Empire Comfort Systems BVD34FP50, L)N-1, BVP42FP32 GAS Supply, Installing a New Main Gas Cock

Page 8

GAS SUPPLY

The gas pipeline can be brought in through the right or left side of the appliance. Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/CGA-B149 (.1 or .2) installation code.

Recommended Gas Pipe Diameter

Pipe Length

Schedule 40 Pipe

Tubing, Type L

(Feet)

Inside Diameter

Outside Diameter

 

 

 

 

 

 

Nat.

L.P.

Nat.

L.P.

 

 

 

 

 

0-10

1/2"

3/8"

1/2"

3/8"

 

12.7mm

9.5mm

12.7mm

9.5mm

 

 

 

 

 

11-40

1/2"

1/2"

5/8"

1/2"

 

12.7mm

12.7mm

15.9mm

12.7mm

 

 

 

 

 

41-100

1/2"

1/2"

3/4"

1/2"

 

12.7mm

12.7mm

19mm

12.7mm

 

 

 

 

 

101-150

3/4"

1/2"

7/8"

3/4"

 

19mm

12.7mm

22.2mm

1.9 mm

 

 

 

 

 

Note: Never use plastic pipe. Check to confirm whether your local codes allow copper tubing or galvanized.

Note: Since some municipalities have additional local codes, it is always best to consult your local authority and installation code.

The use of the following gas connectors is recommended:

ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing and Fittings.

ANS Z21.45 Assembled Flexible Appliance Connectors of Other Than All-Metal Construction

The above connectors may be used if acceptable by the authority having jurisdiction. The state of Massachusetts requires that a flexible appliance connector cannot exceed three feet in length.

 

 

Figure 6

 

Gas Supply Pressure (inches w.c.)

 

Minimum

Normal

Maximum

Natural Gas

4.5"

7.0"

14.0"

LP (Propane)

10.8"

11.0"

14.0"

 

Manifold Pressure (inches w.c.)

 

 

Normal (HI)

 

Natural Gas

 

3.5"

 

LP (Propane)

 

10.0"

 

Installing a New Main Gas Cock

Each appliance should have its own manual gas cock.

A manual main gas cock should be located in the vicinity of the unit. Where none exists, or where its size or location is not adequate, contact your local authorized installer for installation or relocation.

Compounds used on threaded joints of gas piping shall be resistant to the action of liquefied petroleum gases. The gas lines must be checked for leaks by the installer. This should be done with a soap solution watching for bubbles on all exposed connections, and if unexposed, a pressure test should be made.

Never use an exposed flame to check for leaks. Appliance must be disconnected from piping at inlet of control valve and pipe capped or plugged for pressure test. Never pressure test with appliance connected; control valve will sustain damage!

NOTE: The millivolt gas controls are equipped with a captured screw type pressure test point, therefore it is not necessary to provide a 1/8" test point up stream of the control.

Ondirectignitionvalves,hexplugsmaybereplacedwithhosefittings for pressure checks, then reinstalled before operating fireplace.

When using copper or flex connector use only approved fittings.

The appliance and it’s individual shut off valve must be disconnected from supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5kPa).

The appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5kPa).

Attention! If one of the procedures results in pressures in excess of 1/2 psig (14" w.c.) (3.5 kPa) on the fireplace gas valve, it will result in a hazardous condition.

Page 8

19400-3-0406

Image 8
Contents Installation Instructions Table of Contents Important Safety Information ApplianceSafety Information for Users of LP GAS LP-GAS Warning OdorIntroduction Specifications Fireplace DimensionsMantel Chart Figure ClearancesLocating Fireplace Combustible MaterialInstalling a New Main Gas Cock GAS SupplyChecking Manifold Pressures GAS Line HoleInstallation Vent Pipe Clearance Install the Fresh Air Kit BVA1Framing and Finishing Framing FigureCombustible Surround Installation Finishing FigureGeneral Maintenance Installing the Vent System in a ChaseVenting Vent RunsVent Configuration Offset Venting With Elbows Vent SizeNever downsize venting diameters Clearances LOG Placement 5 LOG SET Ember Material Placement on BurnerLOG Placement 3 LOG SET Operating Instructions Millivolt SystemInitial Lighting Pilot Flame FigureWall Switch, FWS-1 optional Frbc Battery Operated Remote ControlStanding Pilot Operating Instructions Millivolt ControlStanding Pilot Wiring Diagram Standing Pilot Lighting Instructions What to do if YOU Smell GASStanding Pilot Troubleshooting Frequent pilot outage problemPilot burning, no gas to burner, valve knob on Pilot and main burner extinguish while in operationStanding Pilot PROPANE/LP GAS Conversion Pilot Orifice Conversion Direct Ignition Wiring Diagram Optional Remote Control 120V Direct IgnitionFor Your Safety Read Before Lighting Direct Ignition Lighting InstructionsDirect Ignition Troubleshooting Direct Ignition PROPANE/LP GAS ConversionMaxitrol Valve Conversion Maintenance and Service Please NoteBVD34 & BVD36 Parts List Brick PANEL, PaintedBVD34 & BVD36 Parts View BVP42 Parts List Flex LINE/SHUTOFF ValveBVP42 Parts View FBB4 Optional Variable Speed Blower Installation Volt AC Junction BOX Wiring Installation Instructions Standard Millivolt Valve ModelsOptional Accessories BVA1Decorative Accessories Decorative Louver Mission Decorative Louver ArchService Notes HOW to Order Repair Parts Service Notes Service Notes

BVD34FP50, BVP42FP52, BVP42FP32, BVD34FP30, BVD36FP52 specifications

Empire Comfort Systems has carved a niche in the heating industry with its series of high-quality ventless gas fireplaces. Among their popular models are the BVD34FP50, BVD34FP30, BVD36FP52, BVP42FP52, and BVP42FP32. Each of these units combines sophisticated design with innovative technology, offering home comfort and style.

The BVD34FP50 and BVD34FP30 are known for their sleek appearance and efficient performance. These models feature a minimalist design that allows them to blend seamlessly into any room decor. The BVD34FP50 is equipped with a powerful 50,000 BTU output, making it ideal for larger areas. Conversely, the BVD34FP30, with its 30,000 BTU output, offers an energy-efficient heating solution for smaller spaces. Both models utilize Empire's advanced vent-free technology, which allows for easy installation without the need for traditional venting.

The BVD36FP52 stands out for its versatility in design and efficiency. With a 52,000 BTU capacity, it heats larger spaces effectively while maintaining a sleek and modern visible flame. This model also benefits from an adjustable flame feature, allowing users to customize the intensity to their liking. Its superior ceramic glass front provides excellent heat retention and delivers an unobstructed view of the mesmerizing flames, enhancing any living space.

Empire's BVP42FP52 and BVP42FP32 models further exemplify the brand’s commitment to innovation. The BVP42FP52 offers a robust heating capacity of 52,000 BTUs, while the BVP42FP32 delivers 32,000 BTUs, making both units adaptable for varying room sizes. These models are distinguished by their high-efficiency ceramic glass doors and programmable thermostats, allowing for precise temperature control.

All models are designed with user-friendly features such as remote control options, adjustable flame height, and safety shut-off mechanisms. Additionally, their contemporary aesthetics make them suitable for modern and traditional homes alike. Empire Comfort Systems ensures top-tier reliability and performance, making these fireplaces a worthy investment for all who seek warmth and elegance in their living spaces.