Vermont Casting 2080 Install the Chimney Connector Starter Pipe. Not supplied

Page 8

WinterWarm Small Insert

3.Install the Chimney Connector Starter Pipe. (Not supplied)

•Mark and drill two 5/16”, (8mm) holes 1⁵⁄₈” (41mm) from the lower edge of the pipe. Locate the holes on an axis that will be perpendicular to the fireplace opening when the pipe is installed. (Fig. 6)

1���" (35mm)

Fireplace

Front

FP1097

Fig. 8 Install the threaded rod inside the Starter Pipe (not a supplied item, starter pipe is available from the Chimney Con- nector manufacturer).

•Install the threaded rod (A), into the starter pipe using washers and hex nuts (B,C),on the outside of the pipe. Tighten the nuts, but do not distort the pipe opening. (Fig. 6)

•Secure the starter pipe to the chimney connector. (Fig. 7)

4.Install the Floor Protector. Make sure the floor pro- tector satisfies the requirements discussed on Page 6.

5.Install the Optional Outside Air Adapter. Follow the instructions provided with the kit.

6.Install the Optional Surround Kit. Follow the in- structions provided with the kit.

7.Slide the Firebox into Position. At least two people will be needed to move the firebox. Position the firebox so the flue collar lines up with the connector. Use the leveling screws at the front of the Insert to adjust the level. Route the power cord to the side nearest the power supply and test the fans.

8.Join the Chimney Connector to the Flue Collar.

•Assemble the draw-down hook and bar (D,E,F).

•From inside the firebox, reach up through the flue collar and engage the hook over the threaded rod inside the starter pipe. Position the steel bar behind the two tabs within the flue collar and then turn the wing nut clockwise to draw the starter pipe down. (Fig. 7)

9.Connect the Blower power cord to the power supply.

This completes installation of your WinterWarm Small Insert.

Seat the Starter

Starter Pipe

Pipe on the two

 

tabs inside the flue

 

collar

 

Draw-down Bar Assem- bly

FP1098

Fig. 7 Attach starter pipe to flue collar.

8

2000888

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Winter Warm Table of Contents IntroductionSpecifications WinterWarm Small InsertInstallation Requirements for Existing FireplacesRequirements for Existing Chimneys Chimney Height / U.S. and CanadaMinimum Fireplace Dimensions When the insert is installed in a factory-built fire- placeGeneral Considerations / U.S Sealing Requirements / U.SClearance Requirements Hearth RequirementsInstalling the WinterWarm Small Insert Optional Surround PackagesInstall the Chimney Connector Starter Pipe. Not supplied Connect the Blower power cord to the power supplyOperation Your WinterWarm Insert’s Controls and What They DoDamper Primary Air ControlUse the Air Control Settings that Work Best for You WinterWarm Small Insert Control SettingsFans Burn Only High-Quality WoodStarting and Maintaining a Wood Fire How To Build and Sustain a Wood FireHigh-Efficiency Wood Burning with Catalytic Combustion Do not over-fire this heater Reloading and Reviving a Wood FireSpecial Tactics for Cold-Climate Heating Remove and Store Ash Safely Maintenance Cleaning the GlassAdjust the Door Latch Periodically Care of the Porcelain Enamel SurfaceAdjust the Damper as Needed Removing and Replacing Door GlassReplaceable WinterWarm Small Insert Fiberglass Gaskets How to Replace GasketsReplacing the Insert’s Door Gaskets Removal and Inspection of the Combustor Refractory Package When To Suspect a Combustor ProblemCare of the Catalytic Combustor Learn To Recognize Avoid Creosote Chimney System Clean Chimney System is Safer Works BetterWatch for Better Results Flex Connection Fireplace System Maintenance ScheduleFireplace Appendix Catalytic Combustor WinterWarm Small Insert Model WinterWarm Small Insert Warranty CFM Corporation
Top Page Image Contents