Integra DTR-9.1 appendix Connecting antennas, Connecting the AM loop antenna

Page 22

Connecting antennas

Connecting the included antennas

Connecting the FM indoor antenna:

The FM indoor antenna is for indoor use only. During use, extend the antenna and move it in various direc- tions until the clearest signal is received. Fix it with push pins or similar implements in the position that will cause the least amount of distortion.

If the reception is not very clear with the attached FM indoor antenna, the use of an outdoor antenna is rec- ommended.

Connecting the AM loop antenna:

The AM loop antenna is for indoor use only. Set it in the direction and position where you receive the clearest sound. Put it as far away as possible from the DTR-9.1, televisions, speaker cables, and power cords.

When reception is not satisfactory with the attached AM loop antenna alone, connection of an outdoor antenna is recommended.

(indoor) AM loop antenna

Assembling the AM loop antenna

Assemble the loop antenna as shown in the illustration.

•Refer to the next page for details on connecting the AM loop antenna.

Insert into the hole.

FM antenna

Strip away the insulation from the end of the cable, then fully insert the stripped end of the cable.

ANTENNA

AM

FM 75

Connecting the AM antenna cable

1.Press down the lever.

2.Insert the wire into the hole.

3.Release the lever.

1

2

3

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents DTR-9.1 Important Safeguards AvisFor Canadian model PrecautionsFor U.S. model Modele pour les CanadienContents Supplied accessories ContentsAssignable and Configuaragble 12-Volt Trig FeaturesTHX Ultra Before using remote controller Using the remote controllerFront panel door Front panel facilitiesFront panel Front panel displayFront panel facilities FM Mode TuningPreset OffRemote controller SEND/LEARN indicator LCD display Power ON/STNBY buttonRear panel facilities Model NO. DTR-9.1Rear panel facilities Coaxial, optical, and input-only AC-3RFAC Inlet Video IN/OUT Example of how to connect your equipment Video Monitor OUTDefault setting Example of how to connect your equipmentStandard connections Connecting an MD recorder, DAT deck, or CD recorder Connecting your audio componentsConnecting a turntable Connecting a compact disc playerConnecting a satellite tuner or television Connecting a LD playerConnecting a video cassette recorder Connecting a television monitor or projectorMinimum speaker configuration for surround sound playback Connecting speakersIdeal speaker configuration Speaker placementConnecting speakers Connecting a subwooferConnecting the AM loop antenna Connecting antennasAssembling the AM loop antenna Connecting an AM outdoor antenna Connecting antennasConnecting an FM outdoor antenna Directional linkageConnecting the main and remote zones Connecting to the IR in Zone 2 inputOutline Connecting to the IR in Main input CabinetRemove the jumper plugs Connect the power amplifiers Connecting a graphic equalizer Connecting power amplifiersRemove the jumper plugs Connect a graphic equalizer Connecting the power Turning the power on from the remote controllerYour home theater, and it rarely needs to be Changed later Up into six menus Speaker Setup, Input Setup, ListeningOn-Screen Display OSD menu OSD menu consists of a main screen that is dividedNavigating through the OSD menu On-Screen Display OSD menuPress the Menu button Speaker Setup Speaker Config sub-menuSpeaker Setup Speaker Distance sub-menuLevel Calibration sub-menu Calibrating the speaker levelsLFE Level Setup sub-menu Bass Peak Level Bass Peak Level Manager* sub-menuInput Setup Digital Setup sub-menuInput Setup Multichannel Setup sub-menu Video Setup sub-menuListening Mode Preset sub-menu DTS MpegInput source signals Listening ModesInput Setup Delay sub-menu Sound Effect sub-menu 123456789012345678901234 4.PreferenceMiscellaneous Setup Character Input sub-menuListening Mode Setup Listening Mode Setup menuListening Mode Setup Description listening mode parameters THX Volume Setup sub-menu PreferencePreference OSD Setup sub-menuOSD Tweak About Zone2 OSD SetupLock Setup sub-menu VersionPress the Zone 2 button on the DTR-9.1 Select a source Power VOLEnjoying music or videos in the remote zone Input selector buttonsListening to Radio Broadcasts PresetListening to FM/AM Radio Stations Listening to Radio Broadcasts Press the Enter button again to finalize the procedureThis erases the selected preset station Press the Memory button on the front panelAdjusting the volume Changing the listening modeSelecting an input source Listening with headphones Using the many features of the DTR-9.1If one of the messages shown below appears Enjoying music or videos with the DTR-9.1Enjoying the multichannel output Press the Rec Out button twice within 8 seconds Recording a sourceStart recording at the recording component as desired Recording a source Press the AUDIO/TAPE Mode button Using remote controllerUsing the remote controller to control each device Controlling the DTR-9.1Using remote controller Listening mode buttonsControlling an Integra CD player Press the CD Mode buttonPress the MD Mode button Controlling an Integra MD recorderControlling an Integra cassette tape deck Press the TUN input selector buttonSAT, CABLE, VCR, and TV Mode buttons Press the DVD Mode buttonControlling an Integra DVD player Programming procedure ButtonsPage SEND/LEARN indicator Mode buttons Erasing the programmed command from one buttonPress and release the same Mode button again You can only erase memorized commands and not preset onesProgramming a Macro function Using a Macro functionPress the Mode Macro button to complete the programming Running a Macro functionProgramming the Direct Macro function Using a Macro functionPress the Direct Macro button to complete the procedure Check to see if the macro has been properly programmedPress the Mode Macro button again Press the Direct Macro button againPress the ENT button Erasing all commands and macros that have been programmedMacro mode programming memo OperationTroubleshooting guide Troubleshooting guide Late Night function cannot be used OSD menu settings cannot be changedCannot change OSD Menu settings LFE Level function cannot be usedInput Setup Default settingsSpeaker Setup Zone2 OSD SetupYour system setting InputsYour system setting TapeOSD Setup SpeakersRemote controller ModeSpecifications Other upgraded function Upgraded-2 Speaker configuration and placement/ Connecting speakers Important points regarding speaker placementCrossover80HzTHX QuitOSD Boundary Gain Digital Setup sub-menu Listening Mode Preset sub-menu Channel digital surround formatRelationship between input source and listening mode Upgraded-8 THX When Upsampling is set to On, DTS Neo6 cannot be selected DTS-ES Upgraded-12 DTS-ES Upgraded-14 Parameter Other upgraded function Delay sub-menu

