Integra DTR-5.9 instruction manual Specifications, 113

Page 113

Specifications

Amplifier Section

Rated Output Power

North American:

90 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20Hz to 20kHz, with a maximum total harmonic distortion of 0.08% (FTC)

105 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven at 1kHz, with a maximum total harmonic distortion of 0.7% (FTC)

110 watts minimum continuous power per channel, 6 ohm loads, 2 channels driven at 1kHz, with a maximum total harmonic distortion of 0.1% (FTC)

Oceanian:

7 ch ⋅ 175 W at 6 ohms, 1kHz, 1 ch driven (JEITA)

Dynamic Power

210 W (3Ω, Front)

 

180 W (4Ω, Front)

 

110 W (8Ω, Front)

THD (Total Harmonic

 

Distortion)

0.08% (Power Rated)

 

0.08% (20Hz to 20kHz Power Rated)

Damping Factor

60 (Front, 1kHz, 8Ω)

Input Sensitivity and

200 mV/ 47 kΩ (LINE)

Impedance

Output Level and

200 mV/ 2.2 kΩ (REC OUT)

Impedance

Frequency Response

5Hz–100kHz/ +1 dB–3 dB (direct mode)

Tone Control

±10 dB, 50Hz (BASS)

 

±10 dB, 20kHz (TREBLE)

Signal to Noise Ratio

106 dB (LINE, IHF-A)

Speaker Impedance

 

North American:

6Ω–16Ω

Oceanian:

4Ω–16Ω

Video Section

Input Sensitivity/Output

Level and Impedance 1 Vp-p /75Ω(Component and S-Video Y)

0.7Vp-p /75Ω(Component Pb/Cb, Pr/Cr)

0.28Vp-p /75Ω(S-Video C) 1 Vp-p /75Ω(Composite)

Component Video

 

Frequency Response

5Hz – 50MHz, –3 dB

Tuner Section

■FM

Tuning Frequency Range

North American: 87.5MHz–107.9MHz

Asian and Oceanian: 87.50MHz–108.00MHz, RDS

■AM

Tuning Frequency Range

North American: 530kHz–1710kHz

Asian and Oceanian: 522kHz–1611kHz

■Digital Tuner

North American:

SIRIUS

Preset Channel

40

General

Power Supply

 

North American:

AC 120 V, 60Hz

Asian and Oceanian:

AC 230 V, 50Hz

Power Consumption

 

North American:

5.5 A

Asian and Oceanian:

550 W

Dimensions

435 ⋅ 173 ⋅ 391 mm

(W ⋅ H ⋅ D)

 

17-1/8" ⋅ 6-13/16"⋅15-3/8"

Weight

 

North American:

11.6 kg

 

25.6 lbs.

Asian and Oceanian:

11.5 kg, 25.4 lbs.

■Video Inputs

HDMI (Assignable)

IN 1, IN 2, IN 3, IN 4

Component

IN 1, IN 2

Composite

DVD, VCR/DVR, CBL/SAT, GAME/TV,

 

AUX

S-Video

DVD, VCR/DVR, CBL/SAT, GAME/TV

■Video Outputs

HDMI

OUT

Component

OUT

Composite

MONITOR OUT, VCR/DVR (REC OUT)

S-Video

MONITOR OUT, VCR/DVR (REC OUT)

■Audio Inputs

Digital Inputs

 

(Assignable)

2 (Rear OPT), 2 (Rear coax)

Analog Inputs

DVD (MULTICHANNEL), VCR/DVR,

 

CBL/SAT, GAME/TV, AUX, TAPE, CD

Multichannel Inputs

7.1 ch

■Audio Outputs

Digital Outputs

1 (Optical)

Analog Outputs

TAPE, VCR/DVR, ZONE 2

Multichannel Pre

 

Outputs

7ch

Subwoofer Pre Outputs

1

Speaker Outputs

Main (L, R, C, SL, SR, SBL, SBR)

 

+ ZONE2 (L, R)

Phones

1

■Control Terminal

Mic

Yes

RS232

1

Ether

1

IR Input/Output

2/1

12V Trigger Out

3

Specifications and features are subject to change without notice.

