Vermont Casting 2160 manual Wall Pass-Throughs, Floor Protection

Page 8

Dutchwest Sequoia

Wall Pass-Throughs

Whenever possible, design your installation so the connector does not pass through a combustible wall. If you must use a wall pass-through in your installation, check with your building inspector before you begin and construct it in accordance with local building codes. Also check with the chimney connector manu- facturer for any specific requirements.

Accessories are available for use as wall pass- throughs. If using one of these, make sure it has been tested and listed for use as a wall pass-through.

In the United States, the national Fire Protection Association (NFPA) has established guidelines for passing chimney connectors through combustible walls. Many building code inspectors follow these guidelines when approving installations.

Figure 10 shows one NFPA-recommended method. All combustible material in the wall is cut away a sufficient distance from the single-wall connector to provide the required 12” (305mm) clearance for the connector. Any material used to close up the opening must be noncom- bustible.

Chimney

Connector

1/2” (13mm)

Noncombustible

Material

ST727

Fig. 10 Wall pass-through enclosed with noncombustible materials.

Three other methods are also approved by the NFPA. These are:

Using a section of double-wall chimney with a 9” clearance to combustibles.

Placing a chimney connector pipe inside a ventilated thimble, which is then separated from combustibles by 6” of fiberglass insulating material.

Placing a chimney connector pipe inside a section of 8” diameter, solid-insulated, factory-built chimney, with 2” of air space between the chimney section and combustibles.

In Canada, the Canadian Standards Association has established different guidelines. Figure 11 shows one method, in which all combustible material in the wall is cut away to provide the required 18” (457mm) clear- ance for the connector. The resulting space must remain empty. A flush-mounted sheet metal cover may be used on one side only. If covers must be used on both sides, each cover must be mounted on noncom- bustible spacers at least 1” (25mm) clear of the wall. Your local dealer or your local building inspector can provide details of other approved methods of passing a chimney connector through a combustible wall. In Canada, this type of installation must conform to CAN/ CSA-B365, Installation Code for Solid Fuel Burning Appliances and Equipment.

NOTE: Do not vent your Sequoia into a factory-built (zero-clearance) fireplace. These appliances and their chimneys are specifically designed as a unit for use as fireplaces. It may void the listing or be hazardous to adapt them to any other use.

DO NOT CONNECT THE HEATER TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.

18” (450mm)

 

Empty Space All

Sheet Metal

Around the

Chimney

Cover

Connector

(One side

 

only)

ST728

Fig. 11 Hollow wall pass-through.

Floor Protection

A tremendous amount of heat radiates from the bottom plate of your Sequoia stove. The floor area directly under and around the stove will require protection from radiant heat as well as from stray sparks or embers that may escape the firebox.

Heat protection is provided through the use of a Dutchwest Bottom Heat Shield. Spark and ember protection must be provided by a floor protector constructed with noncombustible material as specified. Most installations will require that the bottom heat shield be attached. Only when the stove is placed on a

8

2001049

Image 8
Contents Sequoia Welcome Table of ContentsAccessories Specifications Sequoia, ModelMasonry Chimneys InstallationChimney Types Chimney Connector Guidelines Prefabricated ChimneysChimney Size Chimney HeightAssembling the Chimney Connector Securing the Connector To a Prefabricated ChimneySecuring the Connector to a Masonry Chimney Freestanding InstallationsFireplace Installations Above the Fireplace Fireplace Installations Through the FireplaceWall Pass-Throughs Floor ProtectionFloor Protection for Fireplace Fireplace Installations Keep the Stove a Safe Distance from Surrounding MaterialsSafe Ways to Reduce Clearances Wall ShieldsFireplace and Mantel Trim Clearances Sequoia Clearance Chart Sequoia Clearance Diagrams Wall Shield Requirements for Common Sequoia Installations Sequoia with Stove and Chimney Connector Heat Shields Assembly Install the FittingsUnpack the Parts Attach the Legs and Heat ShieldInstall Air Duct for Outside Air Operation Sequoia Controls Air ControlsLoad Doors Damper FunctionBurn Only High-Quality Fuel Use the Air Control Settings That Work Best for YouSuccessful Wood Burning How to Build a Wood Fire Keep it Going High-Efficiency Wood Burning With Catalytic CombustionConditioning Your Stove Starting and Maintaining a Wood FireAlways Dispose of Ash in a Safe Manner Reloading and Reviving a Wood FireRemove and Store Ash Safely Test and Repair the Door Gaskets MaintenanceCleaning the Glass Damper Adjustment Repair Missing Cement in SeamsAvoid Damaging the Glass Replace Broken Glass ImmediatelyRemove and Inspect the Combustor When to Suspect a Combustor ProblemCare of the Catalytic Combustor Watch for Better Results Maintenance Schedule DailyCatalytic Combustor Draft Management Draft Testing Single VentingFuel CreosoteSequoia Woodburning Stove Sequoia Woodburning Stove Model Warranty CFM Specialty Home Products

2160 specifications

The Vermont Casting 2160 is a remarkable wood stove that epitomizes efficiency and craftsmanship, perfect for discerning homeowners seeking both functionality and elegance in their heating solutions. This model is designed to deliver substantial heat output while maintaining an environmentally friendly operation. With its robust construction and timeless aesthetic, the 2160 stands out in any setting.

A key feature of the Vermont Casting 2160 is its impressive heating capacity. It is capable of heating spaces up to 2,000 square feet, making it suitable for large homes or open-concept living areas. This high-efficiency wood stove boasts a nominal output of approximately 80,000 BTUs, ensuring consistent warmth even during the coldest months.

One of the standout technologies integrated into the Vermont Casting 2160 is its advanced air wash system, which keeps the glass door clean, providing an unobstructed view of the fire. This system enhances the visual appeal of the stove while minimizing maintenance. Additionally, the 2160 features a secondary combustion system that maximizes fuel efficiency and minimizes emissions. This technology ensures that the wood burns more completely, resulting in less smoke and particulate matter being released into the atmosphere.

The Vermont Casting 2160 is also engineered with a robust cast iron construction that ensures durability and longevity. Cast iron provides superior heat retention, allowing the stove to radiate warmth even after the fire has died down, thus improving overall efficiency. The stove's traditional design combines a classic grate and arched doors, making it visually appealing without sacrificing functionality.

Moreover, the Vermont Casting 2160 offers versatile installation options, including conventional chimney setups and direct vent systems. This flexibility allows homeowners to integrate the stove into their existing heating systems seamlessly. With an array of finishes available, including traditional black and enamel colors, the 2160 can easily complement any interior décor.

In conclusion, the Vermont Casting 2160 is a powerful and efficient wood stove that blends functionality with timeless design. Its advanced technologies ensure optimal burning efficiency and minimal environmental impact, making it an ideal choice for anyone looking to enhance their home heating experience while embracing sustainability. With its outstanding performance and aesthetic appeal, the Vermont Casting 2160 remains a reliable heating solution for years to come.