Desa LGCFTP, LGCFTN installation manual Fireplace pilot and burner must be at least 18 above floor

Page 10

INSTALLation

Continued

CAUTION: This fireplace cre- ates warm air currents. These currents move heat to wall sur- faces next to fireplace. Installing fireplace next to vinyl or cloth wall coverings or operating fireplace where impurities (such as, but not limited to, tobacco smoke, aromatic candles, clean- ing fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.

IMPORTANT: Vent-free fireplaces add moisture to the air. Although this is beneficial, installing fire- place in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, page 6.

Note: When installing fireplace directly on carpet- ing, tile or other combustible material, other than wood flooring, the fireplace shall be installed on a metal or wood panel extending the full width and depth of the fireplace.

CAUTION: If you install the fireplace in a home garage

•fireplace pilot and burner must be at least 18" above floor.

•locate fireplace where moving vehicle will not hit it.

For convenience and efficiency, install fireplace

•where there is easy access for operation, inspec- tion and service.

•in coldest part of room

An optional blower kit is available from your dealer. See Accessories, page 27. If planning to use blower, locate fireplace near an electrical outlet.

Built-In Fireplace Installation

Built-in installation of this fireplace involves installing fireplace into a framed-in enclosure. This makes the front of fireplace flush with wall. An optional brass trim kit accessory is available (see Accessories, page 27). Brass trim will extend past sides of fireplace approximately 1/2". This will cover the rough edges of the wall opening. If installing a built-in mantel above the fireplace, you must follow the clearances shown in Figure 14, page 12. Follow the instructions below to install the fireplace in this manner. Note: Your fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against any exterior surface on the rear, sides or top of your fireplace.

 

Actual

Framing

Height

26"

26 7/8"

Front Width

26 3/4"

26 7/8"

Depth

9 1/2"

10 1/2"

Bottom

3/4"

3/4"

1.Frame in rough opening. Use dimensions shown in Figure 10 for the rough opening. If installing in a corner, use dimensions shown in Figure 11 for the rough opening. The height is 26 7/8" which is the same as the wall opening above.

10 1/2"

267/8"

3/4" Off

The Floor

267/8" Minimum

Figure 10 - Rough Opening for Installing

in Wall

365/8"

257/8"

267/8" 513/4"

Figure 11 - Rough Opening for Installing

in Corner

10

www.desatech.com

119508-01A

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Lgcftp and Lgcftn Shown with Optional Cabinet Mantel/Hearth Base Accessory14,000 to 26,000 Btu/Hr with Thermostat Table of Contents Safety InformationSafety Information Product Information Local CodesProvide adequate clearances around air openings Assembly Product FeaturesUnpacking Air For Combustion Ventilation AssemblyAssembling and Installing Trim Providing Adequate VentilationConfined and Unconfined Space Determining FRESH-AIR Flow for fireplace LocationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building InstallationVentilation AIR Ventilation Air From OutdoorsCheck GAS Type Installation ItemsLocating Fireplace Built-In Fireplace Installation Fireplace pilot and burner must be at least 18 above floorCheck all gas connections for leaks. See If you have not assembled firebox, follow instructions onChecking Gas Connections, Installing blower accessory GA3450TA Mantel Clearances for Built- In InstallationOptional Mantel Installation Removing Upper Louver AssemblyInstalling Blower Assembly Can cause improper and dangerReinstall valve cover shield Connecting to GAS SupplyFor Built-In Installation Extension CordAccessories, Natura LChecking GAS Connections Connecting Equipment shutoff valve to heater controlInstallation Items Needed Checking Gas ConnectionsCorrect all leaks at once Pressure Testing Fireplace Gas ConnectionsTest Pressures Equal To or Less Than Psig 3.5 kPa Operating Fireplace For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS To Appliance Manual Lighting ProcedureOperating Fireplace Thermostat Control OperationPilot Flame Pattern Cleaning MaintenanceInspecting Burner Burner Flame PatternAir Passageways CabinetExterior Troubleshooting Observed Problem Possible Cause RemedyTroubleshooting MaintenanceSee Cleaning and Mainte Maintenance,Gas leak. See Warning See Checking Gas ConnecTechnical Service SpecificationsService Hints Replacement PartsBrass Trim KIT GA6095 AccessoriesEquipment Shutoff Valve GA5010 THERMOSTATICALLY-CONTROLLED Blower KIT GA3450TAIllustrated Parts Breakdown Models Lgcftp and LgcftnParts List Parts Centrals 119508-01A Limited Warranty Warranty InformationKeep this Warranty VENT-FREE Compact fireplace

LGCFTN, LGCFTP specifications

Desa LGCFTP and LGCFTN are innovative technology solutions designed to cater to modern communication and data management needs. These platforms are part of a broader suite of services aimed at enhancing connectivity, streamlining data flow, and enabling seamless interaction between users and systems.

One of the main features of Desa LGCFTP is its robust file transfer capabilities. It utilizes the File Transfer Protocol (FTP) to ensure that data can be moved securely and efficiently over networks. This feature is particularly crucial for businesses that handle large amounts of data, as it allows for the quick transfer of files ranging from reports to multimedia content without compromising on security.

In addition to the FTP functionalities, Desa LGCFTN incorporates advanced networking technologies that enhance connectivity among users. This platform is designed to facilitate reliable connectivity options, enabling organizations to establish networks that can support various applications, from simple database queries to complex real-time data exchanges.

Both Desa LGCFTP and LGCFTN are built with scalability in mind. This means that as user requirements grow, these systems can easily adapt to accommodate increased data loads and more extensive user bases. The technology underpinning these platforms is based on an architecture that supports distributed processing, which is essential for ensuring that performance remains high, even as demand fluctuates.

Security is a top priority for both platforms. They implement a range of protocols and encryption techniques to safeguard data during transfers and while at rest. This commitment to security helps organizations maintain compliance with industry standards and regulations, which is increasingly important in today’s data-driven environment.

Desa LGCFTP and LGCFTN also emphasize user experience. Their intuitive interfaces make it easy for users to manage files and navigate through different features. This focus on usability reduces the learning curve, ensuring that teams can quickly leverage the full capabilities of the platforms without extensive training.

In summary, Desa LGCFTP and LGCFTN represent cutting-edge solutions in the realm of file transfer and network connectivity. With their emphasis on security, scalability, and user experience, these platforms are well-equipped to meet the challenges faced by modern businesses, making them invaluable tools for efficient data management and communication.
Top Page Image Contents