Integra DTR-9.1 appendix Connecting a LD player, Connecting a video cassette recorder

Page 19

Example of how to connect your equipment

6. Connecting a LD player

Using an RCA-type video connection cable, connect the video output terminal (composite) on the LD player to the VIDEO 4 IN jack on the DTR-9.1. If there is an S- video output terminal on the LD player, connect it to the S VIDEO 4 IN jack using an S-video cable.

If the LD player has an AC-3RF output, connect it to the AC-3RF jack on the DTR-9.1. If this connection is made, “AC-3RF” must be set in the OSD Menu: Input Setup → Digital Setup → Digital Format (see page 34).

Using an RCA-type audio connection cable, connect the audio output terminal on the LD player to the audio VIDEO 4 IN jacks on the DTR-9.1. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the LD player has a digital output jack as well, be sure to also connect it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT (OPTICAL) jack on the DTR-9.1 de- pending on the type of connector on the LD player.

With the initial settings of the DTR-9.1, the VIDEO 4 input source is set for digital input at the COAXIAL 4 jack. If the digital connection is made at a different jack, this must be changed at the OSD Menu: Input Setup → Digital Setup → Digital Input (see page 34).

7. Connecting a video cassette recorder

Using an RCA-type video connection cable, connect the video output terminal (composite) on the video cassette recorder to the VIDEO 1 IN jacks on the DTR-9.1 and video input terminal to the VIDEO 1 OUT jacks. If there is an S-video input/output terminal on the video cassette recorder, connect it to the S VIDEO 1 IN/OUT jack using an S-video cable. If the video cassette re- corder has component video outputs, connect them to one of the COMPONENT VIDEO INPUT jacks.

Using an RCA-type audio connection cable, connect the audio output terminal on the video cassette re- corder to the same VIDEO 1 IN audio jacks on the DTR-

9.1and audio input terminal to the VIDEO 1 OUT audio jacks. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

8. Connecting a satellite tuner or television

Using an RCA-type video connection cable, connect the video output terminal (composite) on the satellite tuner or television to the VIDEO 3 IN jacks on the DTR-

9.1.If there is an S-video output terminal on the satellite tuner or television, connect it to the S VIDEO 3 IN jack using an S-video cable. If the satellite tuner or television has component video outputs, connect them to one of the COMPONENT VIDEO INPUT jacks.

Using an RCA-type audio connection cable, connect the audio output terminal on the satellite tuner or tele- vision to the same VIDEO 3 IN audio jacks on the DTR-

9.1.Make sure that you properly connect the left chan- nel to the L jack and the right channel to the R jack.

If the satellite tuner or television has a digital output jack as well, be sure to also connect it to either a DIGI- TAL INPUT (COAXIAL) or DIGITAL INPUT (OPTICAL) jack on the DTR-9.1 depending on the type of connector on the set top box or television.

With the initial settings of the DTR-9.1, the VIDEO 3 input source is set for digital input at the COAXIAL 3 jack. If the digital connection is made at a jack different from

the initial settings, this must be changed at the OSD Menu: Input Setup → Digital Setup → Digital Input (see page 34).

9.Connecting a DVD recorder or other digital video recording device

Using an RCA-type video connection cable, connect the video output terminal (composite) on the device to the VIDEO 2 IN jacks on the DTR-9.1 and video input ter- minal to the VIDEO 1 OUT jacks. If there is an S-video input/output terminal on the device, connect it to the S VIDEO 2 IN/OUT jack using an S-video cable. If the de- vice has component video outputs, connect them to one of the COMPONENT VIDEO INPUT jacks.

Using an RCA-type audio connection cable, connect the audio output terminal on the device to the same VIDEO 2 IN audio jacks on the DTR-9.1 and audio input terminal to the VIDEO 1 OUT audio jacks. Make sure that you properly connect the left channel to the L jack and the right channel to the R jack.

If the device has a digital output jack as well, be sure to also connect it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT (OPTICAL) jack on the DTR-9.1 depend- ing on the type of connector on the device.

With the initial settings of the DTR-9.1, the VIDEO 2 input source is set for digital input at the COAXIAL 2 jack. If the digital connection is made at a jack different from the initial settings, this must be changed at the OSD Menu: Input Setup → Digital Setup → Digital Input (see page 34).

