Enviro EG 28 owner manual Fuel Conversion, Adjusting the Venturi

Page 21
STEP 9. STEP 10.
STEP 11. STEP 12.
STEP 6. STEP 7. STEP 8.
STEP 1. STEP 2. STEP 3.
STEP 4. STEP 5.

ADJUSTING THE VENTURI

•Remove the ash shelf by undoing the screw at each end, pull shelf towards you.

•Remove one screw from the cover plate located

below the ash shelf. Loosen the other screw (do not remove) swing the cover plate out of the way and tighten screw down to hold it in place.

•With along screwdriver rotate spring clips to open or close the shutter to the desired setting.

•The burner flame should be a bright yellow/orange when hot. Excessive blue is to lean and dark orange with soot is too rich.

FUEL CONVERSION

“Warning” This conversion kit shall be installed by a qualified service technician in accordance

with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or CO poisoning may result. The qualified service agency is responsible for the proper installation of this kit. The installation is not proper or complete until the operation of the converted appliance is checked as specified in the owner’s conversion kit.

Please read and follow these instructions. Also please read the instruction guide lines provided by S.I.T on how to remove and install the HI-LOW regulator.

Carefully inspect all parts supplied with this conversion kit. Shut the gas off and disconnect the main gas line from the unit.

Open the door by unscrewing the ½” bolt on the right hand side of the stove. Lift door off the hinges mounted on the left-hand side. Remove the burner tray top for the appliance

Change the regulator on the front of the gas valve. (Follow the instructions provided by S.I.T)

To change the pilot orifice: First, remove the two (2) T-20 Torx screws that hold the pilot assembly to the burner tray. Lift the pilot assembly from the burner tray. Using a 10mm wrench, disconnect the pilot line from the pilot assembly and remove the pilot injector. Install the new pilot injector.

(BE CAREFUL WHEN TIGHTENING THE PILOT FITTING, YOU COULD BREAK THE CERAMIC IGNITER ELECTRODE). Re-install the pilot assembly in the reverse order of STEP 5.

Remove the burner orifice with a ½” deep socket.

Install the new orifice supplied making sure that the orifice is in the correct location. Be sure to put a bead of pipe thread sealant or approved Teflon tape on the orifice before installing into the burner assembly.

Reinstall the burner tray, log set and door.

Re connect the gas line to the unit. Do a leak check using a soap and water solution or an approved manner on the gas supply line and the pilot tubing.

Re-light the appliance to insure proper operation and proper flame appearance. Be sure to adjust the venturi setting to achieve an efficient flame in the fireplace.

MAKE SURE that the sticker provided by S.I.T is installed to signify that this valve has been converted to a different type of fuel. Also make sure that the rating plate has a conversion label to show that this unit has been converted to a different fuel type.

A VISUAL CHECK OF THE REGULATOR KNOB IS NECESSARY TO DETERMINE WHETHER OR NOT THE REGULATOR IS THE CORRECT PART. A 50% TURN DOWN REGULATOR WILL HAVE ONLY ONE CORNER ON THE KNOB.

1

50% turn down HI-LOW Regulator w 3 T-20 Torx

1 Pilot assembly mounting gasket

 

screws

NATURAL GAS

PROPANE

1

T-20 tamper proof Torx screwdriver bit

Pilot Orifice.

.51mm

.35mm

1 pilot injector

Burner Orifice.

#42 dms

#53dms

1

Main orifice

Venturi Settings

1/16” min

¼” min

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents What to do if YOU Smell GAS For Your SafetyFor Your Safety Safety PrecautionsTable of Contents Assembly InstructionsCode Approvals Deciding Where to Locate Your Stove DimensionsClearances Vent Terminal Clearances Simpson Duravent Parts Planning Your InstallationHorizontal Installation FIG-13 FIG-14 Vertical Installation FIG-21FIG-22 Cathedral Ceiling Installation Spring Spacers Mobile Home Venting Into Class a ChimneysInstalling the Glowing Embers Installation of Logset and EmbersLighting Instructions Operating InstructionsCleaning of Glass Maintenance and TechnicalTo Replace Door and Glass Assembly For Cleaning the Inside of the FireboxProblem Possible Cause Solution Trouble ShootingGAS Line Connection Never USE AN Open Flame for Leak Testing ElectricalOrifice SIZES, Pressure and BTU’S Natural GAS Propane GASInstalling Remote Thermostat or Wall Switch Installing or Removing the Blower Parts and AccessoriesFuel Conversion Adjusting the VenturiTo a Maximum of Seven Years WarrantyParts List Exploded EG28 FreestandingEC-059 Strip Model EG 28 Direct Vent Installation Data Sheet

EG 28 specifications

The Enviro EG 28 is an innovative environmental solution designed for efficient waste management and recycling. This versatile equipment is engineered to handle a variety of materials, making it an essential tool for waste processing facilities, recycling centers, and industrial applications. Its robust design and advanced technologies ensure optimal performance and reliability.

One of the main features of the Enviro EG 28 is its high-capacity processing capability. The system is capable of handling large volumes of waste, which increases operational efficiency and reduces the frequency of emptying and maintenance. This is particularly beneficial in high-demand environments where downtime must be minimized. The Enviro EG 28 also incorporates advanced sorting technology that allows it to differentiate between various materials, optimizing the recycling process and improving the quality of the end products.

The Enviro EG 28 utilizes cutting-edge sensors and artificial intelligence to enhance its operation. These smart technologies enable the system to automatically adjust to different types and sizes of waste materials, ensuring efficient sorting and processing. This adaptability is crucial in today’s ever-changing waste landscape, where contamination and mixed materials can pose significant challenges.

Another significant characteristic of the Enviro EG 28 is its eco-friendly design. It operates with reduced energy consumption compared to traditional waste management systems, reflecting a commitment to sustainability. The efficient use of energy not only lowers operational costs but also minimizes the environmental impact of waste processing activities.

Durability is a key attribute of the Enviro EG 28. Constructed from high-quality materials, it withstands the rigors of a demanding work environment. Its maintenance is straightforward, ensuring that organizations can keep operational disruptions to a minimum.

In summary, the Enviro EG 28 stands out in the waste management sector due to its high capacity, advanced sorting technology, smart sensors, energy efficiency, and durable construction. It represents a significant advancement toward more sustainable waste management practices, making it a valuable asset for any organization committed to environmental responsibility and operational excellence. As waste management continues to evolve, the Enviro EG 28 is poised to play a pivotal role in shaping the future of recycling and waste processing efficiency.
Top Page Image Contents