Wayne 3014, 3514, 3018DLX user manual Two Button Transmitter Security Code Change and Programming

Page 22

Programming Transmitter to Power Head Unit

Note: Do not press any button on the Transmitter until instructed.

1.Press the PROGRAM Switch button located on the garage door power head unit once. The red PROGRAM STATUS light on the motor power head unit and overhead lamp will turn on and remain lit for one minute, indicating that it is ready to learn the Transmitter.

2.Press the button on the Transmitter you wish to use to operate the door. (NOTE: For the 2 button transmitter this must be the same button that was used in “Changing the Transmitter Code” )The PROGRAM STATUS light on the power head will turn on and off three times indicating a successful learn.

3.Press the same button on the Transmitter once more to confirm operation. The opener will turn on and move the door.

At this point you will be able to activate the opener.

Battery: If the LED (light) on Transmitter does not turn on when a button is pressed, repeat “changing the transmitter code”

operation. If LED fails to light replace battery. To change battery, insert a coin in the coin slot and twist coin to access battery compartment. Some transmitters use two CR2016 or equivalent batteries while others use a single MN21 or equivalent battery. Snap case together after replacing.

Step 23a: Two Button Transmitter Security Code Change and Programming

Available only for 303/372 MHz combo models.

Note: The following steps describe the process to change the Transmitter security code and to program the Transmitter.

IMPORTANT: You MUST change the Transmitter security code prior to programming the device to the power head unit.

WARNING: During programming the garage door may operate. Keep people and objects clear of the moving door to prevent door damage or possible personal injury.

Changing the Transmitter Code

1.Press and hold the button on the transmitter that you want to change (left button or right button). The GREEN LED (light) will flash once and then turn off.

2.Continue to hold the button until the GREEN LED begins to flash (approx. 10 seconds).

3.When the GREEN LED flashes, immediately release the button and then immediately press and hold the same button again. The GREEN LED will now come on steady.

4.Continue to hold the button until the GREEN LED begins to flash (approx. 5 seconds).

5.When the GREEN LED flashes, immediately release the button.

6.The code for this button has now been changed to a new randomly generated code. Do not press the button again until instructed in “Programming Transmitter to Motor Head Power Unit”.

7.You must now re-program this transmitter to the motor head unit. See “Programming Transmitter to Motor Head Unit” above.

Note: After the transmitter is programmed, see “Programming Transmitter to Power Head Unit” above. After completing “Programming Transmitter to Power Head Unit” proceed to step 24.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Owner Installation Important Installation Instructions Page Features Before StartingDoor Tests Before Starting Door Test OneTools You’ll Need Part Identification Hardware Identification Step Three Mounting Front Rail Assembly Rail AssemblyStep One Rail Assembly Step Two Trolley AlignmentStep Five Setting The Chain Latch Assembly Step Four Setting The ChainStep Six Rail Assembly Alignment Attaching Motor Power Head Unit to Rail Positioning and Installing Front Wall BracketPositioning the Motor End of Operator Attach Unit to Front Wall BracketMounting Motor End of Opener Installing Wired Wall Station if included Installing LightMounting Door Bracket Installing Deluxe Wireless Wall Station if included Install Entrapment Warning LabelInstall Wireless Infrared Safety Sensor Bracket Install Wireless Infrared Safety SensorInstall Wired Infrared Safety Sensor Wall Mounting Brackets Install Wiring for Wired Infrared Safety Sensor Connecting Wired Infrared Safety Sensor to OpenerMount Wired Infrared Safety Sensors Connecting Electrical PowerWireless Wall Station Security Code Change and Programming Changing Wireless Wall Station CodeAlignment of the Wireless Infrared Safety Sensors Alignment of the Wired Infrared Safety Sensors Changing the Transmitter CodeProgramming Transmitter to Power Head Unit Two Button Transmitter Security Code Change and ProgrammingConnecting Cushion Arm to Trolley Setting Trolley Close PositionConnecting Door Arm to Door IMPORTANT! Test Contact Obstruction Sensing FeatureSetting Door Opening Travel Infrared Safety Sensor Obstruction TestProgramming Wireless Keyless Entry If Included Installing Wireless Keyless Entry If IncludedAdjustments Adjustment # 1 Opening and Closing ForceAdjustment # 2 Contact Obstruction Sensing Closing Direction Adjustment # 3 Positive Mechanical Door LockImportant Safety Instructions HOW to Operate the Wireless Keyless Entry if Included Operation of Your OpenerHOW to Operate the Wireless Wall Station If Included Opener Power Head ControlsPage Twice a Year Once a MonthOnce a Year Trouble Shooting Section Parts Breakdown Rail Assembly All Models Description Per Unit # Per Unit Classicdrive Accessories Cut Template to Aid in Keyless Entry Installation See Step Pre-drill a 5/64 pilot Hole 3/4 deepLimited Lifetime Warranty Questions?

3514, 3014, 3018, 3018DLX specifications

Wayne 3014, 3018, 3018DLX, and 3514 are a series of innovative fuel dispensers designed to cater to the evolving needs of the retail fueling industry. These models embody advanced engineering, reliability, and efficiency, making them ideal solutions for gas station operators looking to enhance their service offerings.

The Wayne 3014 series is characterized by its compact design, making it a perfect fit for locations with space constraints. It features a user-friendly interface, which allows for easier interaction for both attendants and customers. The sleek and modern look of the 3014 gives stations a contemporary feel while maintaining durability against the elements.

The 3018 model builds on the robust foundation of the 3014 but adds additional features for increased throughput. With capabilities to handle multiple products, the 3018 allows for various fuel types to be dispensed efficiently, catering to the diverse needs of customers. The model is equipped with advanced metering technologies, ensuring accurate measurement and reducing loss through evaporation or spillage.

For those seeking a more premium option, the 3018DLX stands out with its enhanced features and aesthetics. It offers an integrated payment system, supporting both card and mobile payments, which vastly improves transaction speed and customer satisfaction. The dispenser is also designed with a customizable interface that allows operators to promote special offers or loyalty programs directly on the screen.

The Wayne 3514 takes technology a notch higher, incorporating robust software support that enables real-time data analytics. This feature allows station owners to monitor sales trends and inventory levels efficiently, leading to optimized operations and better decision-making. The 3514 also supports future upgrades, ensuring that the infrastructure can adapt as technology evolves.

All these models prioritize safety and regulatory compliance, featuring advanced leak detection systems and secure payment options. Additionally, they are built to withstand the most challenging environments, reducing downtime and maintenance costs.

In summary, the Wayne 3014, 3018, 3018DLX, and 3514 are more than just dispensers; they represent the future of fueling technology. With their focus on user experience, adaptability, and operational efficiency, these models are set to redefine fuel dispensing in the retail sector. Achieving success in a competitive market is easier with equipment designed to deliver outstanding performance and reliability.
Top Page Image Contents