Wayne 3014, 3514, 3018DLX user manual Trouble Shooting Section

Page 34

TROUBLE SHOOTING SECTION

SYMPTOM

PROBABLE CAUSE

CORRECTIVE ACTION

Opener won’t work from wall button or

No power to opener.

Check cord to outlet, wall switch and

radio control.

 

circuit breaker.

 

Short circuit in wires to opener or wall

Isolate by disconnecting the wires at

 

button.

the opener from the wall station.

 

Motor Protector trips open due to ex-

Allow motor to cool for 20 minutes and

 

cessive use.

try again.

Opener works from wall button but not

Radio control system non-operational.

Weak or dead battery in transmitter-

from radio control.

 

replace.

 

 

Security Code not matched between

 

 

receiver and transmitter (see page 21)

 

 

If two or more transmitters don’t work,

 

 

have Motor Control Board Tested.

Door does not open and opener light

Something obstructing door travel.

Disconnect door from operator. Oper-

flashes.

 

ate door by hand to locate obstruction

 

 

or call a service person.

 

Insufficient opening force.

Adjust opening force. (See Adj. #1).

 

Build up of ice and snow around door.

Shovel and clear door area.

Door does not open fully and light

Open Limit not set properly.

Adjust Open Travel with screwdriver,

does not flash.

 

turn counter-clockwise to desired set-

 

 

ting. 1/4 turn equals to 1” of travel (see

 

 

Step 28).

Door stops and does not close fully.

Close Limit not set properly.

Adjust Close Travel with screwdriver,

 

 

turn clockwise to desired setting. 1/4

 

 

turn equals 1” of travel (See Step 27).

Door closes and then returns to fully

Door arm adjustment.

Adjust rod in tube to provide 1” of

open position and opener light flashes.

 

“cushion” compression when door is

 

 

fully closed (See Step 24 and 26).

 

Close travel adjustment is set beyond

Adjust Close Travel with screwdriver,

 

normal door position.

turn clockwise to desired setting. 1/4

 

 

turn equals 1” of travel (See Step 27).

 

Obstructions on floor.

Check for stones or ice under door

 

 

and remove.

When activated with door in fully open

Infrared Safety Sensors out of adjust-

Infrared Safety Sensors alignment

position, door travels for 1 second,

ment or defective.

should be checked per instructions.

stops, and returns to fully open posi-

 

(See Step 21 and 22).

tion and light begins to flash.

Batteries in Wireless Safety Sensors.

Check batteries and contact points.

 

 

Obstructions in door opening.

Check for object blocking Infrared

 

 

Safety Sensors.

Door reverses travel before reaching

Activation of obstruction sensing sys-

Check for binding in door travel (door

fully closed position and opener light

tem.

“stops”, door tracks, etc).

flashes.

Loose or hanging objects on door acti-

Remove objects.

 

 

vating Infrared Safety Sensor

 

 

Insufficient closing force.

Adjust closing force. (See Adj. #1).

Door stops travel for 1 second at mid-

Weak battery in Wireless Infrared

Replace batteries in Wireless Infrared

point during close and then continues

Safety Sensors.

Safety Sensors.

to close.

 

 

Door fully opens and then light flashes.

Open limit is set too high and trolley is

Adjust Open Travel with screwdriver,

 

hitting the stop bolt.

turn counter-clockwise to desired set-

 

 

ting. 1/4 turn equals to 1” of travel (see

 

 

Step 28).

