Desa AND VM42 Operating Fireplace, For Your Safety Read Before Lighting, Lighting Instructions

Page 18

18

OPERATING FIREPLACE

For Your Safety Read Before Lighting Lighting Instructions

To Turn off Gas to Appliance

OPERATING FIREPLACE

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop- erty damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the floor because some gas

is heavier than air and will settle on the floor.

9.Push in the knob all the way and hold in. Immediately light the pilot manually. Continue to hold the control knob in for about (1) minute after the pilot is lit. Release knob and it will pop back up. Pilot should remain lit. If it goes out, re- peat steps 5 through 9.

If knob does not pop up when released, stop and im- mediately call your service technician or gas supplier.

If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier.

10.Turn gas control knob counterclockwise C-clockwiseto “ON”.

Knob can be turned to “ON” only if the control knob is popped out.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in

 

your building.

Immediately call your gas supplier from a neighbor’s

 

phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire de-

 

partment.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by

hand, don’t try to repair it, call a qualified service techni-

11.Replace front refractory brick access panel.

12.Fully close glass doors if installed.

13.Turn on all electric power to the appliance.

Gas Control Knob

ON

IN

T

L

 

O

 

I

 

P

OFF

Pilot

Adjustment

Screw

cian or gas supplier. Force or attempted repair may result

in a fire or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

NOTICE: During initial operation of new heater, burn- ing logs will give off a paper-burning smell. Orange flame will also be present. Open damper or window to vent smell. This will only last a few hours.

1.STOP! Read the safety information, above.

2.Turn wall switch to the OFF position.

3.Turn off all electric power to the appliance.

4.Fully open glass doors if installed.

5.Remove front refractory brick access panel.

6. Turn gas control knob clockwise Clockwise to the OFF posi- tion (see Figure 39).

IN OUT

Position Indicator

Figure 39 - Control Knob in the PILOT position

TO TURN OFF GAS

TO APPLIANCE

1.Turn off the wall switch.

2.Turn off all electric power to the appliance if service is to be performed.

3.Fully open glass doors if installed.

4.Remove front hearth brick and control access panel.

5. Turn gas control knob clockwise Clockwise to “OFF”. Do not force.

6.Replace front refractory brick access panel.

7.Fully close glass doors if installed.

Pilot Burner

Thermopile

 

Ignitor

 

7.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you don’t smell gas, go to the next step.

8. Turn control knob counterclockwise C-clockwiseto the PILOT position.

For more

Figure 40 - Pilot

visit www..com

108795-01K

Image 18
Contents Natural GAS For Your SafetyVent Decorative GAS Fireplace What to do if YOU Smell GASTable of Contents Safety InformationUnpacking Introduction Before YOU BeginM36B,H/VM36B,H M42B,H/VM42B,H Product Specifications ModelPRE-INSTALLATION Preparation Selecting LocationClearances VM36B,H VM42B,H Mantel Clearances and Wall DetailsM36B,H M42B,H M36B,H M42B,H VM36B,H VM42B,HInstalling Transition Pipe and Starter Collar FramingVenting Installation Typical B-Vent ConfigurationChecking for Proper Venting Min Roof PitchOptional Wireless HAND-HELD Remote Control Installation InstallationWall Switch Installation Installing ReceiverInstalling 9-Volt Battery in Hand-Held Remote Control Unit GAS Line HOOK-UPEmber and PAN Material Placement OvertightenLOG Placement for M36/VM36 Models Installing Logs 3LOG Placement for M42/VM42 Models Rest the lower part of log 5 on the log 4 and onInstalling Optional Glass Door Accessory Combustion AIR KIT Model AK4 OptionalAppliance Enclosure Opening Vent Damper Removing Glass DoorsLighting Instructions For Your Safety Read Before LightingOperating Fireplace To Turn OFF GAS To ApplianceOptional HAND-HELD Remote Operation Pilot AssemblyInspecting Burners Burner Flame PatternService Hints Cleaning Maintenance Technical ServiceWiring Diagram Replacement PartsTroubleshooting Observed Problem Possible Cause RemedyTroubleshooting Top Gas leak. See Warning statement atIllustrated Parts Breakdown ModelsVM42B,H Parts List Under Replacement Parts on page 20 of this manualLogsets for Models Logset for M36B, H/VM36B, H ModelsLogset for M42B, H/VM42B, H Models Owners Registration Form Postage Required Accessories Warranty Information