Preliminary Installation Notes | Vector VEC049C instruction

PRELIMINARY INSTALLATION NOTES:

The inverter has four slots in its mounting bracket that allow the unit to be fastened against a bulkhead, floor, wall or other flat surface. Ideally, the mounting surface should be cool to the touch. It is more electrically efficient to use longer AC wiring than DC wiring, so install the inverter as close as possible to the 12VDC power source.

Vector inverters can be operated in any position, however, if it is to be mounted on a wall, mount it horizontally so that indicators, switches, outlets and terminal blocks on the front panel are visible and accessible.

1)If inverter is to be installed in a vehicle, Vector recommends that the inverter be shock mounted to either the floor (in a clear, safe area) or on a secure flat surface.

2)Locate a convenient place to mount the inverter and fuse holder.

3)Perform a test routing of the proposed cable length, but don’t do any cutting at this time. (FIGURE 7)

4)Be sure that the positive (+) and negative (-) cables to the battery DO NOT exceed 6 feet.

5)Using a specified AWG cable, reposition the inverter and fuse holder if necessary.

6)After you have practiced the above preliminary installation steps, proceed with the “actual” inverter installation.

After you have selected an appropriate location for the inverter and fuse block, proceed with the actual installation of the inverter.

Contact Vector® Manufacturing for any further installation information or questions. You can purchase fuses, fuse holders, specific cable or cable battery connectors from your local electrical supplier or call Vector Technical Support toll-free (866) 584-5504.

This procedure is for using locally purchased supplies. Make appropriate changes to procedure if Vector Cable Set is purchased.

5.5.2 PERMANENT INSTALLATION PROCEDURES

The cables between the power source and inverter should be as shown in FIGURE 7 (Page 13). Remove terminal cover and terminal nuts before starting permanent installation.

Inverter DC cables and fuse installation are as follows:

1.Using tools and hardware, mount the inverter to a flat surface.

2.Mount the fuse holder to its mounting surface using appropriate hardware. Ensure that mounting hardware does not touch any fuse holder or fuse con- tacts. Ensure that fuse is removed from its holder.

3.Measure the cable twice before cutting the cable.

4.Cut one cable length to connect the negative (–) battery terminal and the inverter’s negative terminal, leaving a little slack in the cable.

5.Cut another cable to connect the positive (+) battery terminal to one side of fuse holder, leaving a little slack.

6.Cut the final cable to connect the other side of fuse holder to the positive (+) terminal on the inverter back panel.

7.Strip the insulation of the three cables to 1-inch (2.45 cm) .

8.Crimp or sweat-solder the copper strands to ring terminals. For safety, do this in an open space because it may require the use of a propane torch.

VEC049C specifications

The Vector VEC049C is a sophisticated and portable power inverter designed for rugged automotive and emergency applications. This inverter converts 12V DC battery power into a stable 120V AC power source, making it ideal for powering a variety of electronic devices while on the go. It serves as an essential tool for outdoor enthusiasts, travelers, and those in need of backup power solutions during emergencies.

One of the main features of the VEC049C is its robust construction, which ensures durability in challenging environments. This inverter is equipped with multiple output options, including standard AC outlets as well as USB ports, catering to a wide array of devices such as laptops, smartphones, and small appliances. Its capacity to deliver up to 400 watts of continuous power makes it suitable for charging devices or running equipment like lights and fans.

The Vector VEC049C incorporates advanced technology to enhance both performance and safety. The unit features built-in protection mechanisms against overload, short-circuit, and over-temperature, providing peace of mind during operation. Furthermore, the inverter employs a modified sine wave output, which is often sufficient for less sensitive electronics and ensures efficient energy conversion.

The design of the VEC049C is both compact and lightweight, allowing for easy transport and storage. Users can conveniently stow it in their vehicle or carry it in a backpack, making it a practical option for road trips, camping adventures, and outdoor activities. The unit can easily be plugged into a car’s 12V outlet, allowing for easy access to power whenever it's needed.

In terms of user-friendliness, the Vector VEC049C features an LED status indicator that provides real-time information about the power condition and operation status. This usability aspect is crucial for individuals who may not have technical backgrounds but require reliable power solutions.

Overall, the Vector VEC049C stands out for its combination of portability, safety features, and versatility. With its capacity to bridge the gap between 12V DC and 120V AC power needs, this inverter is an invaluable asset for anyone seeking reliable energy solutions in a mobile format. Whether on a road trip, at a campsite, or during a power outage, the VEC049C ensures that essential devices remain operational and accessible.