113

Page 112 Page 114
Image 113
Page 112 Page 114
Contents DTR-5.9 Avis Important Safety InstructionsFCC Information for User PrecautionsPower Contents Supplied AccessoriesContents Amplifier FeaturesProcessing ConnectionsZone 2 Room Multiroom CapabilityMain Room Front Panel Getting to Know the AV ReceiverDisplay Getting to Know the AV ReceiverDigital in Coaxial 1 Rear PanelComponent Video in 1 Hdmi in 1-4 and OUTIR in A/B and OUT Sirius antenna on North American modelRS232 Digital Optical in 1, 2, and OUTButton Muting buttonAudio button Sleep buttonUsing the Remote Controller Remote ControllerInstalling the Batteries Enjoying Home Theater Connecting Your SpeakersSubwoofer Surround back left and right speakersSpeaker Configuration Connecting Your SpeakersUsing Dipole Speakers Connecting a Powered Subwoofer Speaker Connection PrecautionsAttaching the Speaker Labels Speaker ColorStrip about 5/8 Connecting the Speaker CablesBi-amping Speaker Hookup Bi-amping Front SpeakersConnecting the Indoor FM Antenna Connecting AntennasConnecting the AM Loop Antenna Attach the FM antenna, as shown American ModelConnecting an Outdoor FM Antenna Connecting AntennasConnecting an Outdoor AM Antenna Using a TV/FM Antenna SplitterAbout AV Connections Connecting Your ComponentsOptical Digital Jacks AV Connection Color CodingConnecting Audio and Video Signals to the AV Receiver Connecting Your ComponentsWhich Connections Should I Use? Audio Connection FormatsTV, projector, etc Signal Selection Example DVD player, etc Video Signal Flow Chart DVD player, etcVideo Connection Formats TV, projector, etcVideo Connection Connecting a TV or ProjectorAudio Connection HintDVD player Connecting a DVD playerHooking Up the Multichannel Input VCR or DVR Connecting a VCR or DVR for PlaybackConnecting a VCR or DVR for Recording CBL/SAT in S Game Console Connecting a Game ConsoleAbout Hdmi Connecting Components with HdmiSupported Audio Formats About Copyright ProtectionMaking Hdmi Connections Video SignalsAudio Signals Make the video connection a Make the audio connection a Connecting a Camcorder or Other DeviceConnecting a Power Amplifier CD Player or Turntable MM with Built-in Phono Preamp Step Connecting a CD Player or TurntableCD player CD or turntableConnecting a Cassette, CDR, MiniDisc, or DAT Recorder Not all iPod models output video Connecting an RI DockIf Your iPod Supports Video If Your iPod Doesn’t Support VideoAuto Power On/Standby Connecting Integra/Onkyo ComponentsRemote Control Direct ChangeDo the automatic speaker setup-this is essential Connecting the Power CordTurning On the AV Receiver Turning On and StandbyAutomatic Speaker Setup First Time SetupUsing Audyssey 2EQ Measurement PositionsFollowing screen appears First Time SetupPress Enter Error Messages Changing the Speaker Settings Manually To Retry the Automatic Speaker SetupUsing a Powered Subwoofer Write ErrorSpeaker Settings Main menu appears onscreen Hdmi Input SetupSure the appropriate external input is Selected on your TVPress the Receiver button, fol- lowed by the Setup button Component Video Input SetupDigital Input Setup Changing the Input Display Automatic Audio Input Selection Setup Playing Your AV Components Select a listening mode and enjoyBasic AV Receiver Operation Start playback on the source componentUsing the Sleep Timer Setting the Display BrightnessCommon Functions Muting the AV ReceiverDisplaying Source Information 7Using HeadphonesCommon Functions Preset Enter Specifying the Digital Signal FormatButtons to select 7. Hardware AM Frequency Step Setup on some modelsListening to the Radio Listening to the Radio Tuning into AM/FM Radio StationsListening to AM/FM Stations Use the Tuner input selector button to select AM or FMListening mode Tuning into Stations by FrequencyDisplaying AM/FM Radio Information DisplayDeleting Presets Selecting PresetsWhat is Sirius Satellite Radio? Setting Up the SiriusConnect Home TunerPositioning the Antenna Important Sirius Satellite Radio InformationMode button, followed by Setting the Satellite Radio ModeUse the Up and Down Buttons to select SAT Radio Mode When you’ve finished, pressSelecting Sirius Satellite Radio Channels Signing Up for Sirius Satellite RadioPresetting Sirius Channels Buttons to select 3. Tuner, and then press Enter Setup Enter Number buttonsParental Lock Changing the PIN Number New 4-digit PIN number Use the Left and Right Old 4-digit PIN number Use the Left and RightDigits in the new PIN number Confirm the new PIN number byPositioning the SiriusConnect Home Antenna Displaying Sirius Satellite Radio InformationAcquiring Sirius Satellite Radio MessagesRDS Program Types PTY Using RDS European models onlyWhat is RDS? Finding Stations by Type PTY Displaying Radio Text RTListening to Traffic News TP Selecting with the Remote Controller Using the Listening ModesSelecting the Listening Modes Selecting on the AV ReceiverAnalog and PCM Sources Using the Listening ModesListening Modes Available for Each Source Format Dolby Digital and Dolby Digital Plus Sources DTS DTS SourcesTrueHD Sources DTS-HD Sources DSD DTS Express and DSD SourcesAbout the Listening Modes Onkyo Original DSP Modes Recording from Different AV Sources RecordingRecording the Input Source Using the Audio Adjust Settings Adjusting the Listening ModesMultiplex/Mono Settings PLIIx/Neo6 SettingsTheater-Dimensional Setting Adjusting the Listening ModesDolby EX Settings Tone Control Settings Using the Audio SettingsLate Night Function CinemaFILTERSpeaker Levels Audyssey Dynamic EQMusic Optimizer SyncListening Mode Presets Speaker Setup Advanced SetupLow-Pass Filter for the LFE Channel Advanced SetupSelect a crossover frequency Use the Down button toSpeaker Distance Double BassPink noise test tone is output by the front left speaker Setup menu closes Equalizer SettingsIntelliVolume Source SetupOSD Setup Miscellaneous SetupVolume Setup Remote Control Hardware SetupAnalog Multich ZoneTuner Lip Sync Audio TV OutColor ControlNetwork Lock SetupConnecting Your Zone 2 Speakers Directly to the AV receiver Connecting ZoneConnecting Your Zone 2 Speakers to an Amp in Zone ZoneButtons to select 2. Zone2, Powered Zone 2 SettingIf you’ve connected your Zone 2 speakers to the AV Enter Setup Zone 2 Out SettingsZone2 InputControlling Zone 2 from the AV receiver Using ZoneControlling Zone 2 with the Remote Controller Adjusting the Tone of Zone Adjusting the Volume of ZoneAdjusting the Balance of Zone Muting ZoneMiscellaneous, and then press Enter Using the 12V TriggersWhen you’ve finished, press the Setup button Using a Multiroom Kit with Other Components Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Zone Entering Remote Control Codes Preprogrammed Remote Control CodesControlling Other Components 100Resetting the Remote Mode Buttons Resetting the Remote Controller101 Controlling Other ComponentsControlling a TV 102Controlling a DVD Player, or DVD Recorder 103104 Play Mode buttonControlling a VCR or DVR Previous buttonControlling a Satellite Receiver or Cable Receiver 105Controlling a CD Player, CD Recorder, or MD Player 106Search button Disc +/- buttonControlling an RI Dock 107Controlling a Cassette Recorder 108109 Troubleshooting110 Troubleshooting111 Important Note Regarding Video Playback 112113 SpecificationsOutput Video Resolution Chart114 115 Onscreen Setup MenusMenu Map Main menuOnkyo Corporation 116

