Regency L900-1 Unit Assembly Prior to Installation, Finishing Template, Venting Introduction

Page 12

INSTALLATION

INSTALLATION

UNIT ASSEMBLY

PRIOR TO

INSTALLATION

The Top Facing Support, the Side Nailing Strips and the 2 Top Standoffs must be correctly positioned and attached to the top before unit is slipped into position.

SIDE NAILING STRIPS

The side nailing strips come attached to the unit. There are 2 plates on each side, one on the top and bottom that can be folded out as required.

TOP STANDOFF ASSEMBLY

The top standoffs are shipped in a flat position and must be folded into shape and attached.

1)Remove the standoffs from the fireplace top.

2) Take each standoff and bend into the correct shape. Bend up at the bend lines until the screw holes in the standoff and the pre- punched screw holes on the fireplace top line up.

3) Attach the standoff securely to the top with 2 screws per standoff (on opposite corners).

Side Nailing Strips shown folded out.

FINISHING TEMPLATE

In order to maintain a clean face; the L900-1 allows for a 1/8” in overlap of finishing material, such as rock or tile, on both the left and right hand sides of the unit (top and bottom sides do not allow for an overlap), this overlap must not be exceeded or the glass door will no longer open properly.

Non-combustible wall board is installed up to the flanges on all sides of the unit. When installing any additional facing material use the Finishing Template (included with the unit) to ensure that the finishing material does not exceed the allowable overlap.

The Finishing Template uses two magnets to attach itself to the flange on the left or right side of the unit (see diagram below). Install the facing material up to the outside edge (when facing the unit) of the finishing template. This template may be discarded after the facing material has been installed.

VENTING

INTRODUCTION

The L900-1 uses the "balanced flue" technology Co Axial system. The inner liner vents products of combustion to the outside while the outer liner draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.

Note: Thesefluepipesmustnotbeconnected to any other appliance.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.

12

Regency® L900-1 Direct Vent Gas Fireplace

Image 12
Contents Liberty L900-1 Gas Fireplace Manufactured Mobile Home Requirements Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Safety Label Copy of Safety DecalRequirements MA Code CO DetectorUnit Dimensions Installation General Safety InformationInstallation Checklist Important Message Save These InstructionsManufactured Mobile Home Additional Requirements Heatwave Duct KIT Heat Release KITFinished Floor Locating Your GAS FireplaceClearances Mantel Clearances Mantel LEG ClearancesFraming & Finishing NON-COMBUSTIBLE RequirementsUnit Assembly Prior to Installation Finishing TemplateVenting Introduction Vent Restrictor Position Exterior Vent Termination Requirements Minimum Clearance RequirementsVenting Arrangements Horizontal Termination FlexRigid Pipe Venting Systems Basic Horizontal & Vertical Terminations8 Rigid Pipe Cross Reference Chart Installation Vent Restrictor Setting Allowable Horizontal TerminationsHorizontal Venting with Two 2 90o Elbows Installation Allowable Vertical Terminations Unit Installation with Horizontal Termination Unit Installation With Vertical Termination This allows for small adjustmentsDiagram Minimum VentUnit Installation Astrocap XLPilot Adjustment GAS Line InstallationGAS Pipe Pressure Testing High ElevationAeration Adjustment Wiring DiagramConversion KIT #547-969 from NG to LP LP Conversion Kit Contains Qty DescriptionHingeDoor Latch Location GrateBurner Orifi ce Brick Panel Installation Handle with care. do not Force Into PositionTop Brick Panel Right Side L900-1 Left Side Brick PanelBack Brick Panel For L676-1 Units onlyLOG SET Installation Log kit # 547-930 contains the following pieces DescriptionVermiculite Installation 3rd Grate Post1st Grate Post Completed Log Set Installation Mesh Pull Screen Installation Left Side Rod Right Side RodInner Most Bracket Hole Outer Most Bracket HoleOptional Andiron Installation Final Installation L900-1Log G Replace Log GOperating Instructions For Your Safety Read Before Lighting Normal Operating Sounds GAS AppliancesCopy of Lighting Plate Instructions Lighting InstructionsMaintenance DC Spark BOX Battery Replacement DC Spark BOX ReplacementDC Spark Box Valve Tray Replacement Rear Log Stand HingeDoorValve Tray Check operation of flame controlParts List Main AssemblyParts List Burner & LOG Assembly Warranty Warranty Limited LifetimeInstaller Please complete the following information

L900-1 specifications

The Regency L900-1 is a remarkable innovation in the realm of radio equipment, designed for enthusiasts and professionals alike. Renowned for its exceptional performance, this model seamlessly integrates a plethora of advanced features, making it a top choice among users.

One of the most notable characteristics of the Regency L900-1 is its outstanding reception capabilities. Equipped with cutting-edge digital signal processing technology, this radio provides crystal-clear audio quality even in congested frequency environments. This technology minimizes noise and interference, ensuring a pristine listening experience. Users will appreciate the enhanced sensitivity and selectivity, allowing them to easily tune into distant stations or weak signals.

The design of the L900-1 is user-friendly, featuring an intuitive interface that simplifies operation. The well-organized control panel includes a large LCD display that provides vital information at a glance, such as frequency, volume levels, and signal strength. The device also includes clearly marked buttons and knobs that are easy to navigate, catering to both beginners and seasoned radio operators.

Another standout feature of the Regency L900-1 is its versatile tuning options. Users can choose between manual tuning, automatic scanning, or preset channels, offering flexibility based on individual preferences. The radio covers a broad frequency range, enabling access to AM, FM, and SW bands, which broadens the spectrum of stations and content available to users.

Additionally, the L900-1 incorporates modern connectivity options. It supports Bluetooth pairing, allowing users to stream audio from compatible devices seamlessly. This feature is ideal for those who wish to incorporate digital media into their listening experience, ensuring that they remain connected while enjoying their favorite radio shows.

Durability is also a key aspect of the Regency L900-1. Constructed with high-quality materials, this radio withstands the rigors of outdoor use. Whether you are camping, hiking, or simply enjoying a day at the beach, the solid build ensures longevity and reliability.

In summary, the Regency L900-1 combines advanced technology, user-friendly design, and robust features, making it an outstanding choice for radio enthusiasts. Its excellent reception, versatile tuning options, and modern connectivity features set it apart in the market. For those seeking a high-quality radio experience, the Regency L900-1 is undoubtedly a worthy investment.