 

34

 

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Owner Installation Important Installation Instructions Page Features Before StartingDoor Tests Before Starting Door Test OneTools You’ll Need Part Identification Hardware Identification Step Three Mounting Front Rail Assembly Rail AssemblyStep One Rail Assembly Step Two Trolley AlignmentStep Five Setting The Chain Latch Assembly Step Four Setting The ChainStep Six Rail Assembly Alignment Attaching Motor Power Head Unit to Rail Positioning and Installing Front Wall BracketPositioning the Motor End of Operator Attach Unit to Front Wall BracketMounting Motor End of Opener Installing Wired Wall Station if included Installing LightMounting Door Bracket Installing Deluxe Wireless Wall Station if included Install Entrapment Warning LabelInstall Wireless Infrared Safety Sensor Bracket Install Wireless Infrared Safety SensorInstall Wired Infrared Safety Sensor Wall Mounting Brackets Install Wiring for Wired Infrared Safety Sensor Connecting Wired Infrared Safety Sensor to OpenerMount Wired Infrared Safety Sensors Connecting Electrical PowerWireless Wall Station Security Code Change and Programming Changing Wireless Wall Station CodeAlignment of the Wireless Infrared Safety Sensors Alignment of the Wired Infrared Safety Sensors Changing the Transmitter CodeProgramming Transmitter to Power Head Unit Two Button Transmitter Security Code Change and ProgrammingConnecting Cushion Arm to Trolley Setting Trolley Close PositionConnecting Door Arm to Door IMPORTANT! Test Contact Obstruction Sensing FeatureSetting Door Opening Travel Infrared Safety Sensor Obstruction TestProgramming Wireless Keyless Entry If Included Installing Wireless Keyless Entry If IncludedAdjustments Adjustment # 1 Opening and Closing ForceAdjustment # 2 Contact Obstruction Sensing Closing Direction Adjustment # 3 Positive Mechanical Door LockImportant Safety Instructions HOW to Operate the Wireless Keyless Entry if Included Operation of Your OpenerHOW to Operate the Wireless Wall Station If Included Opener Power Head ControlsPage Twice a Year Once a MonthOnce a Year Trouble Shooting Section Parts Breakdown Rail Assembly All Models Description Per Unit # Per Unit Classicdrive Accessories Cut Template to Aid in Keyless Entry Installation See Step Pre-drill a 5/64 pilot Hole 3/4 deepLimited Lifetime Warranty Questions?

3514, 3014, 3018, 3018DLX specifications

Wayne 3014, 3018, 3018DLX, and 3514 are a series of innovative fuel dispensers designed to cater to the evolving needs of the retail fueling industry. These models embody advanced engineering, reliability, and efficiency, making them ideal solutions for gas station operators looking to enhance their service offerings.

The Wayne 3014 series is characterized by its compact design, making it a perfect fit for locations with space constraints. It features a user-friendly interface, which allows for easier interaction for both attendants and customers. The sleek and modern look of the 3014 gives stations a contemporary feel while maintaining durability against the elements.

The 3018 model builds on the robust foundation of the 3014 but adds additional features for increased throughput. With capabilities to handle multiple products, the 3018 allows for various fuel types to be dispensed efficiently, catering to the diverse needs of customers. The model is equipped with advanced metering technologies, ensuring accurate measurement and reducing loss through evaporation or spillage.

For those seeking a more premium option, the 3018DLX stands out with its enhanced features and aesthetics. It offers an integrated payment system, supporting both card and mobile payments, which vastly improves transaction speed and customer satisfaction. The dispenser is also designed with a customizable interface that allows operators to promote special offers or loyalty programs directly on the screen.

The Wayne 3514 takes technology a notch higher, incorporating robust software support that enables real-time data analytics. This feature allows station owners to monitor sales trends and inventory levels efficiently, leading to optimized operations and better decision-making. The 3514 also supports future upgrades, ensuring that the infrastructure can adapt as technology evolves.

All these models prioritize safety and regulatory compliance, featuring advanced leak detection systems and secure payment options. Additionally, they are built to withstand the most challenging environments, reducing downtime and maintenance costs.

In summary, the Wayne 3014, 3018, 3018DLX, and 3514 are more than just dispensers; they represent the future of fueling technology. With their focus on user experience, adaptability, and operational efficiency, these models are set to redefine fuel dispensing in the retail sector. Achieving success in a competitive market is easier with equipment designed to deliver outstanding performance and reliability.
Top Page Image Contents