Enviro EG 28 B owner manual Fuel Conversion, Adjusting the Venturi

Page 15
STEP 9. STEP 10.
STEP 11. STEP 12.
STEP 6. STEP 7. STEP 8.
STEP 1. STEP 2. STEP 3.
STEP 4. STEP 5.

ADJUSTING THE VENTURI

•Remove the ash shelf by undoing the screw at each end, pull shelf towards you.

•Remove one screw from the cover plate located

below the ash shelf. Loosen the other screw (do not remove) swing the cover plate out of the way and tighten screw down to hold it in place.

•With along screwdriver rotate spring clips to open or close the shutter to the desired setting.

•The burner flame should be a bright yellow/orange when hot. Excessive blue is to lean and dark orange with soot is too rich.

FUEL CONVERSION

“Warning” This conversion kit shall be installed by a qualified service technician in accordance

with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or CO poisoning may result. The qualified service agency is responsible for the proper installation of this kit. The installation is not proper or complete until the operation of the converted appliance is checked as specified in the owner’s conversion kit.

Please read and follow these instructions. Also please read the instruction guide lines provided by S.I.T on how to remove and install the HI-LOW regulator.

Carefully inspect all parts supplied with this conversion kit. Shut the gas off and disconnect the main gas line from the unit.

Open the door by unscrewing the ½” bolt on the right hand side of the stove. Lift door off the hinges mounted on the left-hand side. Remove the burner tray top for the appliance

Change the regulator on the front of the gas valve. (Follow the instructions provided by S.I.T)

To change the pilot orifice: First, remove the two (2) T-20 Torx screws that hold the pilot assembly to the burner tray. Lift the pilot assembly from the burner tray. Using a 10mm wrench, disconnect the pilot line from the pilot assembly and remove the pilot injector. Install the new pilot injector.

(BE CAREFUL WHEN TIGHTENING THE PILOT FITTING, YOU COULD BREAK THE CERAMIC IGNITER ELECTRODE). Re-install the pilot assembly in the reverse order of STEP 5.

Remove the burner orifice with a ½” deep socket.

Install the new orifice supplied making sure that the orifice is in the correct location. Be sure to put a bead of pipe thread sealant or approved Teflon tape on the orifice before installing into the burner assembly.

Reinstall the burner tray, log set and door.

Re connect the gas line to the unit. Do a leak check using a soap and water solution or an approved manner on the gas supply line and the pilot tubing.

Re-light the appliance to insure proper operation and proper flame appearance. Be sure to adjust the venturi setting to achieve an efficient flame in the fireplace.

MAKE SURE that the sticker provided by S.I.T is installed to signify that this valve has been converted to a different type of fuel. Also make sure that the rating plate has a conversion label to show that this unit has been converted to a different fuel type.

A VISUAL CHECK OF THE REGULATOR KNOB IS NECESSARY TO DETERMINE WHETHER OR NOT THE REGULATOR IS THE CORRECT PART. A 50% TURN DOWN REGULATOR WILL HAVE ONLY ONE CORNER ON THE KNOB.

1

50% turn down HI-LOW Regulator w 3 T-20 Torx

1 Pilot assembly mounting gasket

 

screws

NATURAL GAS

PROPANE

1

T-20 tamper proof Torx screwdriver bit

Pilot Orifice.

.51mm

.35mm

1 pilot injector

Burner Orifice.

#42 dms

#53dms

1

Main orifice

Venturi Settings

1/16” min

¼” min

 

 

15

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents What to do if YOU Smell GAS For Your SafetyFor Your Safety Safety PrecautionsTable of Contents Assembly InstructionsCode Approvals Deciding Where to Locate Your Stove DimensionsClearances Vent Terminal Clearances Venting Flue GAS Spill SwitchManufacturers General Venting Guidelines Using AN Existing ChimneyInstalling the Logset Installing the Glowing EmbersLighting Instructions Operating InstructionsTrouble Shooting Maintenance and TechnicalProblem Possible Cause Solution Natural GAS Propane GAS Never USE AN Open Flame for Leak Testing ElectricalGAS Line Connection Orifice SIZES, Pressure and BTU’SInstalling Remote Thermostat or Wall Switch Removing or Installation of the Blower Parts and AccessoriesFuel Conversion Adjusting the VenturiWarranty To the DealerTo the Distributor Parts List Exploded EG28-101 EG28-143 NG EG28-145 LPGEC-019 NG, 020 LP EC-01129/2002 Installation Data Sheet

EG 28 B specifications

The Enviro EG 28 B is an innovative solution in the realm of environmental technology, specifically designed for efficient waste management and energy resource recovery. This advanced equipment stands out in both functionality and sustainability, making it suitable for various applications in municipal and industrial settings.

One of the main features of the Enviro EG 28 B is its robust waste processing capability. The system can handle a diverse range of materials, including organic waste, plastics, and other recyclables. This flexibility allows users to maximize the efficiency of their waste management operations, promoting a circular economy. The unit is designed with a high throughput capacity, enabling it to process large volumes of waste without sacrificing performance.

The Enviro EG 28 B utilizes cutting-edge technologies to optimize every phase of waste treatment. Integrated sensors and automated controls monitor the waste processing in real-time, ensuring that the system operates at peak efficiency. This not only maximizes the recovery of valuable resources but also minimizes energy consumption. The inclusion of advanced sorting mechanisms further enhances the unit's effectiveness, allowing for the precise separation of materials for recycling and composting.

Another characteristic that sets the Enviro EG 28 B apart is its environmentally friendly approach. The equipment is engineered to significantly reduce greenhouse gas emissions throughout its operational lifespan. It employs a closed-loop system that captures and repurposes gases generated during processing, turning potential pollutants into usable energy. This aligns with global sustainability goals and positions the Enviro EG 28 B as a leader in eco-conscious waste management solutions.

Additionally, the Enviro EG 28 B is designed with user-friendliness in mind. The intuitive interface allows for easy operation and maintenance, ensuring that operators can manage the system without extensive training. Moreover, its compact design is adaptable to various locations, allowing for installation in space-constrained environments while maintaining high operational standards.

Overall, the Enviro EG 28 B exemplifies the future of waste management technology, combining efficiency, sustainability, and ease of use. Its innovative features and technologies not only help reduce environmental impact but also provide significant economic benefits to organizations seeking to optimize their resource management practices. As the need for effective waste processing continues to grow, the Enviro EG 28 B stands ready to meet these challenges head-on.
Top Page Image Contents