Enviro DV42DX owner manual To be Installed by a Qualified Service Agency only, Step

Page 11

Maintenance And Service

TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY

FUEL CONVERSION:

Warning: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or production of carbon monoxide may result causing property damage, personal injury or loss of life. The qualified service agency is responsible for the proper installation of this kit. The installation is not proper or complete until the operation of the converted appliance is checked

as specified in the manufacturer’s instructions supplied with the kit.

Please read and follow these instructions. Also, please read the instruction guidelines provided by S.I.T. on how to remove and install the HI/LO regulator.

Step 1.

Carefully inspect all parts supplied with this conversion kit.

 

Step 2.

Shut the gas supply off at the shut-off valve. (CAUTION: The gas

 

 

supply shall be shut off prior to disconnecting the electrical power,

 

Step 3.

before proceeding with the conversion.)

 

Remove the glass as shown in the MAINTENANCE AND SERVICE.

 

Step 4.

Change the regulator on the front of the gas valve (follow the

 

Step 5.

instructions provided by S.I.T.).

 

To change the pilot, simply pull the pilot hood straight up to access

 

 

the pilot injector. Using a 5/32 inch Allen key, remove the pilot

Figure 9. Ignitor assembly

 

injector.

beside the burner.

Step 6.

 

Install the new pilot injector supplied with this conversion kit. Simply screw the new injector

 

inside the pilot hood and reinstall the hood by placing the hood on the assembly, line up the

Step 7.

key way, and snap into place.

 

Remove the main burner orifice with a 1⁄2 inch deep socket.

 

Step 8.

Install the new orifice supplied. Be sure to put a bead of pipe-thread sealant or approved

Step 9.

Teflon tape on the orifice before installing into the burner assembly.

 

Reinstall the burner tray, log set, embers, and glass. When re-installing the burner, ensure that

Step 10.

the burner to pilot hood relationship is as shown on Figure 9.

 

Open the shut-off valve at the gas line to the unit.

 

Step 11.

Use a small brush to apply a warm soapy water solution to all gas connections (use a half

 

dish soap and half warm water). If a gas leak is present, bubbling will occur. Gas leaks can

 

be repaired by using an approved pipe thread sealant or approved Teflon tape. NEVER USE A

Step 12.

NAKED FLAME WHEN TESTING FOR LEAKS.

 

Re-light the fireplace to ensure proper operation and proper flame appearance.

Step 13.

MAKE SURE that the sticker provided by S.I.T. is installed, to signify that the valve has been

 

converted to a different fuel type. Also, make sure that the rating plate has a conversion label

 

to show this unit has been converted to a different fuel type.

 

A VISUAL CHECK OF THE REGULATOR KNOB IS NECESSARY TO DETERMINE WHETHER OR NOT THE REGULATOR IS THE CORRECT PART. A 50% TURN DOWN REGULATOR WILL HAVE ONLY ONE CORNER ON THE KNOB

Conversion Kit should contain the following:

 

 

(1)

50% turn down HI/LO regulator with three (3) T-20 Torx screws

 

(1)

Pilot injector

(1) Main Orifice

(NG #34 DMS; LP #51 DMS)

Conversion instructions

Pilot Orifice

(NG 0.62 mm; LP 0.35 mm)

Labels to show conversion

 

 

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents S H E R W O O D I N D U S T R I E S L T D DV42DXGeneral Safety PrecautionsTable of Contents This Enviro DV42DX Fireplace Codes And ApprovalsVented GAS Fireplace Heater DV42DX NG/LPG Installation Options SpecificationsPilot Lighting Instructions Operating InstructionsNever USE AN Open Flame for Leak Testing Component Sound & Reason To Turn GAS Fireplace OFFNo substitute materials are allowed Maintenance And ServiceCleaning Decorative Surfaces Step To be Installed by a Qualified Service Agency onlyQualified Installers only Initial InstallationCorner Installation Sheet are only approximations it is recommended Rock or Brick Finish If the faceMantel Clearances Qnty Description KIT ComponentsWire Spacer in Place Installation InstructionsManufacturer Trade Name Nominal Sizes SV4L6 Direct Vent Secure Vent Ameri Vent Description TempVenting terminals can not be recessed into a wall or siding Vent Configurations and Restrictor Settings Horizontal Vent Termination Possibility of a fireVertical Vent Termination AssembleRoof Pitch Minimum Height H Feet Meters Use of Wall Straps Ducting Electrical Requirements To Test Valve Pressures GAS Line ConnectionNever operate the fireplace with the glass door removed Secondary InstallationImportant installation notes First Stage Log Set Installation Secondary Installation Burner and FAN Removal Problem Possible Cause Solution TroubleshootingReference Description Part Number Parts List ComponentsComponentsParts Diagram Reference Options Part Number Parts List OptionsParts Diagram Options To the Distributor WarrantyTo the Dealer Installation Data Sheet

DV42DX specifications

The Enviro DV42DX is a highly efficient and eco-friendly ventilation device designed to enhance indoor air quality while minimizing energy consumption. This powerful product is tailored for residential and commercial applications, making it a versatile choice for those looking to improve air circulation.

One of the standout features of the Enviro DV42DX is its dual-speed fan system, which allows users to select the optimal airflow needed for various conditions. This not only provides flexibility but also contributes to energy efficiency, as it can operate at lower speeds during quieter periods. The adjustable fan settings ensure that users can tailor the device’s performance to meet their specific requirements.

Incorporating advanced filtration technologies, the Enviro DV42DX features an integrated HEPA filter that effectively captures airborne particles, allergens, and pollutants. This makes it an ideal choice for individuals with allergies or respiratory conditions, as it significantly reduces exposure to harmful elements in the air. Additionally, the unit is equipped with a charcoal filter that helps eliminate odors, further enhancing the indoor atmosphere.

The Enviro DV42DX is designed with user convenience in mind. It includes a programmable timer and a remote control, allowing users to operate the device from a distance and set it on a schedule that aligns with their routines. This feature not only enhances the ease of use but also encourages energy-saving habits by allowing the unit to operate only when needed.

Another characteristic of the Enviro DV42DX is its energy-efficient design, boasting a high Energy Star rating. The device not only reduces energy consumption but also saves users money on utility bills over time. Its durable construction and high-quality materials ensure longevity and reliable performance, making it a wise investment for maintaining a healthy living or working environment.

Safety is also a top priority for the Enviro DV42DX. The unit is equipped with built-in sensors that monitor air quality and automatically adjust operation to ensure optimal performance. This smart technology ensures that the device operates efficiently while maintaining safe levels of indoor air quality.

In conclusion, the Enviro DV42DX offers an impressive array of features and technologies that prioritize indoor air quality and energy efficiency. Its combination of advanced filtration, user-friendly controls, and smart technology makes it an indispensable tool for any environment aiming for cleaner and healthier air. Investing in the Enviro DV42DX is a step toward a more sustainable and comfortable indoor atmosphere.
Top Page Image Contents