Vermont Casting 2160 manual Reloading and Reviving a Wood Fire, Remove and Store Ash Safely

Page 22

Dutchwest Sequoia

correct this situation, roll up a couple pieces of newspa- per, place them on top of the kindling and toward the back of the stove, light them and close the doors. This should heat the chimney enough to initiate a draft.

Once the draft is established, open the front door and light the rest of the fuel from the bottom. Do not light the main bed of fuel until the chimney begins drawing, and repeat the procedure as often as necessary if the initial attempt is unsuccessful.

4.After the temperature on the probe thermometer has reached 450-500°F (232-260°C) (depending on your individual wood and draft situation), close the stove damper. This will activate the combustor. To ensure continued operation of the combustor, let the tem- perature approach at least 850°F (454°C) before reducing the air settings.

5.Close the primary air control to a medium setting, or about 6:00-7:00 on the imaginary clock face referred to on Page 18. The fire volume will diminish immedi- ately, but the stove will continue to warm up. Main- tain control of the fire using the primary air and combustor air controls, and remember: reduce the setting for a smaller fire, increase the setting for a larger fire. Refer back to the air control settings chart on Page 18 for recommended settings at different burn rates.

DO NOT OVERFIRE THIS HEATER. Overfiring may cause a house fire, or can result in permanent damage to the stove and to the catalytic combustor. If an exterior part of the stove or the chimney connector glows, you are overfiring.

Reloading and Reviving a Wood Fire

Open the stove damper and wait at least fifteen sec- onds for the draft to increase. Open the door slowly and add the fuel. Split wood will fill the firebox more com- pletely and reduce the frequency of reloading.

Leave the stove damper open for a short time until the probe temperature reaches 800°F (430°C), then close it.

Frequently the temperature will drop below 800°F

(430°C) after reloading, particularly if the loading door is open a long time. Should the temperature drop below this level, stimulate the fire by increasing the primary air supply while leaving the stove damper open. Reduce the air supply and close the stove damper when the temperature has reached 800°F (430°C).

NOTE: If the charcoal bed is relatively thick and your fuel is well-seasoned, it is possible to add fresh fuel (smaller pieces first), close the door and damper, and reset the air control within five minutes.

Draft is affected by a number of variables, such as outside temperatures and quality of fuel. Adjusting your

operation in response to these variables may be helpful. To maintain good draft under adverse condi- tions, refuel as often as necessary to keep the bed of the firebox covered with a ‘robust’ layer of hot coals. Run the stove at temperatures a little above minimum recommended temperatures.

Remove and Store Ash Safely

Wearing protective stove gloves, check the ash pan before reloading the stove. If the ash level is close to the top, empty the pan. Before replacing the ash pan, clear away any ash that has spilled over the sides and back of the pan.

When burning wood, empty the ash drawer regularly, typically every one to three days. The frequency will vary depending on how hot you run your stove: the hotter the fire, the more wood you burn, and the faster ash will accumulate.

Ash may contain hot coals and must be treated with extreme care.

Coal ash will accumulate rather quickly and will require emptying the ash drawer at least once a day. Empty it before shaking and reloading to allow the newly-shaken ash to cool before the next shakedown.

ST744

Fig. 22 Wear a heavy stove glove for protection when removing ash.

Always Dispose of Ash in a Safe Manner

Ash should be removed frequently and placed outdoors in a metal container with a tight-fitting lid. The closed container of ash should be placed on a noncombustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ash is disposed of by burial in soil or otherwise locally dispersed, it should be retained in the closed container until all cinders have thoroughly cooled. Wood ash may be used as a garden fertilizer.

CAUTION: Never use a vacuum cleaner to remove ash from the stove; always remove and dispose of the ash properly.

