Vermont Casting DV580 manual Glass Information, Louvre Removal, Window Frame Assembly Removal

Page 23

DV360/580 Series Direct Vent Gas Fireplace

Operating Instructions

Glass Information

Only glass approved by CFM Corporation should be used on this fireplace.

• The use of any non-approved replace- ment glass will void all product warranties.

Care must be taken to avoid breakage of the glass.

Do not operate appliance with glass front re- moved, cracked or broken.

Replacement glass (complete with gasket) is available through your CFM Corporation dealer and should only be installed by a licensed quali- fied service person.

Louvre Removal

Window Frame

Assembly

Fireplace Front

Clamps

Glass

Panel

Glass

Panel

Pull Clamp

Hook

Push Clamp

Handle FP771a

To remove louvre assembly top, pull louvre up and then lift out. The louvre assembly bottom

2.

Fig. 47 Window frame assembly removal.

ed). After the initial cleaning process the glass should be cleaned two or three times during each operating

is hinged at the bottom edge and swings down. (Fig. 46)

1.

Louvre

season depending on the environment in the house.

Clean the glass after the first two weeks of operation.

Do not clean glass when hot.

Glass Panel

FP444

Fig. 46 Remove louvre assembly top.

Window Frame Assembly Removal

1.Turn the fireplace OFF (including the pilot).

2.If the unit has been operating, allow time for the components to cool.

3.Remove louvre assembly top.

4.Open the louvre assembly bottom.

5.Release the two clamps along lower edge of the frame by pulling down on clamp handles. (Fig. 47)

6.Tilt window frame assembly out slightly at the bot- tom, lift the frame up and away from the fireplace.

7.To replace window frame assembly reverse proce- dure.

Glass Cleaning

It is necessary to clean the glass periodically. During start-up condensation, which is normal, forms on the inside of the glass and causes lint, dust and other air- borne particles to cling to the glass surface. Also initial paint curing may deposit a slight film on the glass. It is therefore recommended the glass be cleaned two or three times with a non-ammonia household cleaner and warm water (gas fireplace glass cleaner is recommend-

Do not use abrasive cleaners.

Do not strike or slam the glass.

Installation of Optional Ceramic Panels

DV360

1.Remove glass.

2.Remove glass heat shield located at the top of the firebox toward the front.

3.Place the rear panel behind the rear log bracket.

4.Slide the right and left panels into place, The right and left panels will hold the rear panel in place when positioned properly.

5.Replace the glass heat shield.

6.Place the right and left hearth refractories and bring them together in the center and slide towards the front of the unit.

Replacement of

Ceramic Hearth Panels

1.Remove glass.

2.Set left and right panels on hearth and bring towards front of unit.

24

20010667

Image 23
Contents Direct Vent Gas Fireplace Locating Your Fireplace Installation & Operating InstructionsDV360 DV580 Fireplace Dimensions Installed as Top VentFraming Dimensions Fireplace Dimensions Installed as Rear VentHearth Clearance to CombustiblesMantels Gas Inlet and Manifold Pressures Framing And FinishingFinal Finishing Gas SpecificationsWhen purging gas line the front glass must be removed Gas Line InstallationRemote ON/OFF Switch Installation Alternate Switch LocationElectronic Gas Control Valve EB-1 Electrical BoxComplete conversion Optional Top Vent ApplicationLocation of Vent Termination General VentingGeneral Venting Information Termination Location Canadian Installations1 US Installations2Flex Vent Pipes Canadian InstallationsUSA Installations Rear Wall Vent Application How to Use the Vent GraphTwist Lock Pipes Zero clearance sleeve is only required for combustible walls Rear Wall Vent Installation Twist Lock PipeVertical Sidewall Application Rear Wall Vent Installations Flex Vent PipeAlways install horizontal venting on a level plane Vertical Sidewall Installation Twist Lock Pipe+ B = 17 Max Horizontal length requirement Vertical Sidewall Installation Flex Vent PipeVertical Through-the-Roof Application Below Grade InstallationMaximum elbow usage Vertical Through-the-Roof InstallationMin 610 mm Venting Components Replacement Ceramic Hearth Panels Window Frame Assembly RemovalGlass Cleaning Installation of Optional Ceramic PanelsLogs DV360 DV580 Installation of LogsLog Identification Chart DV360Log Overlay Top logs must be placed properly onto notches DV580Refer to Figure Large Lava Rock Burner Lava Rock PlacementFlame & Temperature Adjustment Flame CharacteristicsDV580 DV360Instructions for RF Comfort Control Valve Shut Off ProcedureTransmitter Operation Off Mode On Manual ModeChange Between F/C Temperature Units Delay Timer ModeAuto Mode Fan Override During Auto ModeAuto Path LED Count Service ActionOn Path Local Path Using a 1/2 open end wrench remove the orifices. Fig Burner Orifice Conversion DV360 Installation PrecautionsConversion Procedure Pilot Orifice ConversionInjector Orifice Size Matrix DV360/580 DV360/580 Description DV580 GACA4P0 Fuel Conversion Kits Fan Kits FK12 Fan AssemblyFK24 Fan Assembly Hard Direct Wire Hook UpDecorative Bay Windows Remote ControlsInstallation Instructions Ceramic Refractory PanelsConversion Instructions For Use in Mobile Homes Model DV360RMH9b.Units with Honeywell valve Limited Lifetime Warranty AFUE% Efficiency Ratings

DV580 specifications

The Vermont Casting DV580 is a remarkable direct vent gas fireplace that combines modern technology with the timeless craftsmanship that Vermont Castings is renowned for. This fireplace offers an exceptional combination of efficiency, style, and function, making it an ideal choice for homeowners seeking both aesthetic appeal and comfortable warmth.

One of the most significant features of the DV580 is its impressive heating capacity. With a maximum output of 33,000 BTUs, it is capable of heating spaces up to 1,800 square feet, depending on the layout of the home. This means you can enjoy consistent warmth throughout your living space, even during the coldest winter months.

Another notable characteristic is its direct vent technology, which allows for safe and efficient operation. The DV580 draws air from outside and expels combustion gases directly outdoors, minimizing indoor air pollution and ensuring optimal combustion. This design not only improves energy efficiency but also contributes to a healthier indoor environment.

The aesthetic appeal of the DV580 is enhanced by its large viewing area, which presents a beautiful flame display. The fireplace features a realistic log set that captures the look of a traditional wood-burning fire, complemented by a variety of decorative trim options. Available in both a traditional and contemporary design, the DV580 can seamlessly integrate into diverse home styles.

Vermont Castings also prioritizes user-friendliness with the DV580. An intuitive control panel allows for easy adjustments to the flame height and heat output, ensuring that homeowners can customize their experience. Additionally, an optional remote control offers added convenience, allowing users to manage the fireplace from the comfort of their seating area.

Durability is another hallmark of the DV580. Constructed from high-quality materials, it is designed to withstand the test of time. The unit is backed by a solid warranty, reflecting the manufacturer’s confidence in its reliability and performance.

In summary, the Vermont Casting DV580 is a premier gas fireplace that beautifully marries form and function. With its efficient heating capabilities, direct vent technology, stunning aesthetic options, and user-centric features, it stands out as a top choice for those looking to elevate their living space while enjoying the cozy warmth of a fireplace.