Desa LGCFTP Connecting to GAS Supply, For Built-In Installation, Reinstall valve cover shield

Page 14

INSTALLation

Continued

For Built-In Installation

WARNING: A licensed elec- trician must connect the wiring harness to electrical supply following all local codes. Electri- cian must provide a clamp on the box cover to secure the wiring. Wiring should be routed through the bushing in the hole on the outer casing of heater.

Follow instructions in Removing Valve Cover Shield, page 12, then

1.Install a snap bushing found in hardware kit into one of the holes found on rear of valve cover shield. The other hole is for a strain relief clamp (not supplied) to secure incoming electrical supply.

2.Follow steps 2 through 6 in Installing Blower Assembly, page 12. Also remove black wire from middle switch terminal 2.

3.Remove black plastic strain relief and power cord from switch plate. The power cord supplied will not be used in built-in installations. Pop in the plastic snap bushing found in hardware kit into the hole left by supply cord/strain relief.

4.A licensed electrician must follow the wiring diagram to connect incoming electrical supply to fan kit wiring harness (see Figure 18).

5.Plug power cord to the outlet receptacle (not provided) as shown in Figure 19. Wind the extra cable in power cord and tie it up with the plastic wire strap (see Figure 19). Set the cable bundle between the burner bracket and outer casing, away from the burner.

6.Reinstall valve cover shield.

 

Fan Switch

 

 

 

 

 

 

 

 

(Auto/Off/On)

 

 

 

 

 

 

 

 

 

1 Auto

 

 

 

 

 

 

 

 

Off

2

 

 

 

 

 

 

 

 

 

 

 

3

Blue

 

Thermostat

 

 

 

On

 

 

 

Switch

 

 

 

 

 

 

(N.O.)

110/115

 

 

Red

 

 

 

 

Blue

V.A.C.

 

 

 

 

 

Blower

 

Black

 

 

 

 

 

 

 

 

Motor

 

 

 

 

 

 

 

Red

 

 

White

 

 

 

 

 

 

White

 

 

Green

 

 

 

 

 

 

Green

Figure 18 - Wiring Diagram For Blower

Accessory Built-In Installation

7.Test to make sure the blower is working properly.

8.Reinstall upper louver assembly and hood if previously removed, (see Figure 14, page 12). Close lower louver door.

Blower Bracket

Wire

Assembly

Harness

Screw

 

 

Switch

Power

 

Switch

 

Cord

 

Plate

Outlet

 

Receptacle

Blue

 

 

Red

 

 

Plastic Wire

 

 

Strap

 

 

Valve Cover

Box

Wire

Cover

Clamp Harness

Shield

 

Connector

 

 

(not included)

Figure 19 - Installing Blower Bracket

Assembly

Extension Cord

Use extension cord if needed. The cord must have a three-prong, grounding plug and a three-hole receptacle. Make sure cord is in good shape. It must be heavy enough to carry the current needed. An un- dersized cord will cause a drop in line voltage. This will result in loss of power and overheating. Use a No. 16 AWG cord for lengths less than 50 feet.

Connecting TO GAS SUPPLY

WARNING: This appliance requires a 45° male flare fitting 5/8"-18 UNF (Unified National FineThread)inletconnectionand the flexible gas line provided.

WARNING:Aqualifiedservice person must connect fireplace to gas supply. Follow all local codes.

14

www.desatech.com

119508-01A

Image 14
Contents 14,000 to 26,000 Btu/Hr with Thermostat Shown with Optional Cabinet Mantel/Hearth Base AccessoryLgcftp and Lgcftn Table of Contents Safety InformationSafety Information Provide adequate clearances around air openings Local CodesProduct Information Unpacking Product FeaturesAssembly Air For Combustion Ventilation AssemblyAssembling and Installing Trim Providing Adequate VentilationDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for fireplace LocationConfined and Unconfined Space Ventilation Air From Inside Building InstallationVentilation AIR Ventilation Air From OutdoorsLocating Fireplace Installation ItemsCheck GAS Type Built-In Fireplace Installation Fireplace pilot and burner must be at least 18 above floorChecking Gas Connections, If you have not assembled firebox, follow instructions onCheck all gas connections for leaks. See Installing blower accessory GA3450TA Mantel Clearances for Built- In InstallationOptional Mantel Installation Removing Upper Louver AssemblyInstalling Blower Assembly Can cause improper and dangerReinstall valve cover shield Connecting to GAS SupplyFor Built-In Installation Extension CordAccessories, Natura LChecking GAS Connections Connecting Equipment shutoff valve to heater controlInstallation Items Needed Checking Gas ConnectionsTest Pressures Equal To or Less Than Psig 3.5 kPa Pressure Testing Fireplace Gas ConnectionsCorrect all leaks at once Lighting Instructions For Your Safety Read Before LightingOperating Fireplace To Turn OFF GAS To Appliance Manual Lighting ProcedureOperating Fireplace Thermostat Control OperationPilot Flame Pattern Cleaning MaintenanceInspecting Burner Burner Flame PatternExterior CabinetAir Passageways Troubleshooting Observed Problem Possible Cause RemedyTroubleshooting MaintenanceSee Cleaning and Mainte Maintenance,Gas leak. See Warning See Checking Gas ConnecTechnical Service SpecificationsService Hints Replacement PartsBrass Trim KIT GA6095 AccessoriesEquipment Shutoff Valve GA5010 THERMOSTATICALLY-CONTROLLED Blower KIT GA3450TAIllustrated Parts Breakdown Models Lgcftp and LgcftnParts List Parts Centrals 119508-01A Limited Warranty Warranty InformationKeep this Warranty VENT-FREE Compact fireplace

LGCFTN, LGCFTP specifications

Desa LGCFTP and LGCFTN are innovative technology solutions designed to cater to modern communication and data management needs. These platforms are part of a broader suite of services aimed at enhancing connectivity, streamlining data flow, and enabling seamless interaction between users and systems.

One of the main features of Desa LGCFTP is its robust file transfer capabilities. It utilizes the File Transfer Protocol (FTP) to ensure that data can be moved securely and efficiently over networks. This feature is particularly crucial for businesses that handle large amounts of data, as it allows for the quick transfer of files ranging from reports to multimedia content without compromising on security.

In addition to the FTP functionalities, Desa LGCFTN incorporates advanced networking technologies that enhance connectivity among users. This platform is designed to facilitate reliable connectivity options, enabling organizations to establish networks that can support various applications, from simple database queries to complex real-time data exchanges.

Both Desa LGCFTP and LGCFTN are built with scalability in mind. This means that as user requirements grow, these systems can easily adapt to accommodate increased data loads and more extensive user bases. The technology underpinning these platforms is based on an architecture that supports distributed processing, which is essential for ensuring that performance remains high, even as demand fluctuates.

Security is a top priority for both platforms. They implement a range of protocols and encryption techniques to safeguard data during transfers and while at rest. This commitment to security helps organizations maintain compliance with industry standards and regulations, which is increasingly important in today’s data-driven environment.

Desa LGCFTP and LGCFTN also emphasize user experience. Their intuitive interfaces make it easy for users to manage files and navigate through different features. This focus on usability reduces the learning curve, ensuring that teams can quickly leverage the full capabilities of the platforms without extensive training.

In summary, Desa LGCFTP and LGCFTN represent cutting-edge solutions in the realm of file transfer and network connectivity. With their emphasis on security, scalability, and user experience, these platforms are well-equipped to meet the challenges faced by modern businesses, making them invaluable tools for efficient data management and communication.