HOOK-UP

WARNING: Gas line hookup should be done by your gas supplier or a qualified service person.

WARNING: Before you proceed, make sure your gas supply is OFF.

A manual shutoff valve has been included in the appliance’s gas supply system. You may consider installing an extra gas shutoff valve outside the appliance’s enclosure (check with local codes) where it can be accessed more conveniently with a key through a wall as shown in Figure 18.

In conformance with local codes, route a 1/2" NPT gas line to the appliance through hole in left side of firebox or sub-floor as shown in Figure 19.

CAUTION: Do not kink flexible gas line.

Typical Exterior Wall Gas

Shutoff

Shutoff Installation

Valve

Key

 

 

Extension

Figure 18 - Manual Shutoff Valve Installation

1/2" NPT Incoming

Black Iron Gas Line

A

7"

7"

Alternate Gas Supply Through Sub-Floor

 

M36(B,H)/VM36(B,H)

M42(B,H)/VM42(B,H)

A

8 5/8" (219mm)

10 1/2" (267mm)

 

 

 

Figure 19 - Routing Incoming Gas Line

For morevisit www..com

108795-01K

Image 12
Contents For Your Safety Vent Decorative GAS FireplaceNatural GAS What to do if YOU Smell GASTable of Contents Safety InformationUnpacking Introduction Before YOU BeginM36B,H/VM36B,H M42B,H/VM42B,H Product Specifications ModelPRE-INSTALLATION Preparation Selecting LocationClearances Mantel Clearances and Wall Details M36B,H M42B,HVM36B,H VM42B,H M36B,H M42B,H VM36B,H VM42B,HInstalling Transition Pipe and Starter Collar FramingVenting Installation Typical B-Vent ConfigurationChecking for Proper Venting Min Roof PitchInstallation Wall Switch InstallationOptional Wireless HAND-HELD Remote Control Installation Installing ReceiverInstalling 9-Volt Battery in Hand-Held Remote Control Unit GAS Line HOOK-UPEmber and PAN Material Placement OvertightenLOG Placement for M36/VM36 Models Installing Logs 3LOG Placement for M42/VM42 Models Rest the lower part of log 5 on the log 4 and onInstalling Optional Glass Door Accessory Combustion AIR KIT Model AK4 OptionalAppliance Enclosure Opening Vent Damper Removing Glass DoorsFor Your Safety Read Before Lighting Operating FireplaceLighting Instructions To Turn OFF GAS To AppliancePilot Assembly Inspecting BurnersOptional HAND-HELD Remote Operation Burner Flame PatternCleaning Maintenance Technical Service Wiring DiagramService Hints Replacement PartsTroubleshooting Observed Problem Possible Cause RemedyTroubleshooting Top Gas leak. See Warning statement atIllustrated Parts Breakdown ModelsVM42B,H Parts List Under Replacement Parts on page 20 of this manualLogsets for Models Logset for M36B, H/VM36B, H ModelsLogset for M42B, H/VM42B, H Models Owners Registration Form Postage Required Accessories Warranty Information