Wayne 3014, 3514, 3018 Attach Unit to Front Wall Bracket, Positioning the Motor End of Operator

Page 12

Step 3: Attach Unit to Front Wall Bracket

Raise the front end of the opener and attach it to the front wall bracket, using the ¼” x 4” hex head bolt and the supplied ¼” plastic insert nut. Take care not to over tighten nut; tighten only until end of bolt is flush with out- side of nut.

NOTE: If you have a torsion spring counter-balance system, it will be necessary to raise the motor Head Assembly of the opener and support it on a step-ladder to attach the front end of the opener to Wall Bracket.

Step 4: Positioning the Motor End of Operator

CAUTION: To prevent damage to steel, aluminum, fiberglass or glass panel doors do not rest the opener of the door without using a 2” x 4” at least 12” long.

Raise the motor end of the opener and support it so you can open the door to its fully open position. You may need help raising motor end if ladder is not high enough.

Open the door and place a 2” x 4” piece of wood along the top section of the garage door. Rest the double rails on the 2” x 4”, as illustrated.

Support the top section of the door to prevent sagging.

Step 5: Mounting Motor End of Opener

Align the center of opener tracks with the center line previously marked on the top section of the garage door to ensure rail will be parallel with the di- rection of door travel.

Use perforated hangers (cut as needed to adjust length) from ceiling or beams to hang opener at motor end (be sure to locate and mount to solid structural beams, as illustrated). Pre-drill with 3/16” drill bit and use 1/4” x 1-1/2” lag screws to ensure a rigid mount. Attach opener to hangers.

WARNING: Do not use gear cap bolt or nut for hanger attachment, this may cause sprocket and chain misalignment, resulting in damage or possible injury!

Note: Hanging brackets should be at an angle to provide rigid support. If hangers have no angle or if you use long hangers, cross brace the hangers to eliminate the possibility of sway during operation of the opener.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Owner Installation Important Installation Instructions Page Features Before StartingDoor Tests Before Starting Door Test OneTools You’ll Need Part Identification Hardware Identification Rail Assembly Step One Rail AssemblyStep Three Mounting Front Rail Assembly Step Two Trolley AlignmentStep Four Setting The Chain Step Five Setting The Chain Latch AssemblyStep Six Rail Assembly Alignment Attaching Motor Power Head Unit to Rail Positioning and Installing Front Wall BracketAttach Unit to Front Wall Bracket Positioning the Motor End of OperatorMounting Motor End of Opener Installing Light Installing Wired Wall Station if includedMounting Door Bracket Installing Deluxe Wireless Wall Station if included Install Entrapment Warning LabelInstall Wireless Infrared Safety Sensor Bracket Install Wireless Infrared Safety SensorInstall Wired Infrared Safety Sensor Wall Mounting Brackets Install Wiring for Wired Infrared Safety Sensor Connecting Wired Infrared Safety Sensor to OpenerMount Wired Infrared Safety Sensors Connecting Electrical PowerWireless Wall Station Security Code Change and Programming Changing Wireless Wall Station CodeAlignment of the Wireless Infrared Safety Sensors Alignment of the Wired Infrared Safety Sensors Changing the Transmitter CodeProgramming Transmitter to Power Head Unit Two Button Transmitter Security Code Change and ProgrammingConnecting Cushion Arm to Trolley Setting Trolley Close PositionConnecting Door Arm to Door IMPORTANT! Test Contact Obstruction Sensing FeatureSetting Door Opening Travel Infrared Safety Sensor Obstruction TestProgramming Wireless Keyless Entry If Included Installing Wireless Keyless Entry If IncludedAdjustments Adjustment # 1 Opening and Closing ForceAdjustment # 2 Contact Obstruction Sensing Closing Direction Adjustment # 3 Positive Mechanical Door LockImportant Safety Instructions HOW to Operate the Wireless Keyless Entry if Included Operation of Your OpenerHOW to Operate the Wireless Wall Station If Included Opener Power Head ControlsPage Once a Month Twice a YearOnce a Year Trouble Shooting Section Parts Breakdown Rail Assembly All Models Description Per Unit # Per Unit Classicdrive Accessories Cut Template to Aid in Keyless Entry Installation See Step Pre-drill a 5/64 pilot Hole 3/4 deepLimited Lifetime Warranty Questions?

3514, 3014, 3018, 3018DLX specifications

Wayne 3014, 3018, 3018DLX, and 3514 are a series of innovative fuel dispensers designed to cater to the evolving needs of the retail fueling industry. These models embody advanced engineering, reliability, and efficiency, making them ideal solutions for gas station operators looking to enhance their service offerings.

The Wayne 3014 series is characterized by its compact design, making it a perfect fit for locations with space constraints. It features a user-friendly interface, which allows for easier interaction for both attendants and customers. The sleek and modern look of the 3014 gives stations a contemporary feel while maintaining durability against the elements.

The 3018 model builds on the robust foundation of the 3014 but adds additional features for increased throughput. With capabilities to handle multiple products, the 3018 allows for various fuel types to be dispensed efficiently, catering to the diverse needs of customers. The model is equipped with advanced metering technologies, ensuring accurate measurement and reducing loss through evaporation or spillage.

For those seeking a more premium option, the 3018DLX stands out with its enhanced features and aesthetics. It offers an integrated payment system, supporting both card and mobile payments, which vastly improves transaction speed and customer satisfaction. The dispenser is also designed with a customizable interface that allows operators to promote special offers or loyalty programs directly on the screen.

The Wayne 3514 takes technology a notch higher, incorporating robust software support that enables real-time data analytics. This feature allows station owners to monitor sales trends and inventory levels efficiently, leading to optimized operations and better decision-making. The 3514 also supports future upgrades, ensuring that the infrastructure can adapt as technology evolves.

All these models prioritize safety and regulatory compliance, featuring advanced leak detection systems and secure payment options. Additionally, they are built to withstand the most challenging environments, reducing downtime and maintenance costs.

In summary, the Wayne 3014, 3018, 3018DLX, and 3514 are more than just dispensers; they represent the future of fueling technology. With their focus on user experience, adaptability, and operational efficiency, these models are set to redefine fuel dispensing in the retail sector. Achieving success in a competitive market is easier with equipment designed to deliver outstanding performance and reliability.
Top Page Image Contents