Vermont Casting RHEDV42, RHEDV25, RHEDV32 installation instructions Liner Installation Fig, Exhaust

Page 8

Vermont Castings, Majestic Products RHEDV Direct Vent Insert

4.The chimney must be clean and in good working order and constructed of noncombustible materials.

5.Make sure that all chimney cleanouts fit properly so air cannot leak into the chimney.

6.Install the appliance without trim frame and make all gas fittings and electrical connections.

7.Install the decorative trim frame. Please refer to the Frame Assembly instructions.

Installer must attach red warning plate with screws supplied with the gas fire- place insert to the inside of the firebox of the fireplace into which the gas fireplace insert is installed.

Cutting any sheet metal parts of the fireplace, in which the gas fireplace insert is to be installed, is prohibited.

Flue gas exits through the vent termination rain cap

Outside combustion air enters through the lower level of the vent termination

Secure with clamp and

three screws

1)Attach flexible pipe to rain cap

2)Secure with clamp

3)Attach raincap to

vent termination using three screws

Pull flexible pipe through vent termination

If the factory-built fireplace has no gas access hole(s) provided, an access hole of 1.5 inch (37.5mm) or less may be drilled through the lower sides or bottom of the firebox in a proper workmanship like manner. This access hole must be p lugged with a noncombustible insulation after the gas supply line has been in- stalled.

WARNING

Some factory-built fireplaces have air passages on face of fireplace for zero clearance capabilities. All trim kits are designed so as to allow airflow to these passages. Under no circumstances should these passages be blocked.

Liner Installation - Fig. 9

The collar extending down from the termina- tion base is the air intake connector. Be sure the flex vent, which is connected to this collar, is also connected to the labelled air intake flue collar on the fireplace. Make sure the Flex vent is attached on the correct collar and cap for exhaust as well.

Slide the insulation provided in the termination kit over the two (2) 3" flex liners, (to be attached to the 3" Flue collar and cap of the termination). Feed one 3" flex vent from the bottom of the termination up through the 4" sleeve. Apply hi-temp sealant on the rain cap collar and slide the flex vent over the end of the rain cap collar fastening with the clamp provided. Slide the flex liner back down the 4" sleeve until 4" cap slides over the sleeve. Attach cap to the sleeve with four (4) screws supplied. Apply hi-temp sealant over the air intake

NOTE

Minimum Vent Height -

12 feet

Maximum Vent Height -

35 feet

Air Intake

Air intake collar

Exhaust

with label

 

secured with

Exhaust collar secured

clamp and three

screws

with clamp and three

 

screws

FP1280

Fig. 9 Liner installation.

collar and attach intake flex vent in the same method. Feed the two flex liners down the chimney through the damper opening. Tighten termination to the chimney using the screws provided.

In case the fireplace opening is only minimum height 21" (533mm) and access from the front is not possible, then follow the instructions below.

1.Remove flue collar plate assembly. Unbolt the top fastener plate and move it to the back first before sliding the flue collar plate out from the top of the unit. (Fig. 10)

2.Apply a bead of hi-temp sealant on the end of the collar before attaching the liner to the flue collar. Fasten it with two clamps then adjust fastener plate all the way to the back before sliding flue gas plate back onto the unit. (Fig. 11 and Fig. 12)

