Lopi 028-S-75-2 owner manual Limited 5 Year Warranty, Year1 Coverage Parts & Labor

Page 36

36

Limited 5 Year Warranty

To register your TRAVIS INDUSTRIES, INC. 5 Year Warranty, complete the enclosed warranty card and mail it within ten (10) days of the appliance purchase date to: TRAVIS INDUSTRIES, INC., 4800 Harbour Pointe Blvd. SW, Mukilteo, WA 98275. TRAVIS INDUSTRIES, INC. warrants this appliance (appliance is defined as the equipment manufactured by Travis Industries, Inc.) to be defect-free in material and workmanship to the original purchaser from the date of purchase as follows:

Check with your dealer in advance for any costs to you when arranging a warranty call.

Mileage or service charges are not covered by this warranty. This charge can vary from store to store.

Year1 - COVERAGE: PARTS & LABOR

 

Cast Iron Parts

Accessories

Warranted against breakage, cracking, or burn through.

Blower

Enamel Finish

Warranted against peeling or fading, excluding chipping, mechanical abrasion, or crazing.

Combustion System

Firebrick, combustor - Warranted against breakage or deterioration not resulting from physical damage or over- loading of the wood stove.

Air Control Assembly

Slider Plate, Pressure Plate

Ceramic Glass

Glass (breakage from thermal shock)

Damper Bypass Assembly

Bypass plate, rod, handle

Door Handles and Latching Mechanism

Door handle, shaft, cam, hardware

Re-Installation Allowance

In cases where heater must be removed from home for repairs, a partial cost of re-installation is covered (pre-authorization required)

One-Way Freight Allowance

One-way freight allowance on pre-authorized repair done at factory is covered.

Ash Removal System

Cement and Gasketing

 

Ashpan, rollers, grate.

 

 

 

 

 

Exclusions: Paint

 

Years 2 & 3 - COVERAGE: PARTS & LABOR

 

Cast Iron Parts

Damper Bypass Assembly

 

Warranted against breakage, cracking, or burn through.

Bypass plate, rod, handle

Combustion System

Firebrick, combustor - Warranted against breakage or deterioration not resulting from physical damage or over- loading of the wood stove.

Air Control Assembly

Slider Plate, Pressure Plate

Door Handles and Latching Mechanism

Door handle, shaft, cam, hardware

Re-Installation Allowance

In cases where heater must be removed from home for repairs, a partial cost of re-installation is covered (pre-authorization required)

Ash Removal System

One-Way Freight Allowance

 

Ashpan, rollers, grate.

One-way freight allowance on pre-authorized repair

 

 

done at factory is covered.

 

 

 

 

Exclusions: Paint, Enamel Finish, Cement and Gasketing, Ceramic Glass, Accessories,

 

Years 4 & 5 - COVERAGE: PARTS & LABOR

Damper Bypass Assembly

Air Control Assembly

 

Slider Plate, Pressure Plate

Bypass plate, rod, handle

Ash Removal System

Door Handles and Latching Mechanism

 

Ashpan, rollers, grate.

Door handle, shaft, cam, hardware

Exclusions: Paint, Enamel Finish, Cement and Gasketing, Ceramic Glass, Accessories, Re-Installation Allowance, One-Way Freight Allowance, Cast Iron Parts, Combustion System

Page 1 of 2

© Travis Industries

100-01177

4060802

Image 36
Contents Leyden Wood Stove 2Introduction IntroductionImportant Information Save Your Bill of SaleTable of Contents Safety Precautions AshesTravis Industries, Inc. grants no warranty, implied or MobileFeatures & Specifications Installation Options FeaturesHeating Specifications DimensionsPlanning The Installation Preparation for InstallationStove Installation Considerations Installation Type ConsiderationsStove Placement Requirements Floor Protection RequirementsClearances Top View Straight Installation Top View Corner InstallationBypass Handle Installation Rear Vent ConfigurationChimney Connector Requirements Chimney Requirements DraftingPerformance Chimney Termination Requirements Outside Air RequirementsAlcove Installation Requirements Minimum Clearance Combustible See below AlcoveMobile Home Requirements Standard Ceiling with a Factory Built Chimney Cathedral Ceiling with a Factory Built ChimneyHearth Stove Positive Connection Hearth Stove Direct ConnectionInterior or Exterior Masonry Chimney Safety Notice Operating Your ApplianceBefore Your First Fire Opening the Doors Bypass Operation Loading Lid OperationStarting a Fire Starting a Top-Down FireAdjusting the Burn Rate Approximate Air Control SettingsAsh Removal Ashpan RemovalBlower Operation Re-Loading the StoveOvernight Burn Normal Operating SoundsWhy Dry Wood is Key Hints for BurningSelecting Wood Wood Cutting and StorageBurn Procedure Pictorial Overview Operating Your Appliance Troubleshooting Daily Maintenance while stove is in use Clean the Glass if necessaryMaintaining Your Appliance Remove Ash if necessaryMonthly Maintenance while appliance is in use Door and Glass InspectionCreosote Formation and Need for Removal Yearly Maintenance Clean the Combustion BrickCleaning the Air Duct and Blower if applicable Touch Up PaintAdjusting the Bypass Latch Adjusting the Ashpan LatchCleaning the Combustor Area Door Replacing the GlassReplacing the Door Gasket Replacing the Loading Lid GasketBrick Removal & Replacement Combustor Removal & ReplacementFirebox Parts Limited 5 Year Warranty Year1 Coverage Parts & LaborYears 2 & 3 Coverage Parts & Labor Years 4 & 5 Coverage Parts & LaborConditions & Exclusions Listing Label Listing LabelRear Blower Installation Optional EquipmentIndex

028-S-75-2 specifications

The Lopi 028-S-75-2 is an innovative and efficient heating solution, designed to provide optimal warmth and comfort in various residential settings. This advanced model stands out due to its superb energy efficiency, making it an ideal choice for homeowners seeking environmentally-friendly heating options without compromising on performance.

One of the main features of the Lopi 028-S-75-2 is its exceptional heating capacity. This unit is engineered to deliver an impressive output, ensuring that even larger spaces can be effectively heated. Its high BTU (British Thermal Unit) output means that the Lopi 028-S-75-2 can quickly warm up a room, making it a reliable option during the colder months.

The technology behind this model incorporates advanced catalytic combustion systems, which enhance efficiency by promoting the complete burning of fuel. This results in reduced emissions, making it a more eco-conscious choice. The inclusion of secondary combustion technology further maximizes heat production, ensuring that more energy is extracted from the fuel used.

Another characteristic that makes the Lopi 028-S-75-2 a standout is its build quality. Constructed from robust materials, this unit is designed to withstand the rigors of daily use while maintaining aesthetic appeal. Its sleek design suits a variety of home interiors, allowing it to blend seamlessly into any décor.

Ease of use is a significant consideration in the design of the Lopi 028-S-75-2. The unit features an intuitive control panel, ensuring straightforward operation. Users can easily adjust settings to match their specific heating needs, providing flexibility and convenience.

Safety features are also a priority with the Lopi 028-S-75-2. It is equipped with built-in safeguards to prevent overheating and ensure safe operation. This gives homeowners peace of mind, knowing that they have a reliable and secure heating source.

Overall, the Lopi 028-S-75-2 combines efficiency, advanced technology, and user-friendly features, making it an excellent choice for anyone looking to invest in a quality heating solution. Whether used in a cozy living room or a spacious family area, this model promises to deliver consistent warmth throughout the winter. Its commitment to performance and sustainability sets it apart in the competitive market of home heating systems.