Empire Comfort Systems BVP42FP52, L)N-1, BVD34FP50 Junction BOX Wiring Installation Instructions

Page 34

JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS

STANDARD MILLIVOLT VALVE MODELS

CAUTION: ALLWIRING SHOULD BE DONE BYA QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH ALL LOCAL, CITY AND STATE BUILDING CODES. BEFORE MAKING THE ELECTRICAL CONNECTION, MAKE SURE THAT MAIN POWER SUPPLYIS DISCONNECTED.THEAPPLIANCE,WHEN INSTALLED, MUSTBE ELECTRICALLYGROUNDED IN ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL ELECTRICAL CODE ANSI/NFPA 70 (LATEST EDITION).

A factory installed junction box is located on the lower right side of the fireplace. Wiring must be fed to the junction box and attached to the receptacle that is provided. Leave approximately 6" of wire in the junction box for connection.

Attach black wire to one side of the receptacle and white wire to opposite side of receptacle. The ground wire should be attached to the green (ground) screw.

Install the receptacle into the junction box. Attach cover

 

plate.

Figure 28

120V DIRECT IGNITION VALVE MODELS

Figure 29

1.To wire Junction Box Receptacle, remove the tab on the side of the receptacle (hot side) to split receptacle. This will be required to separate blower and valve circuits.

2.Power for switched and live sides of Duplex Receptacle must come from the same power source. (One circuit breaker on main panel must switch all power off.)

3.From the wall box to the fireplace a 3-wire conductor with ground is recommended, however (2) two-wire conductors with grounds may be used in place of a 3-wire conductor with a ground if the black wires from the thermostat and blower switch are identified.

4.Two wall switches, or a wall switch and thermostat may be used to activate the two receptacle plugs independently.

Page 34

19400-3-0406

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Installation Instructions Table of Contents Important Safety Information ApplianceSafety Information for Users of LP GAS LP-GAS Warning OdorIntroduction Specifications Fireplace DimensionsLocating Fireplace Mantel Chart FigureClearances Combustible MaterialInstalling a New Main Gas Cock GAS SupplyChecking Manifold Pressures GAS Line HoleFraming and Finishing InstallationVent Pipe Clearance Install the Fresh Air Kit BVA1 Framing FigureCombustible Surround Installation Finishing FigureVenting General MaintenanceInstalling the Vent System in a Chase Vent RunsNever downsize venting diameters Clearances Vent SizeVent Configuration Offset Venting With Elbows LOG Placement 5 LOG SET Ember Material Placement on BurnerLOG Placement 3 LOG SET Initial Lighting Operating InstructionsMillivolt System Pilot Flame FigureStanding Pilot Operating Instructions Wall Switch, FWS-1 optionalFrbc Battery Operated Remote Control Millivolt ControlStanding Pilot Wiring Diagram Standing Pilot Lighting Instructions What to do if YOU Smell GASPilot burning, no gas to burner, valve knob on Standing Pilot TroubleshootingFrequent pilot outage problem Pilot and main burner extinguish while in operationStanding Pilot PROPANE/LP GAS Conversion Pilot Orifice Conversion Direct Ignition Wiring Diagram Optional Remote Control 120V Direct IgnitionFor Your Safety Read Before Lighting Direct Ignition Lighting InstructionsDirect Ignition Troubleshooting Direct Ignition PROPANE/LP GAS ConversionMaxitrol Valve Conversion Maintenance and Service Please NoteBVD34 & BVD36 Parts List Brick PANEL, PaintedBVD34 & BVD36 Parts View BVP42 Parts List Flex LINE/SHUTOFF ValveBVP42 Parts View FBB4 Optional Variable Speed Blower Installation Volt AC Junction BOX Wiring Installation Instructions Standard Millivolt Valve ModelsOptional Accessories BVA1Decorative Accessories Decorative Louver Mission Decorative Louver ArchService Notes HOW to Order Repair Parts Service Notes Service Notes

BVD34FP50, BVP42FP52, BVP42FP32, BVD34FP30, BVD36FP52 specifications

Empire Comfort Systems has carved a niche in the heating industry with its series of high-quality ventless gas fireplaces. Among their popular models are the BVD34FP50, BVD34FP30, BVD36FP52, BVP42FP52, and BVP42FP32. Each of these units combines sophisticated design with innovative technology, offering home comfort and style.

The BVD34FP50 and BVD34FP30 are known for their sleek appearance and efficient performance. These models feature a minimalist design that allows them to blend seamlessly into any room decor. The BVD34FP50 is equipped with a powerful 50,000 BTU output, making it ideal for larger areas. Conversely, the BVD34FP30, with its 30,000 BTU output, offers an energy-efficient heating solution for smaller spaces. Both models utilize Empire's advanced vent-free technology, which allows for easy installation without the need for traditional venting.

The BVD36FP52 stands out for its versatility in design and efficiency. With a 52,000 BTU capacity, it heats larger spaces effectively while maintaining a sleek and modern visible flame. This model also benefits from an adjustable flame feature, allowing users to customize the intensity to their liking. Its superior ceramic glass front provides excellent heat retention and delivers an unobstructed view of the mesmerizing flames, enhancing any living space.

Empire's BVP42FP52 and BVP42FP32 models further exemplify the brand’s commitment to innovation. The BVP42FP52 offers a robust heating capacity of 52,000 BTUs, while the BVP42FP32 delivers 32,000 BTUs, making both units adaptable for varying room sizes. These models are distinguished by their high-efficiency ceramic glass doors and programmable thermostats, allowing for precise temperature control.

All models are designed with user-friendly features such as remote control options, adjustable flame height, and safety shut-off mechanisms. Additionally, their contemporary aesthetics make them suitable for modern and traditional homes alike. Empire Comfort Systems ensures top-tier reliability and performance, making these fireplaces a worthy investment for all who seek warmth and elegance in their living spaces.
Top Page Image Contents