Wayne 3514 Mounting Door Bracket, Installing Light, Installing Wired Wall Station if included

Page 13

Step 6: Mounting Door Bracket

WARNING: Fiberglass, aluminum and steel doors must be reinforced to prevent damage to the door. Check with your ga- rage door manufacturer for their recom- mendations.

Reinforce light weight doors, as illustrated.

For wood doors, mount door bracket, using two 1/4”-20 x 2” carriage bolts and 1/4” nuts supplied, on center line of door with middle hole in line with top rollers.

For metal doors, mount door bracket, using two 1/4”-20 x 1/2” self drilling screws supplied, on center line of door with middle hole in line with top rollers.

Step 7: Installing Light

Remove diffuser cover by pressing on both sides of the bottom of the lighting cover at the junction of the housing, releasing the locking tabs, and pulling forward. Screw a 60 Watt bulb (60 Watt Maximum) into socket. For maximum bulb life, “rough service” bulbs are recom- mended. Align top and bottom tabs on cover to Motor Power Head Unit and push straight on until cover locks into place.

Note: light turns on automatically when door is activated and a 4 minute time delay circuit automatically turns light off, allowing am- ple time to enter the house. A fully open door with light blinking indicates an obstruction or problems with external safety sensors during close travel. See trouble shooting section for further details.

Step 8: Installing Wired Wall Station (if included)

WARNING: Install all wall controls out of the reach of children and in a location where the door can be seen before activating. Do not mount wall controls near or next to garage door.

Wired Wall Station: Wire the garage door opener wall station using bell wire (low voltage electrical wire) connected to COM and P.B. on vertical screw terminal strips, as illustrated.

Locate push button adjacent to service entrance door at a minimum height of 5 ft., and at least 5 ft. away from garage door (see illustration in Step 10). Fasten the wall station in a safe location with the (2) Phillips head screws, making sure not to over tighten. Pilot drill mounting holes

using a 3/32" bit. Additional wired wall stations may also be installed in accordance with these instructions.

CAUTION: Over tightening the screws could deform plastic.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Owner Installation Important Installation Instructions Page Before Starting FeaturesDoor Test One Door Tests Before StartingTools You’ll Need Part Identification Hardware Identification Step One Rail Assembly Rail AssemblyStep Three Mounting Front Rail Assembly Step Two Trolley AlignmentStep Five Setting The Chain Latch Assembly Step Four Setting The ChainStep Six Rail Assembly Alignment Positioning and Installing Front Wall Bracket Attaching Motor Power Head Unit to RailPositioning the Motor End of Operator Attach Unit to Front Wall BracketMounting Motor End of Opener Installing Wired Wall Station if included Installing LightMounting Door Bracket Install Entrapment Warning Label Installing Deluxe Wireless Wall Station if includedInstall Wireless Infrared Safety Sensor Install Wireless Infrared Safety Sensor BracketInstall Wired Infrared Safety Sensor Wall Mounting Brackets Connecting Wired Infrared Safety Sensor to Opener Install Wiring for Wired Infrared Safety SensorConnecting Electrical Power Mount Wired Infrared Safety SensorsChanging Wireless Wall Station Code Wireless Wall Station Security Code Change and ProgrammingAlignment of the Wireless Infrared Safety Sensors Changing the Transmitter Code Alignment of the Wired Infrared Safety SensorsTwo Button Transmitter Security Code Change and Programming Programming Transmitter to Power Head UnitSetting Trolley Close Position Connecting Cushion Arm to TrolleyIMPORTANT! Test Contact Obstruction Sensing Feature Connecting Door Arm to DoorInfrared Safety Sensor Obstruction Test Setting Door Opening TravelInstalling Wireless Keyless Entry If Included Programming Wireless Keyless Entry If IncludedAdjustment # 1 Opening and Closing Force AdjustmentsAdjustment # 3 Positive Mechanical Door Lock Adjustment # 2 Contact Obstruction Sensing Closing DirectionImportant Safety Instructions Operation of Your Opener HOW to Operate the Wireless Keyless Entry if IncludedOpener Power Head Controls HOW to Operate the Wireless Wall Station If IncludedPage Twice a Year Once a MonthOnce a Year Trouble Shooting Section Parts Breakdown Rail Assembly All Models Description Per Unit # Per Unit Classicdrive Accessories Pre-drill a 5/64 pilot Hole 3/4 deep Cut Template to Aid in Keyless Entry Installation See StepLimited Lifetime Warranty Questions?

3514, 3014, 3018, 3018DLX specifications

Wayne 3014, 3018, 3018DLX, and 3514 are a series of innovative fuel dispensers designed to cater to the evolving needs of the retail fueling industry. These models embody advanced engineering, reliability, and efficiency, making them ideal solutions for gas station operators looking to enhance their service offerings.

The Wayne 3014 series is characterized by its compact design, making it a perfect fit for locations with space constraints. It features a user-friendly interface, which allows for easier interaction for both attendants and customers. The sleek and modern look of the 3014 gives stations a contemporary feel while maintaining durability against the elements.

The 3018 model builds on the robust foundation of the 3014 but adds additional features for increased throughput. With capabilities to handle multiple products, the 3018 allows for various fuel types to be dispensed efficiently, catering to the diverse needs of customers. The model is equipped with advanced metering technologies, ensuring accurate measurement and reducing loss through evaporation or spillage.

For those seeking a more premium option, the 3018DLX stands out with its enhanced features and aesthetics. It offers an integrated payment system, supporting both card and mobile payments, which vastly improves transaction speed and customer satisfaction. The dispenser is also designed with a customizable interface that allows operators to promote special offers or loyalty programs directly on the screen.

The Wayne 3514 takes technology a notch higher, incorporating robust software support that enables real-time data analytics. This feature allows station owners to monitor sales trends and inventory levels efficiently, leading to optimized operations and better decision-making. The 3514 also supports future upgrades, ensuring that the infrastructure can adapt as technology evolves.

All these models prioritize safety and regulatory compliance, featuring advanced leak detection systems and secure payment options. Additionally, they are built to withstand the most challenging environments, reducing downtime and maintenance costs.

In summary, the Wayne 3014, 3018, 3018DLX, and 3514 are more than just dispensers; they represent the future of fueling technology. With their focus on user experience, adaptability, and operational efficiency, these models are set to redefine fuel dispensing in the retail sector. Achieving success in a competitive market is easier with equipment designed to deliver outstanding performance and reliability.
Top Page Image Contents