Desa GS38 installation manual Maintenance

Page 26

Troubleshooting

Continued

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

ODS/pilot lights but flame

1. Control knob not fully pressed in

1.

Press in control knob fully

 

goes out when control knob is

2. Control knob not pressed in

2.

After ODS/pilot lights, keep con-

released

3.

long enough

3.

trol knob pressed in 30 seconds

 

 

Equipment shutoff valve not

Fully open equipment shutoff

 

 

4.

fully open

4.

valve

 

 

Pilot flame not touching ther-

A) Contact local natural or

 

 

 

mocouple, which allows ther-

 

propane/LP gas company

 

 

 

mocouple to cool, causing

 

B) Clean ODS/pilot (see

 

 

 

pilot flame to go out. This

 

 

 

 

problem could be caused by

 

Cleaning and Maintenance,

 

 

 

one or both of the following:

 

page 23) or replace ODS/pilot

 

 

 

A) Low gas pressure

 

assembly

 

 

 

B) Dirty or partially clogged

 

 

 

 

 

5.

ODS/pilot

5.

Hand tighten until snug, then

 

 

Thermocouple connection

 

 

6.

loose at control valve

6.

tighten 1/4 turn more

 

 

Thermocouple damaged

Replace pilot assembly

 

 

7.

Control valve damaged

7.

Replace control valve

 

 

 

 

 

 

Burner does not light after

1. Burner orifice clogged

1.

Clean burner (see Cleaning

ODS/pilot is lit

 

 

 

and Maintenance, page 23)

 

 

2.

Inlet gas pressure is too low

2.

or replace burner orifice

 

 

Contact local natural gas

 

 

3.

Thermopile leads disconnected

3.

company

 

 

Reconnect leads (see Wiring

 

 

4.

or improperly connected

4.

Diagrams, page 24)

 

 

Burners will not come on in

Replace battery in transmitter

 

 

 

remote position

 

and receiver

 

 

 

 

 

 

Delayed ignition burner

1. Manifold pressure is too low

1.

Contact local natural or pro-

 

 

2.

Burner orifice clogged

2.

pane/LP gas company

 

 

Clean burner (see Cleaning

 

 

 

 

 

and Maintenance, page 23)

 

 

 

 

 

or replace burner orifice

 

 

 

 

 

 

Burner backfiring during com-

1. Burner orifice is clogged or

1.

Clean burner (see Cleaning

bustion

 

damaged

 

and Maintenance, page 23)

 

 

2.

Damaged burner

2.

or replace burner orifice

 

 

Replace damaged burner

 

 

3.

Gas regulator defective

3.

Replace gas control

26

www.desatech.com

113195-01C

Image 26
Contents Remote Ready GAS Fireplace Insert Shown with GS38 Surround Kit G8010 Brick Liner AccessoriesVI33NRB and VI33PRB Table of Contents Safety InformationSafety Information Safety Information Unpacking Remote Control AccessoriesLocal Codes Product IdentificationProviding Adequate Ventilation Product FeaturesAir For Combustion Ventilation Determining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationConfined and Unconfined Space Ventilation Air From Inside Building InstallationVentilation AIR Ventilation Air From OutdoorsCheck GAS Type Installing Surround Kit GS38 or GS43Blower Accessory Electrical HookupRemoving Screws and Screen Material, Side Wall and Ceiling Installing HoodInstallation Clearances Installing Gas Piping to Fireplace Location Installation Items NeededNatural Connecting Fireplace Insert to GAS SupplyPropane/LP Checking GAS Connections Checking Gas ConnectionsTest Pressures Equal To or Less Than Psig 3.5 kPa Fireplace Insert Installation into masonry fireplacePressure Testing Fireplace Insert Gas Connections Connecting Fireplace Insert to Gas Supply, Assembling and attaching trimInstalling Logs Installing Log SetInstalling 9-Volt Battery Not Included Receiver Installing 9-Volt BatteriesInstalling Remote Receiver Unit Lighting Instructions For your safety Read before lightingOperating Fireplace Insert Optional Hand-Held Manual Lighting ProcedureTo Turn OFF GAS To Appliance Remote OperationSafety Features Manual ModeAuto Thermostatic Mode On/Off Series Model HC100Inspecting Burners Auto Shutoff FeatureKey Pad Lock Feature Optional Blower OperationBurner Primary AIR Holes Cleaning MaintenanceBurner Flame Pattern Main burnerWiring Diagrams LogsTroubleshooting Observed Problem Possible Cause RemedyMaintenance, See Cleaning and Mainte Gas leak. See Warning Statement aboveTechnical Service SpecificationsReplacement Parts Service HintsIllustrated Parts Breakdown Models VI33NRB and VI33PRBParts List Fireplace Insert Models VI33NRB and VI33PRB Parts List Equipment Shutoff Valve GA5010 Receiver and HAND-HELD Remote Control KIT HRC100 SeriesWALL-MOUNT ON/OFF Switch 113195-01C Limited Warranty VENT-FREE GAS Fireplace Insert Warranty InformationKeep this Warranty

GS38 specifications

Desa GS38 is an innovative product that stands at the intersection of cutting-edge technology and eco-friendly design, making it a standout choice in its category. This model is an embodiment of modern engineering and functionality, catering to the needs of both residential and commercial applications.

One of the defining features of the Desa GS38 is its energy-efficient performance. Designed to minimize energy consumption while maximizing output, the GS38 utilizes advanced technologies that optimize fuel efficiency. This not only helps in reducing utility bills but also aligns with global efforts toward sustainability, making it an environmentally responsible choice. The efficient combustion system integrated into the device ensures that emissions are kept to a minimum, further contributing to a cleaner atmosphere.

Technologically, the Desa GS38 is equipped with a state-of-the-art digital control system. This allows users to monitor and adjust settings with precision, leading to greater comfort and convenience. The intuitive interface makes it easy to program heating schedules, ensuring that spaces are warmed up before they are used, eliminating energy wastage. The device also features smart connectivity, allowing it to be integrated with home automation systems for remote control and operation.

Another significant characteristic of the Desa GS38 is its robust build quality. Made from high-grade materials, the unit is designed to withstand harsh conditions while maintaining operational excellence. The heat-resistant components extend the lifespan of the product, ensuring reliability even during peak usage times.

Safety is also a priority in the design of the Desa GS38. Equipped with multiple safety features such as overheat protection and automated shut-off mechanisms, users can have peace of mind knowing that the device operates safely. This makes it an ideal solution for families and businesses alike.

In summary, the Desa GS38 is a remarkable heating solution that combines energy efficiency, advanced technology, and outstanding durability. Its user-friendly interface, smart connectivity, and safety features make it a versatile choice for various applications. As we move toward a more sustainable future, the Desa GS38 marks a significant step in the direction of eco-conscious innovation in heating solutions.