Vermont Casting 2160 manual Watch for Better Results

Page 26

Dutchwest Sequoia

•For a visual inspection for blockage that can be performed without removing the combustor, have an assistant shine a bright flashlight beam up through the combustor from inside the stove’s firebox.

•If combustor removal is necessary for cleaning or closer inspection, lift it gently out of its chamber.

NOTE: Have a replacement Interam gasket available before removing the combustor.

•Check the combustor and the bottom of the refrac- tory chamber for a buildup of fly ash, and remove any ash by gently blowing air through the combustor. Do not brush the surface, as this could damage the element.

•Inspect the combustor, referring to the information in the “Catalytic Combustor Appendix” on Page 28 for information on what to look for. Although small hairline cracks will not affect performance, the combustor should be essentially intact. If the combustor is broken in pieces or has sections missing, it should be replaced. Call your local Dutchwest dealer for a replacement combustor, item #CB56. Consult the warranty section at the back of this manual for further information on catalytic combustor replacement.

•If the combustor is in good condition and clean, reinstall it. Be sure first to carefully wrap a new Interam® gasket (an extra was provided with your stove) around its perimeter before replacement. Insert the gasketed combustor back into position, and replace the refractory package.

•Before replacing the stove top, check the damper. If the gasket is intact, but the damper is not locking tightly, adjustment should be made. Directions for adjusting the damper are on Page 24. Also check the gasket that seals the top plate.

•Gasket should be replaced only if damaged or missing. The top plate and gasket both are sealed with a 3/8” gasket. The procedure for removing the old gasket and installing the new is the same as that described for door gaskets on Page 23.

•Replace the stove top, and secure it by tightening the two top plate bolts from inside the firebox. Be sure the top plate seats properly before tightening. Tighten the bolts gradually and alternately.

Watch for Better Results

Finish up by cleaning the chimney and chimney con- nector. Then, operate the stove in a typical manner for two weeks and observe the stove’s performance, taking particular note of the performance tests described above.

If a problem persists, contact your local dealer for further advice about your particular situation.

A Clean Chimney System is

Safer and Works Better

Learn to Recognize Creosote and Soot

When you first begin using the stove, check daily for creosote - a substance that can look like either thick tar or black, crisp flakes. Experience will show how often you need to clean to be safe. The frequency may even vary during the year. In the colder months when the hottest fires producing the least creosote are burned, you may need to clean less frequently. During the warmer months when creosote is more likely to result from cooler-burning fires, more frequent cleaning may be necessary.

At the very least, inspect the chimney and chimney connector twice monthly. Clean if necessary. Let the stove cool to determine if a buildup of creosote or soot has occurred. If a significant layer of creosote has accumulated (1/8” [3mm]), or if soot has built up, either should be removed to reduce the risk of a chimney fire. Failure to keep the chimney and connector system clean can result in a serious chimney fire.

The conditions for a chimney fire develop like this: When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire within the flue system which can damage the chimney and overheat adjacent combustible material.

To reduce the amount of creosote that may form, remember to provide adequate air for combustion and to strive for small, intense fires rather than large, smoldering ones.

Coal fires cause soot, which requires removal as well. When coal is burned, the products of combustion combine with moisture to form a soot residue which accumulates in the flue lining. When ignited, this soot makes an extremely hot fire.

You can never be too safe. Contact your local fire authority for information on what to do in the event of a chimney fire, and have a clearly defined plan on how to handle one.

Inspect Chimney Connector and Chimney

Twice Monthly and Clean as Required

Let the stove cool completely before you inspect the chimney. Then, using a strong light, sight up through the flue collar into the chimney flue. If it is not possible to inspect the flue system in this fashion, the stove must be disconnected to provide adequate viewing.

