Enviro EG 28 B owner manual Using AN Existing Chimney, Manufacturers General Venting Guidelines

Page 7

A. USING AN EXISTING CHIMNEY

•Measure the height of the chimney beforehand and purchase the appropriate kit. Never attempt to over stretch a flexible liner to accommodate the height of the chimney.

•Any flue damper must be removed or locked permanently in the open position.

•The chimney must be clean, in good working order and constructed out of non-combustible materials.

•Make sure that all chimney clean-outs are tightly fitting and will not permit air to leak into the chimney.

•Make all gas connections and check for leaks.

See vent manufacturer's instructions for vent system clearances to combustibles and vent terminal clearance from roof.

MANUFACTURERS GENERAL VENTING

GUIDELINES

This information is compiled by the manufacturer as a very general rule for single appliance venting of the EG 28 gas stove with 4" Type B gas vent.

Venting code and regulations may vary from area to area, please check with the local, state/provincial codes regarding the suitability of your application.

For other special venting requirements, please refer to the local, state/provincial or national codes.

For best venting performance, we recommend total vent height of 10 ft (3m) to 30 ft (9m). Total horizontal length depends on the number of elbows used. The venting

Should never slope down. 1/4" rise per 2' horizontal is recommended.

If practical, it is best to locate the appliance to permit the use of shorter horizontals and fewer elbows.

-Two 90° elbow, maximum total horizontal length of

20 ft (6m).

-Three 90° elbow, maximum total horizontal length of

13 ft (3.8m).

-Four 90° elbow, maximum total horizontal length of

6 ft (1.9m).

-Five 90° elbow, maximum total horizontal length of

0 ft (0m).

If 45° elbows are used, one 90° elbow is equivalent to two 45° elbows.

Venting rise should be a minimum of 1 ft (.31m). from the top of the unit before any horizontal run.

The bottom of the vent cap shall extend at least 2 ft. (.6m) above the highest point of the roof where it passes through and at least 2 ft (.6m) higher than any portion of the roof within a horizontal distance of 10 ft. (3m).

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents What to do if YOU Smell GAS For Your SafetyFor Your Safety Safety PrecautionsAssembly Instructions Table of ContentsCode Approvals Dimensions Deciding Where to Locate Your StoveClearances Vent Terminal Clearances Venting Flue GAS Spill SwitchManufacturers General Venting Guidelines Using AN Existing ChimneyInstalling the Logset Installing the Glowing EmbersLighting Instructions Operating InstructionsTrouble Shooting Maintenance and TechnicalProblem Possible Cause Solution Natural GAS Propane GAS Never USE AN Open Flame for Leak Testing ElectricalGAS Line Connection Orifice SIZES, Pressure and BTU’SInstalling Remote Thermostat or Wall Switch Removing or Installation of the Blower Parts and AccessoriesFuel Conversion Adjusting the VenturiTo the Dealer WarrantyTo the Distributor Parts List Exploded EG28-101 EG28-143 NG EG28-145 LPGEC-019 NG, 020 LP EC-01129/2002 Installation Data Sheet

EG 28 B specifications

The Enviro EG 28 B is an innovative solution in the realm of environmental technology, specifically designed for efficient waste management and energy resource recovery. This advanced equipment stands out in both functionality and sustainability, making it suitable for various applications in municipal and industrial settings.

One of the main features of the Enviro EG 28 B is its robust waste processing capability. The system can handle a diverse range of materials, including organic waste, plastics, and other recyclables. This flexibility allows users to maximize the efficiency of their waste management operations, promoting a circular economy. The unit is designed with a high throughput capacity, enabling it to process large volumes of waste without sacrificing performance.

The Enviro EG 28 B utilizes cutting-edge technologies to optimize every phase of waste treatment. Integrated sensors and automated controls monitor the waste processing in real-time, ensuring that the system operates at peak efficiency. This not only maximizes the recovery of valuable resources but also minimizes energy consumption. The inclusion of advanced sorting mechanisms further enhances the unit's effectiveness, allowing for the precise separation of materials for recycling and composting.

Another characteristic that sets the Enviro EG 28 B apart is its environmentally friendly approach. The equipment is engineered to significantly reduce greenhouse gas emissions throughout its operational lifespan. It employs a closed-loop system that captures and repurposes gases generated during processing, turning potential pollutants into usable energy. This aligns with global sustainability goals and positions the Enviro EG 28 B as a leader in eco-conscious waste management solutions.

Additionally, the Enviro EG 28 B is designed with user-friendliness in mind. The intuitive interface allows for easy operation and maintenance, ensuring that operators can manage the system without extensive training. Moreover, its compact design is adaptable to various locations, allowing for installation in space-constrained environments while maintaining high operational standards.

Overall, the Enviro EG 28 B exemplifies the future of waste management technology, combining efficiency, sustainability, and ease of use. Its innovative features and technologies not only help reduce environmental impact but also provide significant economic benefits to organizations seeking to optimize their resource management practices. As the need for effective waste processing continues to grow, the Enviro EG 28 B stands ready to meet these challenges head-on.
Top Page Image Contents