Regency FG37-LPG Horizontal Installations, Optional Components, Snorkel Terminations, Diagram

Page 10
Diagram 1

INSTALLATION

RESIDENTIAL AND MANUFACTURED HOMES/

MOBILE HOMES INSTALLATIONS

You will require the following components with your new Regency Rear Flued Room Sealed Freestanding Gas Stove. Please review your product to make sure you have everything you need. In the event that you are missing any part, contact your dealer.

Note: These are the minimum pieces required.

Other parts may be required for your particular installation.

Minimum components for a Horizontal Installation:

946-110 Horizontal Termination Kit which includes:

1946-201 6-5/8" dia. x 18" (168mm dia. x 457mm) Black Pipe

1946-207 4" dia. x 18" (102mm dia. x 457mm) Aluminum Flue

1946-584 Astro Riser Vent Terminal

1946-202 Wall Penetration Heat Shield for Heat Sensitive walls

 

 

(Wall Thimble) (2 pcs)

1

640-545

Decorative Wall Trim (Black)

1

948-128

Tube Mill-Pac

 

 

Screws

Optional Components:

 

946-204

45o Elbow - 6-5/8" (168mm) Black pipe

 

and 4" (102mm) Aluminum Flue

946-205

Vinyl Siding Shield for Riser Vent

 

Terminal

 

946-208/P

Flue Guard

 

940

Square Wall Thimble Cover*

942Wall Penetration Heat Shield*

* Simpson Dura-Vent components

HORIZONTAL INSTALLATIONS

1)Set the unit in its desired location. Check to determine if wall studs are in the way when the fluing system is attached. If this is the case, you may want to adjust the location of the unit.

2)Assemble the desired combination of pipe and elbow to the appliance adapter with pipe seams oriented down. Offset the pipe seams as double seams in one place will cause the outer pipe to take an oval shape. Kit comes complete with 18" (457mm) of straight flue - 6-5/8" (168mm) dia. black outer pipe and 4" (102mm) dia. inner flue.

3)With the pipe attached to the stove, slide the stove into its correct location, and mark the wall for a 9-1/2" (241mm) (inside dimen- sions) round hole. The center of the round hole should line up with the centerline of the horizontal pipe, as shown in diagram 1. Cut and frame the 9-1/2 (241mm) round hole in the exterior wall where the flue will be terminated. If the wall being penetrated is constructed of non-combustible material, i.e. masonry block or concrete, a 7" (178mm) diameter hole is acceptable.

Note:

a)The horizontal run of flue should have a 1/4 inch (6mm) rise for every 1 foot (305mm) of run towards the termina- tion. Never allow the flue to run down- ward. This could cause high tempera- tures and may present the possibility of a fire.

b)The location of the horizontal flue termi- nation on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. For External Flue Terminal Locations, see diagram on page 7.

c)Snorkel Terminations:

For installations requiring a vertical rise on the exterior of the building, Astro Riser Vent Terminations as shown in Dia. 2 is available. Follow the same installation procedures as used for standard Horizontal Termination.

NEVER install the Astro Riser vent up- side down.

Diagram 2

*Dia 2: Local codes or regulations may require different clearances.

10

FG37 Regency Rear Flued Room Sealed Freestanding Gas Heater

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual Please Keep These Instructions For Future ReferenceTo the New Owner Table of Contents Data Plate General Safety Information InstallationSpecifications Save These InstructionsClearances to Combustibles Installation ChecklistLocating Your Regency GAS Stove Combustion and Ventilation AIRExterior Flue Termination Locations Clearance k in mmPlanning Your Fluing Installation Fluing Installation PrecautionsSafety Precautions for Installer FluingOffset to Vertical Terminations Vertical Terminations With Co-linear Flex SystemFlue Restrictor Position Optional Components Horizontal InstallationsDiagram Snorkel TerminationsBelow Grade Snorkel Installation Hint Apply sealant to female endVertical Termination with CO-LINEAR Flex System GAS ConnectionAntenna Control Box Cover Pilot Orifice Extrusion Assembly TubeBurner Orifice Jumper LocationAdjusting the Outlet Pressure Cable Electric ModulatorLOG SET Installation Aeration AdjustmentNG 10mm open LPG 10mm open Notch Cutout PinCutoutNotch Louvre Installation GAS Pipe Pressure TestingT. Valve Description Wiring Optional Remote ControlFinal Check Operating Instructions Summary Controls Pilot AdjustmentNormal Operating Sounds GAS Appliances Settle on the floor Copy of the Lighting Plate Instructions918-332a Maintenance Instructions MaintenanceGOLD-PLATED Doors LOG Replacement Latch AdjustmentGlass Replacement FAN Maintenance Rectly sealedManual Switch Reset Cables Pin Ground Molex Connector WireRemoving Valve Tray Parts List Electronic Components Parts ListFG37 Main Assembly FG37 Burner & LOG Assembly FG37 Door Assemblies FG37 Regency Rear Flued Room Sealed Freestanding Gas Heater Conditions WarrantyWarranty Lifetime Exclusions

FG37-NG, FG37-LPG specifications

The Regency FG37-LPG and FG37-NG are premium gas fireplaces that blend elegance with cutting-edge technology, making them ideal for modern homes. Designed by Regency, a leader in the fireplace industry, these models offer both aesthetic appeal and highly efficient heating capabilities.

The FG37-LPG is powered by liquid propane, while the FG37-NG utilizes natural gas, providing versatile options to meet different customer needs. Both models feature a sleek, contemporary design that complements various interior styles, making them a focal point in any living space. The large viewing area allows for an expansive display of flames, contributing to a warm, inviting atmosphere.

One of the standout features of the Regency FG37 series is its advanced heating technology. The fireplaces employ a high-efficiency burner system that maximizes heat output while minimizing gas consumption. This efficiency not only leads to lower energy bills but also reduces environmental impact, aligning with sustainability goals.

Additionally, the Regency FG37 models feature advanced flame control technology. Users can easily adjust the flame intensity, allowing for a custom heating experience that suits personal preferences and room sizes. This versatility makes them suitable for a variety of applications, from cozy family rooms to expansive open-concept spaces.

For added convenience, the fireplaces are equipped with a modern electronic ignition system, ensuring reliable and hassle-free startup. Customers appreciate the included remote control, which provides effortless operation from the comfort of their seats. As an optional upgrade, the Regency Smart Home Control system allows for integration with smart home devices, enabling users to manage their fireplace from their smartphones or tablets.

Safety is paramount in the design of the FG37-LPG and FG37-NG. Both models come with a built-in safety shutoff valve, ensuring that the gas supply is automatically cut off in the event of an emergency. The units also feature a glass door that remains cool to the touch, providing peace of mind for households with pets and children.

Overall, the Regency FG37-LPG and FG37-NG epitomize the perfect merger of style, efficiency, and safety. With their striking design, advanced technologies, and user-friendly features, these gas fireplaces are an excellent choice for anyone seeking to enhance their home with the luxury and warmth of a modern fireplace.
Top Page Image Contents