If the device also has a digital input jack, it can be con- nected to the DIGITAL OUTPUT (COAXIAL) or DIGITAL OUTPUT (OPTICAL) jack on the DTR-9.1 for recording of the signal from the input source selected at the DTR-9.1.

10. Connecting a television monitor or projector

Using an RCA-type video connection cable, connect the video input terminal (composite) on the monitor to one of the MONITOR OUT jacks on the DTR-9.1. If there is an S-video input terminal on the monitor, connect it to the S VIDEO MONITOR OUT jack using an S-video cable. If the device has component video inputs, connect them to the COMPONENT VIDEO OUTPUT jacks.

Note that the OSD Menu will not be displayed on the monitor connected to MONITOR OUT 2. This allows you to connect large screens or projectors to MONITOR OUT 2 and use a smaller television connected to MONITOR OUT 1 just to make settings in the OSD Menu.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents DTR-9.1 Avis Important SafeguardsModele pour les Canadien PrecautionsFor U.S. model For Canadian modelContents Contents Supplied accessoriesAssignable and Configuaragble 12-Volt Trig FeaturesTHX Ultra Using the remote controller Before using remote controllerFront panel display Front panel facilitiesFront panel Front panel doorFront panel facilities Off TuningPreset FM ModeSEND/LEARN indicator LCD display Power ON/STNBY button Remote controllerModel NO. DTR-9.1 Rear panel facilitiesCoaxial, optical, and input-only AC-3RF Rear panel facilitiesAC Inlet Video IN/OUT Video Monitor OUT Example of how to connect your equipmentDefault setting Example of how to connect your equipmentStandard connections Connecting a compact disc player Connecting your audio componentsConnecting a turntable Connecting an MD recorder, DAT deck, or CD recorderConnecting a television monitor or projector Connecting a LD playerConnecting a video cassette recorder Connecting a satellite tuner or televisionSpeaker placement Connecting speakersIdeal speaker configuration Minimum speaker configuration for surround sound playbackConnecting a subwoofer Connecting speakersConnecting the AM loop antenna Connecting antennasAssembling the AM loop antenna Directional linkage Connecting antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaConnecting the main and remote zones Connecting to the IR in Zone 2 inputOutline Cabinet Connecting to the IR in Main inputRemove the jumper plugs Connect the power amplifiers Connecting a graphic equalizer Connecting power amplifiersRemove the jumper plugs Connect a graphic equalizer Turning the power on from the remote controller Connecting the powerOSD menu consists of a main screen that is divided Up into six menus Speaker Setup, Input Setup, ListeningOn-Screen Display OSD menu Your home theater, and it rarely needs to be Changed laterNavigating through the OSD menu On-Screen Display OSD menuPress the Menu button Speaker Config sub-menu Speaker SetupSpeaker Distance sub-menu Speaker SetupCalibrating the speaker levels Level Calibration sub-menuBass Peak Level Bass Peak Level Manager* sub-menu LFE Level Setup sub-menuDigital Setup sub-menu Input SetupInput Setup Video Setup sub-menu Multichannel Setup sub-menuDTS Mpeg Listening Mode Preset sub-menuListening Modes Input source signalsInput Setup 123456789012345678901234 4.Preference Delay sub-menu Sound Effect sub-menuCharacter Input sub-menu Miscellaneous SetupListening Mode Setup menu Listening Mode SetupListening Mode Setup Description listening mode parameters THX Preference Volume Setup sub-menuPreference OSD Setup sub-menuOSD Tweak Version Zone2 OSD SetupLock Setup sub-menu AboutInput selector buttons Power VOLEnjoying music or videos in the remote zone Press the Zone 2 button on the DTR-9.1 Select a sourceListening to Radio Broadcasts PresetListening to FM/AM Radio Stations Press the Memory button on the front panel Press the Enter button again to finalize the procedureThis erases the selected preset station Listening to Radio BroadcastsUsing the many features of the DTR-9.1 Changing the listening modeSelecting an input source Listening with headphones Adjusting the volumeIf one of the messages shown below appears Enjoying music or videos with the DTR-9.1Enjoying the multichannel output Press the Rec Out button twice within 8 seconds Recording a sourceStart recording at the recording component as desired Recording a source Controlling the DTR-9.1 Using remote controllerUsing the remote controller to control each device Press the AUDIO/TAPE Mode buttonListening mode buttons Using remote controllerControlling an Integra MD recorder Press the CD Mode buttonPress the MD Mode button Controlling an Integra CD playerPress the TUN input selector button Controlling an Integra cassette tape deckSAT, CABLE, VCR, and TV Mode buttons Press the DVD Mode buttonControlling an Integra DVD player Buttons Programming procedurePage You can only erase memorized commands and not preset ones Erasing the programmed command from one buttonPress and release the same Mode button again SEND/LEARN indicator Mode buttonsRunning a Macro function Using a Macro functionPress the Mode Macro button to complete the programming Programming a Macro functionCheck to see if the macro has been properly programmed Using a Macro functionPress the Direct Macro button to complete the procedure Programming the Direct Macro functionPress the Direct Macro button again Press the Mode Macro button againOperation Erasing all commands and macros that have been programmedMacro mode programming memo Press the ENT buttonTroubleshooting guide Troubleshooting guide LFE Level function cannot be used OSD menu settings cannot be changedCannot change OSD Menu settings Late Night function cannot be usedZone2 OSD Setup Default settingsSpeaker Setup Input SetupInputs Your system settingTape Your system settingSpeakers OSD SetupMode Remote controllerSpecifications Other upgraded function Upgraded-2 Important points regarding speaker placement Speaker configuration and placement/ Connecting speakersCrossover80HzTHX QuitOSD Boundary Gain Channel digital surround format Digital Setup sub-menu Listening Mode Preset sub-menuRelationship between input source and listening mode Upgraded-8 THX When Upsampling is set to On, DTS Neo6 cannot be selected DTS-ES Upgraded-12 DTS-ES Upgraded-14 Parameter Delay sub-menu Other upgraded function

