Enviro EG 28 owner manual Trouble Shooting, Problem Possible Cause Solution

Page 17

TROUBLE SHOOTING

Problem

Possible Cause

Solution

 

Spark will not light the pilot after

Defective piezo igniter

Check connections to igniter

repeated pressing of spark igniter

 

-If igniter connections are good but

 

 

there is no spark-replace igniter

 

Broken spark electrode

-Check for broken ceramic insulation

 

 

replace, electrode if broken

 

Miss-aligned spark electrode

-If spark is not arcing from the

 

 

electrode to pilot- adjust by loosening

 

 

screws on pilot base. Adjust and re-

 

 

tighten

 

Pilot will not remain lit

Problem with thermocouple circuit

-Check for proper connection of

 

 

thermocouple to rear of valve. If

 

 

loose, tighten lightly

 

 

-Check pilot for full flame

 

 

impingement around thermocouple.

 

 

If the pilot is to small - Check gas

 

 

pressure, adjust pilot rate screw,

 

 

check pilot head for blockage.

 

 

-Check thermocouple voltage at

 

 

valve- must be greater than 5 mV. If

 

 

low, replace thermocouple.

 

Air in gas line - (Pilot flame dies while knob

-Bleed line.

 

 

is depressed.)

-Check gas line pressure.

 

 

-Contact dealer.

Burners will not remain lit

Problem with thermopile circuit

-Check gas line pressure.

 

 

-Check for flame impingement on

 

 

thermopile, if low see “Pilot will not

 

 

stay lit”

 

 

 

-Check thermopile for a Minimum of

 

 

300 mV

when burner switched

 

 

on.

 

 

 

-Check wiring to thermostat for

 

 

breaks.

 

Flame lifting

Leak in vent pipe

-Check for leaks in vent connections

 

Improper vent configuration

-Check vent configuration with

 

Terminal may be recirculating flue gases

manual

 

 

 

-Check to see if terminal is on

 

 

correctly

 

 

 

-May need to install high wind

 

 

termination cap

 

 

-Contact dealer.

Glass fogs up

Normal conditions - after the appliance warms

up glass will clear

 

** Due to additives in gas, glass may get hazy during normal use**

 

Clean when needed.

 

 

Blue flames

Normal during start - flame will yellow as the

 

 

 

appliance heats up.

 

 

Flames are burning “dirty” or

Flame impingement

-Check log position

Sooting

 

-Increase primary air by opening

 

 

venturi shutters

 

 

See also “Burners will not stay lit”

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents What to do if YOU Smell GAS For Your SafetyFor Your Safety Safety PrecautionsCode Approvals Table of ContentsAssembly Instructions Clearances Deciding Where to Locate Your StoveDimensions Vent Terminal Clearances Simpson Duravent Parts Planning Your InstallationHorizontal Installation FIG-13 FIG-14 Vertical Installation FIG-21FIG-22 Cathedral Ceiling Installation Spring Spacers Mobile Home Venting Into Class a ChimneysInstalling the Glowing Embers Installation of Logset and EmbersLighting Instructions Operating InstructionsCleaning of Glass Maintenance and TechnicalTo Replace Door and Glass Assembly For Cleaning the Inside of the FireboxProblem Possible Cause Solution Trouble ShootingGAS Line Connection Never USE AN Open Flame for Leak Testing ElectricalOrifice SIZES, Pressure and BTU’S Natural GAS Propane GASInstalling Remote Thermostat or Wall Switch Installing or Removing the Blower Parts and AccessoriesFuel Conversion Adjusting the VenturiTo a Maximum of Seven Years WarrantyParts List Exploded EG28 FreestandingEC-059 Strip Model EG 28 Direct Vent Installation Data Sheet

EG 28 specifications

The Enviro EG 28 is an innovative environmental solution designed for efficient waste management and recycling. This versatile equipment is engineered to handle a variety of materials, making it an essential tool for waste processing facilities, recycling centers, and industrial applications. Its robust design and advanced technologies ensure optimal performance and reliability.

One of the main features of the Enviro EG 28 is its high-capacity processing capability. The system is capable of handling large volumes of waste, which increases operational efficiency and reduces the frequency of emptying and maintenance. This is particularly beneficial in high-demand environments where downtime must be minimized. The Enviro EG 28 also incorporates advanced sorting technology that allows it to differentiate between various materials, optimizing the recycling process and improving the quality of the end products.

The Enviro EG 28 utilizes cutting-edge sensors and artificial intelligence to enhance its operation. These smart technologies enable the system to automatically adjust to different types and sizes of waste materials, ensuring efficient sorting and processing. This adaptability is crucial in today’s ever-changing waste landscape, where contamination and mixed materials can pose significant challenges.

Another significant characteristic of the Enviro EG 28 is its eco-friendly design. It operates with reduced energy consumption compared to traditional waste management systems, reflecting a commitment to sustainability. The efficient use of energy not only lowers operational costs but also minimizes the environmental impact of waste processing activities.

Durability is a key attribute of the Enviro EG 28. Constructed from high-quality materials, it withstands the rigors of a demanding work environment. Its maintenance is straightforward, ensuring that organizations can keep operational disruptions to a minimum.

In summary, the Enviro EG 28 stands out in the waste management sector due to its high capacity, advanced sorting technology, smart sensors, energy efficiency, and durable construction. It represents a significant advancement toward more sustainable waste management practices, making it a valuable asset for any organization committed to environmental responsibility and operational excellence. As waste management continues to evolve, the Enviro EG 28 is poised to play a pivotal role in shaping the future of recycling and waste processing efficiency.
Top Page Image Contents