DTR-5.9 specifications

The Integra DTR-5.9 is a versatile and powerful home theater receiver designed to meet the needs of audiophiles and casual listeners alike. This receiver stands out in a crowded market due to its robust feature set, superior sound quality, and advanced technologies that enhance the overall listening experience.

One of the main features of the Integra DTR-5.9 is its multi-channel amplification. With 7.1 channel amplification, it delivers a total power output of 100 watts per channel, allowing for immersive audio experiences whether you're watching movies, playing video games, or listening to music. This makes it an ideal choice for surround sound setups, enabling discrete sound placement in a home theater environment.

The DTR-5.9 also offers a rich array of connectivity options. It comes equipped with HDMI inputs and outputs, supporting 4K video pass-through, which ensures compatibility with the latest high-definition video formats. This feature is crucial for users who want to enjoy crisp and clear visuals from their Blu-ray players, gaming consoles, and streaming devices. The receiver also includes multiple composite and component video inputs, as well as analog inputs for older devices, ensuring that users can connect a variety of equipment.

In terms of audio processing, the Integra DTR-5.9 utilizes advanced technologies such as Dolby TrueHD and DTS-HD Master Audio, which provide high-resolution audio formats for a more immersive listening experience. The incorporation of Audyssey MultEQ XT room correction technology allows the receiver to analyze room acoustics and optimize speaker performance, delivering balanced sound tailored to the specific environment.

Additionally, the DTR-5.9 is equipped with built-in network functionality, enabling seamless streaming from popular services like Spotify, Pandora, and internet radio stations. Users can also access their own music libraries via USB ports, contributing to the versatility of playback options.

Its intuitive graphical user interface and remote control simplify navigation, making it easy for users to customize settings and switch between sources effortlessly. The build quality of the Integra DTR-5.9 is notable, reflecting a commitment to durability and performance, ensuring that it remains a reliable cornerstone in your entertainment system for years to come.

In summary, the Integra DTR-5.9 combines powerful amplification, versatile connectivity, advanced audio processing technologies, and user-friendly features, making it a compelling choice for anyone looking to elevate their home audio experience. Whether for movies, music, or gaming, this receiver is designed to deliver high-performance sound and video, meeting the demands of modern home entertainment systems.
Top Page Image Contents