DTR-9.1 specifications

The Integra DTR-9.1 is a high-performance 7.1-channel surround sound receiver designed for audiophiles and home theater enthusiasts who demand superior sound quality and advanced features. This model, crafted by the renowned manufacturer Integra, showcases a blend of cutting-edge technology and user-friendly operation, making it a standout choice for home entertainment systems.

One of the notable features of the DTR-9.1 is its robust amplification system. Equipped with discrete high-current amplifiers, it delivers a powerful output of 130 watts per channel, ensuring dynamic sound reproduction for movies, music, and gaming. The receiver supports various surround sound formats, including Dolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio, and DTS Neo:6, providing an immersive audio experience that brings your media to life.

The DTR-9.1 incorporates advanced video processing capabilities, including upscaling of standard definition and high definition content to 1080p via HDMI, ensuring that your visuals maintain clarity and detail. With multiple HDMI inputs and outputs, this receiver offers extensive connectivity options, accommodating various devices such as Blu-ray players, gaming consoles, and streaming devices.

Another significant aspect of the Integra DTR-9.1 is its integration of Audyssey technologies, specifically Audyssey MultEQ and Audyssey DynamicEQ. These features enable automatic room calibration, optimizing speaker settings to adapt to the acoustic characteristics of your space. This ensures balanced sound reproduction across all frequencies, providing an enhanced listening environment.

In addition, the DTR-9.1 is equipped with a user-friendly interface and an ergonomic remote control, offering ease of navigation through its features. The on-screen display is intuitive, making it accessible for users to adjust settings and preferences with minimal hassle.

For music enthusiasts, the receiver supports streaming services and includes built-in Bluetooth and Wi-Fi connectivity, allowing for seamless streaming from smartphones or tablets. The DTR-9.1 also features a Zone 2 output, enabling multi-room audio setups, delivering flexibility in how and where to enjoy your favorite tunes.

Overall, the Integra DTR-9.1 combines exceptional sound quality, versatile connectivity, and advanced technologies, making it a top choice for consumers looking to enhance their home audio and video experience. Whether used for thrilling movie nights or casual music listening, this receiver promises to deliver performance and satisfaction for discerning users.
Top Page Image Contents