Vector VEC049C owner manual Installation, Input Power Requirements, Operating Environment

Page 13

5.0INSTALLATION

MAXX SST™ inverters will provide you with various watts of continuous, electrical power (See Models Specification Chart Page 18) when powered by a 12VDC source such as is found in a vehicle or multiple battery configuration as shown in FIGURE 7. This manual does not describe all of the possible types of battery, battery charging, and battery isolation configurations.

5.1 INPUT POWER REQUIREMENTS:

To properly operate the inverter, the DC power source must provide between

10.5and 15.5VDC and nominally at 150 Amps. This DC power source must be a well-regulated DC power supply as typically found in vehicle and deep-cycle marine batteries. The DC power source may also be two 12 volt batteries connected in parallel. On larger applications the power source may be several batteries connected in parallel as shown on FIGURE 7.

Figure 7 –Battery Wiring

NOTE: Vector® Manufacturing recommends that for typical heavy-duty uses, a specified or equivalent main buss fuse (See Page 18) be added as close as possible to the power source (battery) positive terminal. The fuse amperage must be sized to allow simultaneous operation of all the AC appliances to be powered, with delay characteristics that allow for the momentary high start-up current requirements of inductive loads. Use the recommended fuse block (fuse holder) and fuse, or an electrical equivalent. For full rated output and motor start-up surge output, ensure that the installation is configured to handle the full load. FIGURE 7 is also used as a guide when the cables are measured for installing the inverter; available through Vector Technical Support toll-free at (866) 584-5504.

5.2 OPERATING ENVIRONMENT

WARNINGS: DO NOT locate inverters in an area, room or compartment where explosive or flammable fumes might be present. Areas such as: engine room, engine compartment, boat, and small, unvented battery compartments.

13

Image 13
Contents Maxx Ssttm Read ALL Instructions Before Using this Power Inverter Important Safety InformationNo USER-SERVICEABLE Components Inside Important Cable InformationContents Basic Tour of the Maxx SST Model Inverter IntroductionBUILT-IN Automatic Safety Features Include Maxx SST Safety FeaturesAppliance Cautions Inverter Applications Uninterruptible Power Supply UPSModified Square Wave and Sine Wave Comparison Theory of OperationOperation Power RequirementsAppliance Battery Operating Time Determining Battery SizeLOW Battery Alarm Protective FeaturesInput Power Requirements InstallationOperating Environment Installation Sequence Permanent Installation Test ProcedureQuick Operational Checkout or Emergency USE YOU will NeedInverter DC cables and fuse installation are as follows Preliminary Installation NotesDo not connect this wire to the negative DC input terminal Power Inverter Model SpecificationsTroubleshooting Service & PartsCommon Problems Power Tools and Microwave Ovens WON’T StartTroubleshooting Guide MaintenanceVector 2 Year Limited Warranty Program Warranty

VEC049C specifications

The Vector VEC049C is a sophisticated and portable power inverter designed for rugged automotive and emergency applications. This inverter converts 12V DC battery power into a stable 120V AC power source, making it ideal for powering a variety of electronic devices while on the go. It serves as an essential tool for outdoor enthusiasts, travelers, and those in need of backup power solutions during emergencies.

One of the main features of the VEC049C is its robust construction, which ensures durability in challenging environments. This inverter is equipped with multiple output options, including standard AC outlets as well as USB ports, catering to a wide array of devices such as laptops, smartphones, and small appliances. Its capacity to deliver up to 400 watts of continuous power makes it suitable for charging devices or running equipment like lights and fans.

The Vector VEC049C incorporates advanced technology to enhance both performance and safety. The unit features built-in protection mechanisms against overload, short-circuit, and over-temperature, providing peace of mind during operation. Furthermore, the inverter employs a modified sine wave output, which is often sufficient for less sensitive electronics and ensures efficient energy conversion.

The design of the VEC049C is both compact and lightweight, allowing for easy transport and storage. Users can conveniently stow it in their vehicle or carry it in a backpack, making it a practical option for road trips, camping adventures, and outdoor activities. The unit can easily be plugged into a car’s 12V outlet, allowing for easy access to power whenever it's needed.

In terms of user-friendliness, the Vector VEC049C features an LED status indicator that provides real-time information about the power condition and operation status. This usability aspect is crucial for individuals who may not have technical backgrounds but require reliable power solutions.

Overall, the Vector VEC049C stands out for its combination of portability, safety features, and versatility. With its capacity to bridge the gap between 12V DC and 120V AC power needs, this inverter is an invaluable asset for anyone seeking reliable energy solutions in a mobile format. Whether on a road trip, at a campsite, or during a power outage, the VEC049C ensures that essential devices remain operational and accessible.