8

10000801

Image 8
Contents RHEDV32 RHEDV42 Table of Contents Installation & Operating Instructions Locating Your Gas Fireplace InsertInsert Applications Please Read the Following CarefullyFireplace & Trim Dimensions RHEDV25 RHEDV32 RHEDV42Gas Specifications Gas Line InstallationMantels Gas Inlet & Manifold PressuresFan Kit Fan Removal InstructionsInstallation of Trim Switch For RN/RP Gas Valves Adjustment of Levelling Bar If RequiredVenting and Installation Right Side Installation Left Side InstallationExhaust Liner Installation FigMinimum Vent Height Feet Maximum Vent Height Air Intake Ceramic Refractory Installation Left Side Center Right SideVenting Components Operating Instructions Large Lava Rock Placement Flame Adjustment RN/RP ModelsTemperature Adjustment TN/TP Models Flame CharacteristicsFirst Firing PSE PilotSIT Pilot RHEDV25/32To Turn Off Gas To Heater What to do if YOU Smell GASTroubleshooting the Gas Control System Symptom Possible Causes Corrective ActionTroubleshooting the Gas Control System Honeywell Millivolt Valve Maintenance Cleaning the Standing Pilot Control SystemBrass Cleaning Burner and Burner CompartmentRHEDV25/32/42 Series RHEDV25/32/42 Series DescriptionSpeed Control Optional Accessories Remote ControlsTrim Assembly Zero Clearance KitA2 HE25FP Trim Key DescriptionRHE25SSP HE25LP1HE25FP Replacement Parts Do not remove existing glass with frameOnly for RN/RP Valve units HE25FPHE25BTKP Replacement Parts HE25BTKPFrame Assembly A4 Riser KitsTrim Options for RHEDV32 Rhesxl TrimsFrame Mounting General Information Front ViewRHESS, RHESL, RHESSD, RHESLD, Rhesxl Trim Replacement Parts RHESS2 RHESL3 RHESSD3 RHESLD3 RHESXL4RHEBSLP, RHEBSLA, RHEBXLP, Rhebxla Trim Replacement Parts B2 Rhebsl & Rhebxl TrimsRhebsl RhebxlRhefa Rhefp Rhefa & Rhefp TrimReplacement PartsB3 Rhefa and Rhefp Trims HECBTKP, Hecbtkmb and Hesbtkp Trim Assembly Hebtkp Trim AssemblyB4 HEBTKP, HESBTKP, HECBTK, Hecbtkmb & Hebta Trims Hebtkp Hesbtkp Hecbtk HecbtkmbKT210 Hecbtk Hecbtkmb Hesbtkp Hebtkp Hebta Riser Trim Dimensions B5 Cast Trim OptionsB6 Freestanding Kits B7 Riser KitsC2 RHE42FP Trim LP trim to be used with SSP trimRHE42SSP RHE42LP1RHE42FP Replacement Parts RHE42FPHE42BTKP Trim Replacement Parts HE42BTKPProduct Covered by this Warranty If Warranty Service is NEEDED…

RHEDV25, RHEDV42, RHEDV32 specifications

Vermont Casting has long been revered in the fireplace and stove industry for its commitment to quality and craftsmanship. Among its range of high-performance products, the RHEDV32, RHEDV25, and RHEDV42 stand out as versatile, efficient, and stylish heating solutions. These models are ideal for homeowners looking to enhance their living spaces while enjoying the warmth and comfort only a wood-burning stove can provide.

The RHEDV series features a sleek design that showcases Vermont Casting's aesthetic commitment to both form and function. Each model in the series offers a variety of sizes and styles, allowing homeowners to choose the perfect fit for their space. With a wide viewing window, these stoves provide a beautiful glimpse of the flickering flames, creating an inviting ambiance in any room.

A key feature of the RHEDV series is its efficient energy use. Each model is designed with advanced combustion technology that maximizes heat output while minimizing emissions. This not only helps reduce environmental impact but also ensures that the stoves meet stringent EPA regulations. The clean-burning technology utilized in the RHEDV32, RHEDV25, and RHEDV42 means that users can enjoy the warmth of wood without the worry of excessive smoke or harmful pollutants.

Furthermore, these models impress with their impressive heating capacity. The RHEDV32 can efficiently heat spaces up to 1,800 square feet, while the RHEDV25 and RHEDV42 cater to slightly smaller and larger areas respectively. This adaptability makes them suitable for various settings, from cozy cabins to larger family homes.

The construction of the RHEDV series reflects Vermont Casting's dedication to durability. Made from high-quality cast iron, these stoves are built to last. The material not only provides excellent heat retention but also adds to the overall aesthetic appeal. Additionally, the stoves come equipped with an air wash system that helps keep the glass clean, ensuring unobstructed views of the fire.

Ease of use is another hallmark of the RHEDV series. Each model features a straightforward operating system, allowing users to easily control the airflow and heat output. This responsiveness ensures efficient burning and optimal warmth throughout the home.

In conclusion, Vermont Casting's RHEDV32, RHEDV25, and RHEDV42 models exemplify the perfect blend of efficiency, style, and ease of use. With their advanced combustion technologies, impressive heating capacities, and durable construction, they are an excellent choice for anyone looking to improve their home heating experience while adding a touch of elegance to their décor.