26

2001049

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Sequoia Welcome Table of ContentsAccessories Specifications Sequoia, ModelMasonry Chimneys InstallationChimney Types Chimney Size Chimney Connector GuidelinesPrefabricated Chimneys Chimney HeightSecuring the Connector to a Masonry Chimney Assembling the Chimney ConnectorSecuring the Connector To a Prefabricated Chimney Freestanding InstallationsFireplace Installations Above the Fireplace Fireplace Installations Through the FireplaceWall Pass-Throughs Floor ProtectionFloor Protection for Fireplace Safe Ways to Reduce Clearances Fireplace InstallationsKeep the Stove a Safe Distance from Surrounding Materials Wall ShieldsFireplace and Mantel Trim Clearances Sequoia Clearance Chart Sequoia Clearance Diagrams Wall Shield Requirements for Common Sequoia Installations Sequoia with Stove and Chimney Connector Heat Shields Unpack the Parts AssemblyInstall the Fittings Attach the Legs and Heat ShieldInstall Air Duct for Outside Air Load Doors OperationSequoia Controls Air Controls Damper FunctionBurn Only High-Quality Fuel Use the Air Control Settings That Work Best for YouSuccessful Wood Burning How to Build a Wood Fire Keep it Going High-Efficiency Wood Burning With Catalytic CombustionConditioning Your Stove Starting and Maintaining a Wood FireAlways Dispose of Ash in a Safe Manner Reloading and Reviving a Wood FireRemove and Store Ash Safely Test and Repair the Door Gaskets MaintenanceCleaning the Glass Avoid Damaging the Glass Damper AdjustmentRepair Missing Cement in Seams Replace Broken Glass ImmediatelyRemove and Inspect the Combustor When to Suspect a Combustor ProblemCare of the Catalytic Combustor Watch for Better Results Maintenance Schedule DailyCatalytic Combustor Draft Management Fuel Draft TestingSingle Venting CreosoteSequoia Woodburning Stove Sequoia Woodburning Stove Model Warranty CFM Specialty Home Products

2160 specifications

The Vermont Casting 2160 is a remarkable wood stove that epitomizes efficiency and craftsmanship, perfect for discerning homeowners seeking both functionality and elegance in their heating solutions. This model is designed to deliver substantial heat output while maintaining an environmentally friendly operation. With its robust construction and timeless aesthetic, the 2160 stands out in any setting.

A key feature of the Vermont Casting 2160 is its impressive heating capacity. It is capable of heating spaces up to 2,000 square feet, making it suitable for large homes or open-concept living areas. This high-efficiency wood stove boasts a nominal output of approximately 80,000 BTUs, ensuring consistent warmth even during the coldest months.

One of the standout technologies integrated into the Vermont Casting 2160 is its advanced air wash system, which keeps the glass door clean, providing an unobstructed view of the fire. This system enhances the visual appeal of the stove while minimizing maintenance. Additionally, the 2160 features a secondary combustion system that maximizes fuel efficiency and minimizes emissions. This technology ensures that the wood burns more completely, resulting in less smoke and particulate matter being released into the atmosphere.

The Vermont Casting 2160 is also engineered with a robust cast iron construction that ensures durability and longevity. Cast iron provides superior heat retention, allowing the stove to radiate warmth even after the fire has died down, thus improving overall efficiency. The stove's traditional design combines a classic grate and arched doors, making it visually appealing without sacrificing functionality.

Moreover, the Vermont Casting 2160 offers versatile installation options, including conventional chimney setups and direct vent systems. This flexibility allows homeowners to integrate the stove into their existing heating systems seamlessly. With an array of finishes available, including traditional black and enamel colors, the 2160 can easily complement any interior décor.

In conclusion, the Vermont Casting 2160 is a powerful and efficient wood stove that blends functionality with timeless design. Its advanced technologies ensure optimal burning efficiency and minimal environmental impact, making it an ideal choice for anyone looking to enhance their home heating experience while embracing sustainability. With its outstanding performance and aesthetic appeal, the Vermont Casting 2160 remains a reliable heating solution for years to come.
Top Page Image Contents