Vermont Casting 2160 manual Maintenance, Cleaning the Glass, Test and Repair the Door Gaskets

Page 23

Dutchwest Sequoia

Maintenance

Keep Your Stove Looking New And

Working Its Best

Care of the Cast Iron Surface

An occasional dusting with a dry rag will keep the painted cast iron of your Sequoia looking new.

If the paint needs retouching, allow the stove to cool completely. Wire-brush areas needing to be painted. Remove non-painted components such as air controls or cover them with masking tape. Touch up the stove with high temperature stove paint available from your local dealer. Apply the paint sparingly. Two light coats are better than one heavy one.

To remove stains or spills from porcelain enamel, first make sure the stove is completely cool. Use a dry rag or soft brush, and use only a kitchen appliance cleaner or polish recommended for enamel surfaces.

Cleaning the Glass

Most of the carbon deposits on the glass will burn off regularly during hot fires. If you wish to clean the glass more thoroughly, follow this procedure:

Be sure the glass is completely cool.

Use a glass cleaner especially made for this purpose.

Dry the glass completely.

Repair Air Leaks to Prevent Overheating

Self-Adjusting Door Latches

A tight seal of the doors ensures precision control over the firing rate, and prevents inadvertent overfiring. The self-adjusting design of your stove’s door latch enables you to control the tightness of the seal each time you close the door.

To achieve greater tightness, turn the handle more in a clockwise direction. Each movement of the handle draws the door closer to the stove.

Do not use excessive force when tightening the door latch. A tight seal is made when only moderate pres- sure is applied to the handle.

Test and Repair the Door Gaskets

Air leaks can be caused by low spots in the door gaskets. To locate such low spots, close each door on a slip of paper and attempt to pull the paper free. If the paper slips out without tearing, the gasket is not snug enough at that spot.

If the seal cannot be improved by adjusting the door latch, try shimming the gasket. Pack a small quantity of

cement or a smaller diameter gasket into the channel beneath the gasket to lift the main gasket and thereby improve its contact with the door frame.

If shimming does not improve the seal, replace the gasket following these steps:

1.Remove the original gasket by grasping an end and pulling firmly.

2.Wearing safety goggles, use a wire brush or the tip of a screwdriver to clean the channel of any remain- ing cement or bits of gasket. (Fig. 23)

 

ST560

Fig. 23

Remove gasket then clean channel with wire brush.

3.Apply a thin bead of stove cement in the newly- cleaned groove. (Fig. 24)

4.Lay the gasket into the groove. Wait until you are a couple inches from the end before you cut it.

 

Gasket

 

StoveCement

ST561

 

Fig. 24

Lay a bead of gasket cement then press gasket in

place.

 

5.Test the gasket by closing the door on a slip of paper as described above. Adjust the gasket in any areas where an inadequate seal is evident. Allow the cement to dry 24 hours before firing your stove.

All rope-type gasketing used in the Sequoia is made of fiberglass. The gasket size for the front, side and ash doors, as well as for the top and inner top, is 3/8” diameter. The front door glass is sealed with a 3/16” gasket, while the flue collar employs a 1/4” size. Two small pieces of 1/4” wire gaskets are used inside the Sequoia between the grate seals and the left side plate, and a special Interam® gasket wraps around the combustor to provide a seal.

2001049

23

Image 23
Contents Sequoia Welcome Table of ContentsAccessories Sequoia, Model SpecificationsMasonry Chimneys InstallationChimney Types Chimney Height Chimney Connector GuidelinesPrefabricated Chimneys Chimney SizeFreestanding Installations Assembling the Chimney ConnectorSecuring the Connector To a Prefabricated Chimney Securing the Connector to a Masonry ChimneyFireplace Installations Through the Fireplace Fireplace Installations Above the FireplaceFloor Protection Wall Pass-ThroughsFloor Protection for Fireplace Wall Shields Fireplace InstallationsKeep the Stove a Safe Distance from Surrounding Materials Safe Ways to Reduce ClearancesFireplace and Mantel Trim Clearances Sequoia Clearance Chart Sequoia Clearance Diagrams Wall Shield Requirements for Common Sequoia Installations Sequoia with Stove and Chimney Connector Heat Shields Attach the Legs and Heat Shield AssemblyInstall the Fittings Unpack the PartsInstall Air Duct for Outside Air Damper Function OperationSequoia Controls Air Controls Load DoorsBurn Only High-Quality Fuel Use the Air Control Settings That Work Best for YouSuccessful Wood Burning High-Efficiency Wood Burning With Catalytic Combustion How to Build a Wood Fire Keep it GoingStarting and Maintaining a Wood Fire Conditioning Your StoveAlways Dispose of Ash in a Safe Manner Reloading and Reviving a Wood FireRemove and Store Ash Safely Test and Repair the Door Gaskets MaintenanceCleaning the Glass Replace Broken Glass Immediately Damper AdjustmentRepair Missing Cement in Seams Avoid Damaging the GlassRemove and Inspect the Combustor When to Suspect a Combustor ProblemCare of the Catalytic Combustor Watch for Better Results Daily Maintenance ScheduleCatalytic Combustor Draft Management Creosote Draft TestingSingle Venting FuelSequoia Woodburning Stove Sequoia Woodburning Stove Model Warranty CFM Specialty Home Products

2160 specifications

The Vermont Casting 2160 is a remarkable wood stove that epitomizes efficiency and craftsmanship, perfect for discerning homeowners seeking both functionality and elegance in their heating solutions. This model is designed to deliver substantial heat output while maintaining an environmentally friendly operation. With its robust construction and timeless aesthetic, the 2160 stands out in any setting.

A key feature of the Vermont Casting 2160 is its impressive heating capacity. It is capable of heating spaces up to 2,000 square feet, making it suitable for large homes or open-concept living areas. This high-efficiency wood stove boasts a nominal output of approximately 80,000 BTUs, ensuring consistent warmth even during the coldest months.

One of the standout technologies integrated into the Vermont Casting 2160 is its advanced air wash system, which keeps the glass door clean, providing an unobstructed view of the fire. This system enhances the visual appeal of the stove while minimizing maintenance. Additionally, the 2160 features a secondary combustion system that maximizes fuel efficiency and minimizes emissions. This technology ensures that the wood burns more completely, resulting in less smoke and particulate matter being released into the atmosphere.

The Vermont Casting 2160 is also engineered with a robust cast iron construction that ensures durability and longevity. Cast iron provides superior heat retention, allowing the stove to radiate warmth even after the fire has died down, thus improving overall efficiency. The stove's traditional design combines a classic grate and arched doors, making it visually appealing without sacrificing functionality.

Moreover, the Vermont Casting 2160 offers versatile installation options, including conventional chimney setups and direct vent systems. This flexibility allows homeowners to integrate the stove into their existing heating systems seamlessly. With an array of finishes available, including traditional black and enamel colors, the 2160 can easily complement any interior décor.

In conclusion, the Vermont Casting 2160 is a powerful and efficient wood stove that blends functionality with timeless design. Its advanced technologies ensure optimal burning efficiency and minimal environmental impact, making it an ideal choice for anyone looking to enhance their home heating experience while embracing sustainability. With its outstanding performance and aesthetic appeal, the Vermont Casting 2160 remains a reliable heating solution for years to come.