22

2001049

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Sequoia Accessories Table of ContentsWelcome Specifications Sequoia, ModelChimney Types InstallationMasonry Chimneys Chimney Size Chimney Connector GuidelinesPrefabricated Chimneys Chimney HeightSecuring the Connector to a Masonry Chimney Assembling the Chimney ConnectorSecuring the Connector To a Prefabricated Chimney Freestanding InstallationsFireplace Installations Above the Fireplace Fireplace Installations Through the FireplaceWall Pass-Throughs Floor ProtectionFloor Protection for Fireplace Safe Ways to Reduce Clearances Fireplace InstallationsKeep the Stove a Safe Distance from Surrounding Materials Wall ShieldsFireplace and Mantel Trim Clearances Sequoia Clearance Chart Sequoia Clearance Diagrams Wall Shield Requirements for Common Sequoia Installations Sequoia with Stove and Chimney Connector Heat Shields Unpack the Parts AssemblyInstall the Fittings Attach the Legs and Heat ShieldInstall Air Duct for Outside Air Load Doors OperationSequoia Controls Air Controls Damper FunctionSuccessful Wood Burning Use the Air Control Settings That Work Best for YouBurn Only High-Quality Fuel How to Build a Wood Fire Keep it Going High-Efficiency Wood Burning With Catalytic CombustionConditioning Your Stove Starting and Maintaining a Wood FireRemove and Store Ash Safely Reloading and Reviving a Wood FireAlways Dispose of Ash in a Safe Manner Cleaning the Glass MaintenanceTest and Repair the Door Gaskets Avoid Damaging the Glass Damper AdjustmentRepair Missing Cement in Seams Replace Broken Glass ImmediatelyCare of the Catalytic Combustor When to Suspect a Combustor ProblemRemove and Inspect the Combustor Watch for Better Results Maintenance Schedule DailyCatalytic Combustor Draft Management Fuel Draft TestingSingle Venting CreosoteSequoia Woodburning Stove Sequoia Woodburning Stove Model Warranty CFM Specialty Home Products

2160 specifications

The Vermont Casting 2160 is a remarkable wood stove that epitomizes efficiency and craftsmanship, perfect for discerning homeowners seeking both functionality and elegance in their heating solutions. This model is designed to deliver substantial heat output while maintaining an environmentally friendly operation. With its robust construction and timeless aesthetic, the 2160 stands out in any setting.

A key feature of the Vermont Casting 2160 is its impressive heating capacity. It is capable of heating spaces up to 2,000 square feet, making it suitable for large homes or open-concept living areas. This high-efficiency wood stove boasts a nominal output of approximately 80,000 BTUs, ensuring consistent warmth even during the coldest months.

One of the standout technologies integrated into the Vermont Casting 2160 is its advanced air wash system, which keeps the glass door clean, providing an unobstructed view of the fire. This system enhances the visual appeal of the stove while minimizing maintenance. Additionally, the 2160 features a secondary combustion system that maximizes fuel efficiency and minimizes emissions. This technology ensures that the wood burns more completely, resulting in less smoke and particulate matter being released into the atmosphere.

The Vermont Casting 2160 is also engineered with a robust cast iron construction that ensures durability and longevity. Cast iron provides superior heat retention, allowing the stove to radiate warmth even after the fire has died down, thus improving overall efficiency. The stove's traditional design combines a classic grate and arched doors, making it visually appealing without sacrificing functionality.

Moreover, the Vermont Casting 2160 offers versatile installation options, including conventional chimney setups and direct vent systems. This flexibility allows homeowners to integrate the stove into their existing heating systems seamlessly. With an array of finishes available, including traditional black and enamel colors, the 2160 can easily complement any interior décor.

In conclusion, the Vermont Casting 2160 is a powerful and efficient wood stove that blends functionality with timeless design. Its advanced technologies ensure optimal burning efficiency and minimal environmental impact, making it an ideal choice for anyone looking to enhance their home heating experience while embracing sustainability. With its outstanding performance and aesthetic appeal, the Vermont Casting 2160 remains a reliable heating solution for years to come.
Top Page Image Contents