Desa Tech CGF265NVA, CGF280NT Assembling and Attaching Brass Trim, Assembling Brass Trim

Page 10

INSTALLING

Continued

10

ASSEMBLING AND ATTACHING BRASS TRIM

Note: The instructions below show assembling and attaching brass trim to fireplace. Do not yet install trim if performing a built-in installation (see page 14, Built- In Fireplace Installation)

1.Remove packaging from three pieces of brass trim.

2.Locate four brass screws, two adjusting plates with set screws, and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 5.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 5).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 5).

6.While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other side.

 

Set Screws

Top Brass Trim

Side Brass Trim

Adjusting

 

 

 

Plate

 

Shim

Slot

Mitered Edge

Slot

Figure 5 - Assembling Brass Trim

8.Tighten trim hanging screws (#10 x 6.25 shoulder) into holes in cabinets. Place the assembled trim onto fireplace cabinet. Align hanging notches on trim with hanging screws on side of fireplace (see Figure 6). Push trim firmly into place, sliding hanging notches over hanging screws.

Trim Hanging

Screws

Assembled

Brass Trim

Hanging

Notches on

Trim

Figure 6 - Attaching Brass Trim to Fireplace

102664

Image 10
Contents OWNER’S Operation and Installation Manual CGF265NVA CGF280NT What to do if YOU Smell GASContents Safety Information Safety InformationProduct Identification Unpacking FeaturesLocal Codes ProductUnusually Tight Construction AIR for Combustion and VentilationProviding Adequate Ventilation Unconfined SpaceDetermining AIR Flow for Fireplace Location Determining if You Have a Confined or Unconfined SpaceVentilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Installing Check GAS TypeAssembling and Attaching Brass Trim Assembling Brass TrimConventional Fireplace Installation Minimum Wall and Ceiling Clearances see FigureLocation of Nailing Flanges Installing Cabinet Mantel BUILT-IN Fireplace Installation Rough Opening for Installing in WallMantel Clearances for Built-In Installation Mantel ShelfInstalling GAS Piping to Fireplace Location Installation Items NeededConnecting Fireplace to GAS Supply Installation Items NeededChecking GAS Connections Attaching Flexible Gas Lines TogetherPressure Testing Fireplace Gas Connections Manual Shutoff ValveInstalling Logs Installing Front LogOperating FireplaceOperating Fireplace To Turn OFF GAS to Appliance Manually-Controlled Model Variable Control Operation Pilot Flame Pattern Inspecting BurnersFront Burner Flame Pattern ODS/PILOT and Burners Trouble ShootingLogs Cleaning and Mainte TROUBLE- ShootingMaintenance, TroubleObserved Possible Remedy Problem Cause Technical ServiceHints PartsIllustrated Parts Breakdown Parts List Log Base Assembly Variable Manually Controlled ModelsCFG280NT Log Base Assembly Thermostat Controlled Models CGF265NVA CGF280NT CGF280NT CGF265NVA Accessories 102664 Warranty Information Keep this Warranty

CGF265NVA, CGF280NT specifications

The Desa Tech CGF280NT and CGF265NVA are innovative heating solutions designed for both efficiency and performance. These models combine advanced technology and user-friendly features, making them suitable for various environments, and particularly effective for residential heating needs.

The CGF280NT model is distinguished by its high-efficiency design, which allows it to deliver substantial heat output while minimizing energy consumption. One of its standout features is the Quiet Operation Technology, which significantly reduces the noise level, ensuring that your living space remains peaceful and comfortable even while the heater is in use. Additionally, it has a powerful fan that enhances heat distribution, allowing for a more consistent and comfortable temperature throughout the area.

On the other hand, the CGF265NVA model showcases a sleek, modern aesthetic that complements various interior designs. This unit is equipped with Smart Control Technology, enabling users to adjust settings from a smartphone app. This feature allows easy temperature management while improving energy efficiency. The CGF265NVA is also designed with safety in mind, integrating advanced safety features like overheat protection and an automatic shut-off system to provide peace of mind during operation.

Both models incorporate cutting-edge heat exchanger technology, which maximizes the heat output while ensuring energy savings. They boast a robust construction, with durable materials that stand up to the rigors of daily use. Furthermore, the intuitive controls on both models allow users to easily select between various heating modes, tailoring the performance to suit individual needs.

In terms of installation, both models are designed to be user-friendly, with straightforward setups that do not require extensive modifications to existing spaces. This ease of installation is complemented by their lightweight design, enabling convenient portability.

Ultimately, the Desa Tech CGF280NT and CGF265NVA are prime examples of modern heating solutions that prioritize performance, safety, and user convenience. With their advanced technologies and thoughtful design features, they represent a significant advancement in heating technology, ensuring that users enjoy a comfortable and energy-efficient environment all year round.