DTR-9.1 specifications

The Integra DTR-9.1 is a high-performance 7.1-channel surround sound receiver designed for audiophiles and home theater enthusiasts who demand superior sound quality and advanced features. This model, crafted by the renowned manufacturer Integra, showcases a blend of cutting-edge technology and user-friendly operation, making it a standout choice for home entertainment systems.

One of the notable features of the DTR-9.1 is its robust amplification system. Equipped with discrete high-current amplifiers, it delivers a powerful output of 130 watts per channel, ensuring dynamic sound reproduction for movies, music, and gaming. The receiver supports various surround sound formats, including Dolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio, and DTS Neo:6, providing an immersive audio experience that brings your media to life.

The DTR-9.1 incorporates advanced video processing capabilities, including upscaling of standard definition and high definition content to 1080p via HDMI, ensuring that your visuals maintain clarity and detail. With multiple HDMI inputs and outputs, this receiver offers extensive connectivity options, accommodating various devices such as Blu-ray players, gaming consoles, and streaming devices.

Another significant aspect of the Integra DTR-9.1 is its integration of Audyssey technologies, specifically Audyssey MultEQ and Audyssey DynamicEQ. These features enable automatic room calibration, optimizing speaker settings to adapt to the acoustic characteristics of your space. This ensures balanced sound reproduction across all frequencies, providing an enhanced listening environment.

In addition, the DTR-9.1 is equipped with a user-friendly interface and an ergonomic remote control, offering ease of navigation through its features. The on-screen display is intuitive, making it accessible for users to adjust settings and preferences with minimal hassle.

For music enthusiasts, the receiver supports streaming services and includes built-in Bluetooth and Wi-Fi connectivity, allowing for seamless streaming from smartphones or tablets. The DTR-9.1 also features a Zone 2 output, enabling multi-room audio setups, delivering flexibility in how and where to enjoy your favorite tunes.

Overall, the Integra DTR-9.1 combines exceptional sound quality, versatile connectivity, and advanced technologies, making it a top choice for consumers looking to enhance their home audio and video experience. Whether used for thrilling movie nights or casual music listening, this receiver promises to deliver performance and satisfaction for discerning users.
Top Page Image Contents